-
-23%
A2212 1000KV Brushless DC Motor
Original price was: ₨1,500.00.₨1,150.00Current price is: ₨1,150.00. Quick View- Model: A2212 10T
- Motor KV (RPM/V): 1400
- Maximum Efficiency: 80%
- Current Capacity: 16A Per 60S
- No-Load Current(A): 0.7A @10V
- Max. Efficiency Current: 6-12A
- Maximum Watts(W): 180
- Internal Resistance(mΩ): 65
- Poles: 14
- Shaft Diameter (mm): 3.17
- LiPO Batteries: 2S-3S
- Length (mm): 27.5
- Width (mm): 26.5
- Weight (gm): 62
-
-20%
A2212 2200KV Brushless DC Motor BLDC
Original price was: ₨1,500.00.₨1,199.00Current price is: ₨1,199.00. Quick View- Recommended Voltage: 2-12VDC
- Internal Resistance: 90mΩ
- Shaft Size: 3.17mm (1.8″)
- Shaft Length: 11mm
- Motor Diameter: 27.5mm
- Motor Length (Overall): 40mm
- Current Capacity: 12A/60s
- Max Efficiency: 80%
- Max Power: 239W
- Recommended ESC: Minimum Of 18A
- Recommended Model Weight: 300-1000g
- Mounting Holes: M3
- Wire Length: ~70mm
-
-10%
A3967 Stepper Motor Driver Module
Original price was: ₨400.00.₨360.00Current price is: ₨360.00. Quick ViewThis EasyDriver compatible stepper motor driver module utilizes the Allegro A3967SLB micro-stepping driver to proved a simple and compact means of driving bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors from a microcontroller. By default, the module will accept a 5V TTL step and direction signal from the microcontroller to stop the motor in either full, half, quarter, and eighth-step modes. By shorting jumper SJ2 it can also be configured to be compatible with 3.3V microcontrollers that are not 5V tolerant. An onboard potentiometer allows for setting maximum drive current.
-
-23%
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection/choice.
- Mixed with slow current decay mode.
- The low power dissipation of synchronous rectifier.
- Internal UVLO(ultra voltage lockout).
- Crossover current protection.
- Thermal shutdown circuit.
- Ground fault protection.
- Loading and short circuit protection.
- The optional five-step mode: full, 1/2, 1/4, 1/8 and 1/16.
-
AA 2Cell holder especially design for student science project kit and many more application in 3 volt supply.
-
AA 4 Cell Battery Holder Need 6V 1.5V cell or 4.8V with 1.2V cell to run a project on AA batteries This is a simple battery holder that we use in some of our kits. What we like about these are the leads that come pre-attached, ready to be soldered to a PCB, or attached with your choice of connector.
- Two mounting holes to accept flush head screws.
- You can also use high adhesive double-sided tape, or a glue gun to attach to your project or prototype.
- This battery holder has two wires 6 inches of 24-gauge leads that have 5 mm of insulation stripped off of the ends.
-
-45%
ABS Enclosure Black Case for Raspberry Pi with Heat Sink And 5v Fan
Original price was: ₨2,000.00.₨1,099.00Current price is: ₨1,099.00. Quick ViewThis Raspberry case is made of ABS material. It can be perfectly compatible with Raspberry Pi 4B. Considering the high power consumption cost of Raspberry Pi 4B, the Raspberry case has room to add a fan (35x35x10mm) and general copper/aluminum heatsink (up to 6mm) for heat dissipation. What’s more The case supports the GPIO PINs of the Raspberry Pi 4B and connects external devices like Raspberry Pi Hat outside the case by cables. Also, the ventilation openings are designed on the top and bottom of the case to keep cooling.
-
-12%
AC 220V 100W Aluminum PTC Heater Thermostat Plate
Original price was: ₨1,700.00.₨1,499.00Current price is: ₨1,499.00. Quick ViewItems details AC 220V 100W Aluminum PTC Heater Thermostat Heating Plate constant temperature basic parameter: PTC heater size: 67*70*6mm AC 220 volts 100 watts,250-260 degree Celsius automatic constant temperature.
-
-29%
AC 220V Temperature Controller RKC REX-C700
Original price was: ₨3,500.00.₨2,499.00Current price is: ₨2,499.00. Quick View- Type: Digital
- Theory: Temperature Controller
- Usage: Industrial
- Model Number: REX-C700 Power
- Type: Charger Display
- Size:1.9 Inches & Under Max
- Measuring Temperature:120°C & Above
- Style: Standing Station
- Size:72*72mm
- Input: Universal Control
- output: Relay Alarm
- Display: Celsius °C Unit
- Type: piece
- Package Weight: 0.4kg (0.88lb.)
-
-40%
AC/DC 60W Ceiling Fan Circuit Kit | Solar & BLDC Fan Controller
Original price was: ₨2,500.00.₨1,499.00Current price is: ₨1,499.00. Quick View -
-32%
Acrylic Rectangle 0.56 Inch 3 Digit 7 Segment Display
Original price was: ₨130.00.₨89.00Current price is: ₨89.00. Quick View- Operating current: 10mA
- Bright Red LED chip, which is made from AlGaAs on GaAs substrate
- Low Current Consumption
- High Brightness
- Blackface and RED LED segments
-
-6%
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -20A~ 20A
- Sensitivity: 100mV/A
- The current sensor chips: ACS712_ELC-20A.
- Pin 5V power supply, onboard power indicator.
- There is no the detection current through, the output voltage is VCC / 2.
- The module can be measure plus or minus 20 amps, corresponding to the analog output of 185 mV / A.
-
-10%
Out Of StockACS712 Current Sensor 30A current sensor board is based on the Allegro ACS712ELCTR-30A bi-directional hall-effect current sensor chip that detects positive and negative flowing currents in the range of minus 30 Amps to positive 30 Amps. The board operates at 5V DC and the current flow through the sensor is converted to an output voltage starting at 1/2Vcc (or 2.5V) for no current flow and moves up 66mV per amp for positive current or down -66mV per amp for negative current.
-
-7%
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -5A~ 5A
- Sensitivity: 66mV/A
- The current sensor chips: ACS712_ELC-05B.
- Pin 5V power supply, onboard power indicator.
- There is no the detection current through, the output voltage is VCC / 2.
-
-36%
Activity High Quality 50g or 100g Soldering Wire for Soldering Works
Price range: ₨359.00 through ₨729.00 Quick View- Diameter: 0.031″ (0.8mm)
- Weight: 0.11lbs (50g) or (100g)
- Composition: 70% Tin, 30% Lead
- Rosin Flux Content: 2%
-
-40%
Out Of StockAD112-50FM Digital Multifunction Power Meter – LCD Display | AC Voltage, Current, Power, Frequency & Energy Monitor
Original price was: ₨4,992.00.₨2,999.00Current price is: ₨2,999.00. Quick View- Voltage Range: AC 80.0-300.0V
- Current Range: AC 0-99.99A (0.01A resolution)
- Power Factor: 0.00-1.00PF
- Active Power Range: 0-45,000W
- Energy Measurement: 0-99,999kWh
- Operating Temperature: -25°C to 85°C
- Dimensions: 79 x 43 x 48mm
-
-19%
Out Of StockThe AD7528 is a monolithic dual 8-bit digital/analog converter featuring excellent DAC-to-DAC matching. It is available in skinny 0.3″ wide 20-lead DIPs and in 20-lead surface mount packages. Separate on-chip latches are provided for each DAC to allow easy microprocessor interface.
-
-10%
Out Of StockAdjustable Soldering Iron 80W 220V/110V LCD Digital Display
Original price was: ₨2,000.00.₨1,799.00Current price is: ₨1,799.00. Quick View -
-32%
ADS1115 Analog-to-Digital Converter
Original price was: ₨1,100.00.₨749.00Current price is: ₨749.00. Quick View- WIDE SUPPLY RANGE: 2.0V to 5.5V
- LOW CURRENT CONSUMPTION: Continuous Mode: Only 150µA Single-Shot Mode: Auto Shut-Down
- PROGRAMMABLE DATA RATE: 8SPS to 860SPS
- INTERNAL LOW-DRIFT VOLTAGE REFERENCE
- INTERNAL OSCILLATOR
- INTERNAL PGA
- I2C INTERFACE: Pin-Selectable Addresses
- FOUR SINGLE-ENDED OR TWO DIFFERENTIAL INPUTS
- PROGRAMMABLE COMPARATOR
- This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers
-
-20%
Hall effect sensor is transducing devices used to detect and generate a voltage when in the presence of a magnetic field. They are designed to induce a voltage as an output when a magnetic field is present at its input. The output voltage can be variable depending on the magnitude of the magnetic field. Hall effect sensors, as they name states are effect sensors, which can be used to sense different categories, like speed, position of objects, rotational speed or frequency and be used as a fault detector. They can be used to detect a time-varying current, as time-varying current produce magnetic fields, which can then be sensed by the Hall effect transducer and produce a voltage with some proportion the amount of magnetic field present at the sensor.
-
-33%
AMTECH RMA223 RMA-223 RMA559 Solder Paste Flux 10CC
Original price was: ₨299.00.₨199.00Current price is: ₨199.00. Quick View- Flux Type: Original AMTECH RMA-223 UV (Made in USA)
- Volume: 10ml/10cc
- Dimension: 93 x 33 x 23mm
- Material: the mixture of high-quality alloyed powder and resinic pasty flux, it can avoid the pale yellow residue.
- Color: Colorless/Transparent
- Insulated: Yes
- With Needle Tip: Yes
- Made in: USA
- Application: for soldering and reballing of computer and phone chips.
- Advantage: Good immersion and high-intensity joint.
- Function: for PCB, BGA, and PGA reworking.
- 100%: New Type, high quality.
-
-20%
Out Of StockThis analog multimeter has a capability of measuring DC voltages having four range setting, DC current having three range setting, AC voltages having four range setting and resistance having three range setting.
-
-14%
Out Of StockAnalog Servo HD 1501mg
Original price was: ₨5,800.00.₨4,999.00Current price is: ₨4,999.00. Quick ViewIt is a metal geared analog servo which can deliver extra high torque as compared many high power servo motors
-
-26%
Out Of StockAnalog Timer H3BA-8 24VDC Timer Relay
Original price was: ₨2,550.00.₨1,899.00Current price is: ₨1,899.00. Quick View -
-23%
Analog Timer Relay H3BA-8 12V
Original price was: ₨1,550.00.₨1,199.00Current price is: ₨1,199.00. Quick View- Model: H3BA-8
- Brand: Omron
- Output: DPDT
- Usage/Application: INDUSTRIAL
- Rated Current: 5A 12VAC
- Mounting Type: Panel Mounting Timer
- Display Type: Analog
- Automation Grade: Semi-Automatic
-
-23%
Analog Timer Relay H3BA-8 220V
Original price was: ₨1,500.00.₨1,149.00Current price is: ₨1,149.00. Quick View- Model: H3BA-8
- Brand: Omron
- Output: DPDT
- Usage/Application: INDUSTRIAL
- Rated Current: 5A 220VAC
- Mounting Type: Panel Mounting Timer
- Display Type: Analog
- Automation Grade: Semi-Automatic
-
-40%
- LDR module 4 PIN
- Operating voltage 3.3V-5V
- Signal output indicator light.
- LDR module 4 PIN
- Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)
-
-11%
- Charge your smartphone with this Micro USB cable
- Enjoy smooth data transfers to/from computer, laptops
- 1.5 Meter length cable
- Lasts upto 10X longer than conventional cable.
- Safe & Smart
- Durable Product
-
Android charging cable for smart phones.
-
-27%
ANENG ST212 Digital DC/AC Clamp Meter Current 400A Amp Multimeter Large Color Screen
Original price was: ₨11,000.00.₨7,999.00Current price is: ₨7,999.00. Quick View- AC Current Range: 60A/400A
- DC Current Range: 60A/400A
- DC Voltage Range: 600V/600mV
- AC Voltage Range: 600V/600mV
- Resistance: 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ
- Capacitance: 60nF/600nF/6uF/60uF/600uF/6mF/60mF
- Temperature: -40~1000℃, -40~1832℉
- Frequency: 60Hz/1000Hz
- Colour: Red
- Material: ABS
- Display: LCD
- Max. Display Value: 6000 digit
- Sampling Time: About 3 times/second, bargraph 10 times/second
- Auto-off: 15 minutes
- Operating Temperature: 18~28℃
- Storage Temperature: -10~50℃
- Operating Height: Max. 2000m
- Power Supply: 2 * 1.5V AAA battery (NOT included)
- Item Size: 182 * 62.1 * 33.4mm / 7.17 * 2.44 * 1.31in
- Item Weight: 150g / 5.29oz
- Package Weight: 272g / 9.59oz
- Package Size: 21.7 * 8.5 * 4.5cm / 8.54 * 3.35 * 1.77in
-
-25%
APDS9960 proximity and light intensity sensor I2C 3.3V
Original price was: ₨799.00.₨599.00Current price is: ₨599.00. Quick View- Gesture recognition using reflected IR
- Digital proximity sensing using reflected IR
- Separate Red/Green/Blue light intensity sensors
- Ambient (clear) light intensity sensor
- IR light-blocking filter
- Interrupt output available
- I2C interface with good library support
- 3.3V operation
-
-15%
Out Of StockThe power module has the ability to provide APM lossless power from a LiPo battery as well as current consumption and voltage measurements through 6-pos cable. The on board regulator switch has the ability of giving outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery.
-
Out Of StockThe ArduPilot Mega 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. This version is ready to use, with no assembly required. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints.
This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it’s often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass, so that the GPS/Compass unit can be mounted further from noise sources than APM itself.
-
-21%
Out Of StockAPM2.8 ArduPilot Mega 2.8 Flight Control Board
Original price was: ₨19,000.00.₨15,000.00Current price is: ₨15,000.00. Quick ViewThis is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.
It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.
-
-24%
Arduino 28BYJ48 Stepper Motor
Original price was: ₨458.00.₨349.00Current price is: ₨349.00. Quick ViewArduino 28BYJ48 Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug. Motor: Diameter: 28mmVoltage: 5VStep angle: 5.625 x 1/64Reduction ratio: 1/64ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31x35mmPackage included:1 x ULN2003 driver board1 x 28BYJ-48 stepper motor Options:
-
-7%
Out Of Stock -
Out Of Stock- It is well designed to be durable during handling and repeated connections.
- Cable transfer speed is up to 480Mbps.
- USB Type: 2.0
- Data transfer rate: up to 480Mbps
- Connectors: USB type A tata-USB type B tata
- Length: 1.3 m
- Color: BLUE
-
-20%
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
-
-28%
Arduino Due AT91SAM3X8E ARM Cortex-M3 Board
Original price was: ₨6,240.00.₨4,500.00Current price is: ₨4,500.00. Quick View- MicrocontrollerAT91SAM3X8E
- Operating Voltage3.3V
- Input Voltage (recommended)7-12V
- Input Voltage (limits)6-16V
- Digital I/O Pins54 (of which 12 provide PWM output)
- Analog Input Pins12
- Analog Output Pins2 (DAC)
- Total DC Output Current on all I/O lines130 mA
- DC Current for 3.3V Pin800 mA
- DC Current for 5V Pin800 mA
- Flash Memory512 KB is all available for the user applications
- SRAM96 KB (two banks: 64KB and 32KB)Clock Speed84 MHz
- Length101.52 mm
- Width53.3 mm
- Weight36 g
-
-42%
Arduino Jumper Wire F/F 40Pcs
Original price was: ₨300.00.₨175.00Current price is: ₨175.00. Quick View- 40 pieces of the 10cm female to female color Dupont jumper wires cables in one set will be sold together.
- Color: as shown in the pictures.
- Material: durable hard plastic and copper wire.
- Each cable length: about 10cm /3.94 .
- Connectors: 1pin-1pin female to female header.
- 100% brand new and high quality 2.54mm Female to Female Color Dupont Jumper Wires Cables for Arduino Breadboard.
- Compatible with 2.54mm spacing pin headers.
- A popular choice for the construction or repair.
- Can be used for electronic project and Genuine Arduino products.
- Easy to install and use, durable and reusable to use.
-
Arduino jumper wire, male to male connector.
-
-40%
Arduino Jumper Wire M/F 40Pcs
Original price was: ₨300.00.₨179.00Current price is: ₨179.00. Quick View- Color: Multicolor.
- Material: durable hard plastic andcopper wire.
- Each cable length: about 10cm /3.94/.
- Connectors: 1pin-1pin male to female header.
- 100% brand new and high quality 2.54mm Male to Female Color Dupont Jumper Wires Cables for Arduino Breadboard.
- Compatible with 2.54mm spacing pin headers.
- A popular choice for the construction or repair.
- Can be used for electronic project and Genuine Arduino products.
- Easy to install and use, durable and reusable to use.
-
Arduino jumper wire, male to male connector.
-
-38%
Arduino Jumper Wire M/M 40Pcs
Original price was: ₨300.00.₨185.00Current price is: ₨185.00. Quick View- Compatible with 2.54 mm spacing pin headers.
- 120 pcs chromatic color jump wire.
- High quality and in good working condition.
- Durable and reusable.
- Easy to install and use.
- A popular choice for construction or repair.
- Be used for the electronic project and Genuine Arduino product.
- Flexible Breadboard Jumper Cable Wire allows you to plug and unplug easily for prototyping.
-
-9%
he Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
Hot-33%
Arduino MEGA 2560 PRO Mini
Original price was: ₨4,500.00.₨2,999.00Current price is: ₨2,999.00. Quick View- Microcontroller ATmega2560
- USB-TTL converter: CH340
- Power Out:5V-800mA
- Power IN.: 5V
- Power IN. VIN/DC Jack:5V
- Power Consumption: 5V 220mA
- Logic Level: 5V
- USB: Micro USB
- Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O: 54
- Analog I/O: 16
- Memory Size: 256kb
- Data RAM Type/Size: 8Kb
- Data ROM Type/Size: 4Kb
- Interface Type : ISP
- Operating temperature 40C/+85C
- Length x Width:38mmx54mm
-
Hot-8%
Arduino MEGA 2560 R3 ATMEGA16U2 Programing Board
Original price was: ₨4,000.00.₨3,699.00Current price is: ₨3,699.00. Quick View- Arduino Mega 2560 rev3 ATmega2560 microcontroller
- Input voltage – 7-12V
- 54 Digital I/O Pins (14 PWM outputs)
- 16 Analog Inputs
- 256k Flash Memory
- 16Mhz Clock Speed
-
Hot-42%
Arduino MEGA 2560 R3 ATMEGA16U2 Programing Board With Logo
Original price was: ₨6,000.00.₨3,499.00Current price is: ₨3,499.00. Quick View- Arduino Mega 2560 rev3 ATmega2560 microcontroller
- Input voltage – 7-12V
- 54 Digital I/O Pins (14 PWM outputs)
- 16 Analog Inputs
- 256k Flash Memory
- 16Mhz Clock Speed
-
Hot-55%
- Microcontroller: Atmel ATmega168 or ATmega328.
- Operating Voltage (logic level): 5 V.
- Input Voltage (recommended): 7-12 V.
- Input Voltage (limits): 6-20 V.
- Digital I/O Pins: 14 (of which 6 provide PWM output).
- Analog Input Pins: 8.
- DC Current per I/O Pin: 40 mA.
- Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB is used by the boot loader.
- SRAM : 1 KB (ATmega168) or 2 KB (ATmega328).
- EEPROM : 512 bytes (ATmega168) or 1 KB (ATmega328).
- Clock Speed: 16 MHz.
- Dimensions : 0.73 x 1.70
- Length: 45 mm.
-
-15%
The ProtoShield makes it easy for you to design custom circuits. You can easily solder TH or SMD ICs on the prototyping area to test them with your Arduino board. The SMD area is designed for a maximum of 24 pins SOIC integrated circuit and the TH area contains a lot of space for the needed components around your project. You can even stick a mini breadboard (not included) on the protoarea for solderless operation. The proto area includes also two power lines (IOREF and GND), two LEDs pads and SPI signals breakout pads for boards with SPI only on the ICSP header like Zero.
-
-30%
Out Of StockArduino Pro Micro 5v 16m Atmega32u
Original price was: ₨2,000.00.₨1,399.00Current price is: ₨1,399.00. Quick View- ATMEGA32U4 chip
- Supply Voltage: 5VDC
- Frequency: 16Mhz
- Four 10 bit ADC pins
- 12 pins Digital I/O
- Dimension: 33mm x 18mm
-
Hot-21%
Arduino Pro Mini 5V 16Mhz ATMEGA328
Original price was: ₨1,399.00.₨1,099.00Current price is: ₨1,099.00. Quick View- 131 Powerful Instructions – Most Single Clock Cycle Execution
- Up to 20 MIPS Throughput at 20 MHz
- Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
- One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
- Real Time Counter with Separate Oscillator
- Six PWM Channels
- 8-channel 10-bit ADC in TQFP and QFN/MLF package
- Programmable Watchdog Timer with Separate On-chip Oscillator
- On-chip Analog Comparator
- 23 Programmable I/O Lines
-
-49%
- It has a nice standard 0.1×0.1 prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- A IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- A surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out!
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
- It has a nice standard 0.1×0.1 prototyping grid with big pads
-
-10%
Arduino SD Card Reader Module
Original price was: ₨220.00.₨199.00Current price is: ₨199.00. Quick View- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V\
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
-
-15%
- It has a Pin 13 LED pilot.
- It has D0-D13 IO ports.
- A0-A5 analog IO ports.
- It contains a reset button.
- It also contains a Power LED.
- It has an SD card interface.
- It contains an Ultrasonic interface.
- This expansion board has an RS232 interface.
- It has a Bluetooth interface.
- It has an APC220 interface.
- IIC interface.
- 12864 LCD Parallel interfaces.
- It contains 12864 LCD Serial Interface
-
Hot-18%
Arduino Starter Kit RFID Based
Original price was: ₨8,500.00.₨6,999.00Current price is: ₨6,999.00. Quick ViewArduino Starter Kit RFID Based walks you through the basics of using the Arduino & RFID in a hands-on way. You’ll learn through building several creative projects. The kit includes a selection of the most common and useful electronic components with a book of 15 projects. Starting from the basics of electronics to more complex projects, the kit will help you control the physical world with sensors and actuators.
This kit aims to bring Arduino together with RFID technology, which will support individual production. With this kit, you will be able to use RFID with the code you wrote in Arduino. You will be able to come up with a practical technology such as Arduino, a technology that many people like RFID are trying to get into and stay away from using. All of the components and components required for RFID technology are combined in this kit.
Radio Frequency Identification (RFID) is the given name to the technology used to identify objects using radio waves. An RFID microchip embedded in a tag, keychain or card communicates with the reader/writer module to transfer data.
-
-60%
- ATmega328 microcontroller
- Input voltage – 7-12V
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- 32k Flash Memory
- 16Mhz Clock Speed
- ATmega328
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 6
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 150 mA
- Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM
- 2 KB (ATmega328) EEPROM
- 1 KB (ATmega328)
- Clock Speed 16 MHz
-
Hot-47%
Arduino UNO R3 Dip WITH CABLE
Original price was: ₨3,000.00.₨1,579.00Current price is: ₨1,579.00. Quick View- ATmega328 microcontroller
- Input voltage – 7-12V
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- 32k Flash Memory
- 16Mhz Clock Speed
- ATmega328
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 6
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 150 mA
- Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM
- 2 KB (ATmega328) EEPROM
- 1 KB (ATmega328)
- Clock Speed 16 MHz
-
-15%
Out Of StockArduino UNO R3 Enclosure Transparent Clear Case
Original price was: ₨350.00.₨299.00Current price is: ₨299.00. Quick View- To protect your little computer against damages, dust, and scratches Clear Top and Bottom.
- This case provides easy access to all ports
- It requires no tools for easy assembly and disassembly
- Simply Clicks Together Enclosure
- This case is a beautiful yet simple way to show off your UNO!
-
Hot-44%
Arduino UNO R3 SMD – Economic
Original price was: ₨1,500.00.₨839.00Current price is: ₨839.00. Quick ViewThe Arduino UNO R3 SMD Economic is a cost-effective microcontroller board powered by the ATmega328P. With 14 digital I/O pins, 6 analog inputs, and 16 MHz speed, it’s perfect for IoT, robotics, and electronics projects. Buy now from Electronation Pakistan at the best price with fast delivery nationwide.
-
Hot-33%
Arduino UNO R3 SMD – Economic WITH CABLE
Original price was: ₨1,500.00.₨999.00Current price is: ₨999.00. Quick View- ATmega328-AU microcontroller with UNO Bootloader Installed.
- USB Programming Facilitated by the CH340G.
- USB-B Connector and cable included.
- Input voltage – 7-15V.
- 0-5V outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).
- 6 Analog Inputs.
- ISP Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- All SMD Construction.
- R3 Shield Compatible
-
Out Of Stock- Based on TI CC3000 WIFI module.
- Use SPI communication .
- Integrated 3.3V regulator .
- Level shifter integrated .
- Integrated ceramic antenna .
- It has a connector for external antenna WIFI
- Compatible with Arduino UNO, Mega, Leondardo & Micro
- Antenna: Onboard Ceramic
- MicroSD card slot onboard
- Reset button
- Communication Protocol: SPI
- Connects via IEEE 802.11 b/g networks
- Tx Bandwidth: 11Mbps
- Tx Sensitivity: +/-18dBm
- Rx sensitivity: -86dBm
- IRQ pin for interrupts (useful for asynchronous connections)
- Supports WEP, WPA, WPA2, TKIP and AES
- TCP and UDP Client & Server Modes available
- Max Concurrent TCP/UDP Sockets: 4
- TCP/IP stack is built in.
-
-37%
AT-09 HM10 / HM-10 4.0 BLE Bluetooth Serial CC2540 CC2541 Module For IOS 6/Android 4.3
Original price was: ₨950.00.₨599.00Current price is: ₨599.00. Quick View- Ultra Low Standby Power 90uA ~ 400uA
- Communication Distance Range : 100 ft / 60mtr
- Super Fast Reaction Speed : 0.4 Sec.
- Built-in PCB antena
- Power Input : 3.6V To 6V DC (Cannot higher than 6V)
- Size : 43 X 15 mm
- Color : Blue
- Net weight : 4g
-
-13%
The AT89C52 is a lowe power, high performance CMOS 8-bit microcontroller with 8K bytes of Flash programmable and reaseable read only memory (PEROM). The on-chip flash allows the program memory to be reprogrammed in-syetem.
-
-20%
ATMEGA 328P ATMEGA328P-PU MICROCONTROLLER
Original price was: ₨1,500.00.₨1,199.00Current price is: ₨1,199.00. Quick ViewThe ATMEGA328P-PU is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega328P-PU achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.
The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU),allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers.The ATmega328P-PU AVR is supported with a full suite of program and system development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emulators, and Evaluation kits.
-
-27%
Atmega8 Microcontrollers IC 8Kbytes
Original price was: ₨899.00.₨659.00Current price is: ₨659.00. Quick ViewThe Atmel AVR ATmega8 is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8 achieves throughputs approaching 1MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed.
-
-8%
Atmel Attiny85 Attiny-85 ATtiny85-20PU
Original price was: ₨1,200.00.₨1,099.00Current price is: ₨1,099.00. Quick ViewFeatures of ATtiny85 Microcontroller:-
- Flash (Kbytes): 8 Kbytes
- Pin Count: 8
- Max. Operating Freq. (MHz): 20 MHz
- CPU: 8-bit AVR
- Number of Touch Channels: 3
- Hardware QTouch Acquisition: No
- Max I/O Pins: 6
- Ext Interrupts: 6
- USB Interface:No
- Package – SMD
-
It is a type of electrical connector typically used for analog audio signals.
-
-34%
Automatic Photocell Street Light Sun Switch Sensor 12V or 220V
Original price was: ₨600.00.₨399.00Current price is: ₨399.00. Quick View- Its color is white and blue.
- Its size is 5 x 4.2 x 3.3 cm.
- Its input voltages are AC 220V or DC 12V.
- Its maximum load current is 10A.
- Its frequency range is 50 to 60 Hz.
- It is widely used in street lighting, highways, factories, gardens, ports, airports, farms, parks, schools, and other places.
-
-20%
- 1m
- Male to Male.
- Stereo Audio Aux Extension Cable .
-
Out Of StockSupport for 51 series microcontroller STC89C52, STC12C5A60S2, AT89C51, AT89C52, AT89S51, AT89S52 most commonly used. In addition, to support the other 40 feet of the 51 series microcontroller and the ATmega16! STC89C52, STC12C5A60S2 can serial direct download program for, AT89S series microcontroller needs need specialized programming download program with USBISP a download manager program, AT89C series microcontroller. The ATmega16 use need to use an adapter plate, the download program needs USBISP Downloader!
-
-26%
- Banana Socket for Power Supply
- Round
- Female
- Socket
- Plug
- Connector
-
-29%
Banana clip female small used in power supply.
-
A banana connector is a single-wire electrical connector used for joining wires to equipment.
-
-47%
Battery Capacity Indicator DC 8V-100V Voltmeter Voltage Gauge 12V 24V 48V 72V
Original price was: ₨3,590.00.₨1,899.00Current price is: ₨1,899.00. Quick View- Item Type: Battery Monitor
- Material: ABS
- Display Color: Colored
- Voltage Measurement Range: DC8-80V
- Measurement Accuracy: 1% ± 1 word.
- Display: LCD screen
- Measurement Speed: about 2 times per second.
- Dimensions: Approx. 6.5 x 3.5 x 1.5cm / 2.6×1.4×0.6in
- Installation Size: Approx .58 x 28mm / 2.3×1.1in
- Lead Length: 20cm / 7.9in
-
-18%
Battery lugs are an important component to creating a solid connection between your battery cable and the battery that powers your electrical system. Buy best quality battery lugs from ElectroNation.
-
-22%
Battery lugs are an important component to creating a solid connection between your battery cable and the battery that powers your electrical system. Buy the best quality battery lugs from ElectroNation.
-
-33%
Out Of StockBattery Meter Checker Tester -7 Cell Capacity
Original price was: ₨1,500.00.₨999.00Current price is: ₨999.00. Quick ViewDigital Battery Capacity Checker Cellmeter 7
Compatible device: NiCd, NiMH, LiPo, LiFe, Li-ion
Use for LiPo LiFe Li-ion NiMH Nicd battery
Applies to check the batteries
2.1″ screen display
Battery Type: NiCd /NIMH, Li-Po, LiFe, Li-Ion
Cell number: NiCd/NIMH(4-7 Cells),Lithium type(2-7 Cells)
Display Mode: Battery cell voltages, total voltages, lowest cell voltage, Highest cell voltage gap between highest cell voltage and lowest cell voltage, Remaining battery capacity(%) -
-51%
Battery Protection Board 2s 8a Bms For 18650 Lithium Ion Cells Hx-2s-jh10
Original price was: ₨325.00.₨159.00Current price is: ₨159.00. Quick View- Model: HX-2S-JH10
- Size: 40*17*3.5mm
- Over-discharge voltage range: 2.5-3.0v±0.05v
- Overcharge voltage range: 4.25-4.35v±0.05v
- Upper limit working current: 8A
- Upper limit instantaneous current: 10A
- Working temperature: -40— 50 °C
- Storage conditions: -40– 80 ° C
- Quiescent current: less than 10uA
- Effective life: more than 50,000 hours
- Internal resistance: less than 300mΩ
- Charging voltage: 8.4V-9V
- Short circuit protection: protection, disconnect load delay self-recovery Solder join
-
-28%
- Small Signal NPN Transistor
- Current Gain (hFE): 450 (maximum)
- Continuous Collector current (IC) is 100mA
- Collector-Emitter voltage (VCEO) is 45V
- Collector-Base voltage (VCB0) is 50V
- Emitter Base Voltage (VBE0) is 6V
- Available in To-18 Metal can Package
-
- Bi-Polar NPN Transistor
- DC Current Gain (hFE) is 900 maximum
- Continuous Collector current (IC) is 200mA
- Emitter Base Voltage (VBE) is 5V
- Base Current(IB) is 10mA maximum
- Available in TO-18 Metal Can Package
- Maximum Collector-Base Voltage |Vcb|: 30 V’
- Collector Dissipation: 0.3 W
- Transition Frequency:150 MHz
- Operating Junction Temperature Max (Tj): 175 °C
- Noise Figure – 2 dB
- Operating and Storage Junction Temperature Range -65 to +175 °C
- Collector Capacitance 5pF
-
BC109 is a bipolar NPN type transistor. It has Collector-Emitter Volt (Vceo): 20V & Collector Current (Ic): 0.2A.
-
BC134 is a NPN type transistor. Its Maximum Collector-Base Voltage |Vcb|: 45 V & Maximum Collector Current |Ic max|: 0.2 A.
-
BC327 is a PNP bipolar junction transistor which is mainly designed for general purpose, small signal and switching applications.
-
This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The BC337 is specifically rated at 50V and 800mA max.
-
-40%
BC547-B166 NPN Transistor 50V/ 0.3A
Original price was: ₨15.00.₨9.00Current price is: ₨9.00. Quick ViewOverall, the BC547 NPN transistor is a versatile and reliable transistor that is suitable for a wide range of applications. NPN Transistor BC547 is a popular choice for electronic hobbyists and engineers because it is inexpensive and easy to use. here are the specifications of the BC547-B166 NPN transistor:
- Collector current (maximum): 300mA
- Collector-emitter voltage (maximum): 65V
- Base current (maximum): 5mA
- Current gain (hFE): 110 to 800
- Package: TO-92
-
- Bi-Polar NPN Transistor
- DC Current Gain (hFE) is 800 maximum
- Continuous Collector current (IC) is 500mA
- Emitter Base Voltage (VBE) is 5V
- Base Current(IB) is 5mA maximum
- Available in To-92 Package
-
- Package Type: TO-92
- Transistor Type: PNP
- Max Collector Current(IC): -100mA
- Max Collector-Emitter Voltage (VCE): -45V
- Max Collector-Base Voltage (VCB): -50V
- Max Emitter-Base Voltage (VBE): -5V
- Max Collector Dissipation (Pc): 500 Milliwatt
- Max Transition Frequency (fT): 100 MHz
- Minimum & Maximum DC Current Gain (hFE): 125 to 800
- Max Storage & Operating temperature Should be: -65 to +150Centigrade
-
- Plastic casing NPN Transistor
- Continuous Collector current (IC) is 1.5A
- Collector-Emitter voltage (VCE) is 80 V
- Collector-Base voltage (VCB) is 80V
- Base Current (Ib) is 0.5A
- Emitter Base Breakdown Voltage (VBE) is 5V
- DC current gain (hfe) is 40 to 160
- Available in To-225 package
-
- Bi-Polar PNP Transistor
- Continuous Collector current (IC) is -1.5A
- Collector-Emitter voltage (VCE) is- 80 V
- Collector-Base voltage (VCB) is- 80V
- Base Current (Ib) is -0.5A
- Emitter Base Breakdown Voltage (VBE) is -5V
- DC current gain (hfe) is 40 to 160
- Available in To-225 and SOT-32 Package
- Collector Dissipation: 12.5 W
- Operating Junction Temperature Max (Tj): 150°C
-
Hot-22%
Beginner Arduino Uno Starter Kit
Original price was: ₨8,999.00.₨6,999.00Current price is: ₨6,999.00. Quick ViewIn Pakistan, the Arduino Starter Kit Arduino Basic Kit Arduino Beginner Kit is the finest educational option for learning how to utilize the Arduino platform. It includes an Arduino Uno SMD board, an enhanced version of the R3, a variety of sensors and, Motor, led’s Dot-matrix, Lcd, and many other components required for the very first steps with electronics into the realm of interactive and sensing objects. The Arduino Starter Kit is an excellent present for children aged 9 to 99. The Arduino starter kit is an open-source electronics prototyping platform built on adaptable, user-friendly hardware and software. It includes all of the necessary components to begin programming with the Arduino Uno board.
-
-60%
Benetech GM-1352 Mini Sound Level Meter
Original price was: ₨15,000.00.₨5,999.00Current price is: ₨5,999.00. Quick View -
-38%
Benetech GM-1356 Digital Sound Level Meter (30-130 dB, USB Data Logging)
Original price was: ₨18,500.00.₨11,499.00Current price is: ₨11,499.00. Quick ViewThe Benetech GM-1356 is a professional digital sound level meter designed to measure noise levels accurately in the 30–130 dB range. With ±1.5 dB accuracy, A/C weighting, and Fast/Slow response modes, it’s perfect for factory noise testing, office compliance, and environmental monitoring.
This sound meter with USB data logging stores up to 4700 readings and connects directly to your PC for reporting. The backlit LCD display shows both digital readings and a bar graph, making it easy to track real-time noise levels.
Whether you need a noise meter for industrial sites in Karachi, office use in Lahore, or environmental testing in Islamabad, the GM-1356 delivers reliability at an affordable price in Pakistan.
-
-49%
Best Mini 5v DC Water Pump/Submersible Pump For Arduino
Original price was: ₨490.00.₨249.00Current price is: ₨249.00. Quick View- Operating Current : 130 ~ 220mA
- Operating Voltage : 2.5 ~ 6V
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Driving Mode : DC, Magnetic Driving
- Continuous Working Life : 500 hours
- Material: Engineering Plastic
- Outlet Outside Diameter: 7.5 mm
- Outlet Inside Diameter: 5 mm
-
-40%
Best Mini 5v DC Water Pump/Submersible Pump For Arduino
Original price was: ₨485.00.₨289.00Current price is: ₨289.00. Quick View- Operating Current: 130 ~ 220mA
- Operating Voltage: 2.5 ~ 6V
- Flow Rate: 80 ~ 120 L/H
- Maximum Lift: 40 ~ 110 mm
- Driving Mode: DC, Magnetic Driving
- Continuous Working Life: 500 hours
- Material: Engineering Plastic
- Outlet Outside Diameter: 7.5 mm
- Outlet Inside Diameter: 5 mm
-
- HF applications in radio and television receivers
- FM tuners
- Low noise AM mixer-oscillators
- IF amplifiers in AM/FM receivers
