Shop

  • You've just added this product to the cart:

    10 DOF IMU Sensor

    10 DOF IMU Sensor
    0 out of 5

    10 DOF IMU Sensor

    3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.

    ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.

    1,850.00
  • You've just added this product to the cart:

    10 DOF Mems IMU Sensor

    10 DOF Mems IMU Sensor
    0 out of 5

    10 DOF Mems IMU Sensor

    INTRODUCTION

    At the beginning,the inertial measurement unit is an electronic device that measures and reports on a craft’s velocity, orientation, and gravitational forces, using a combination of accelerometers,gyroscopes, and magnetometers. Now IMUs are commonly used in the Human-computer interaction(HCI), navigational purposes and balancing technology used in the Segway Personal Transporter as we all known.
    The 10 DOF(degrees of the freedom) sensor is a compact and low cost IMU from DFRobot. It integrates the ADXL345 accelerometer, the HMC5883L magnetometer,the ITG-3205 gyro and the BMP085 barometric pressure sensor. It’s suitable for most of the controlling system because of the small dimension. The mounting holes make it possible to provide the highly accurate and stable sensor data.It embeds a low noise LDO regulator for supplying a wide range power input.Works with 3~8 volts power input.Certainly,the 10 DOF sensor is directly compatible with your Arduino boards.

    4,200.00
  • You've just added this product to the cart:

    100K Potentiometer (Pot)

    0 out of 5

    100K Potentiometer (Pot)

    A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element.The position of the wiper determines the output voltage of the potentiometer. small screw driver can be used for calibration of resistance value.

  • You've just added this product to the cart:

    100mm Aluminum Double Omni wheel with bearing rollers

    100mm Aluminum Double Omni wheel with bearing rollers
    0 out of 5

    100mm Aluminum Double Omni wheel with bearing rollers

    These aluminum omni wheels are made up of 2 aluminum plates with some rollers mounted around the outer circumference. Each roller is attached with two bearings to give the smoothest rolling. These rollers allow the omni wheel to travel sideways with no skidding during turns. As an omni-directional wheel, it can travel in more than one direction, as well as 360° movement with rotation. When the axle spins, it behaves like a normal wheel.

    4,150.00
  • You've just added this product to the cart:

    1045 PROPELLER CW/CCW

    1045 PROPELLER CW/CCW
    0 out of 5

    1045 PROPELLER CW/CCW

    10×4.5″ 1045 1045R Counter Rotating Propeller For MultiCoptor available in all colors.

    150.00
  • You've just added this product to the cart:

    1080P Full HD H.264 Waterproof Sports Camera

    1080P Full HD H.264 Waterproof Sports Camera
    0 out of 5

    1080P Full HD H.264 Waterproof Sports Camera

    Extreme Sports, Outdoor Sport Activities,Bicycle,Car DVR, Diving,Home security etc.
    Features:

    1. Video recording while charging
    2. 12-megapixel HD wide-angle lens
    3. HDMI HD output
    4. Web camera
    5. Support storage cards up to 32GB maximum
    6. Recorded in MOV format
    7. Multiple photo shooting modes: Single shot, Snapper
    8,500.00
  • You've just added this product to the cart:

    10K Potentiometer (Pot)

    0 out of 5

    10K Potentiometer (Pot)

    A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element.The position of the wiper determines the output voltage of the potentiometer. small screw driver can be used for calibration of resistance value.

  • You've just added this product to the cart:

    12 V Door Lock

    -28%
    0 out of 5

    12 V Door Lock

    It is an electromagnetic door lock. It creates an magnetic field when energised causing the electromagnet and the armature attract each so tightly that the door can’t be open until deenergized.

    250.00 180.00
  • You've just added this product to the cart:

    12V DC Motor 350RPM w/Encoder (12kg*cm)

    12V DC Motor 350RPM w/Encoder (12kg*cm)
    0 out of 5

    12V DC Motor 350RPM w/Encoder (12kg*cm)

    This is a gear motor with encoder. It is a motor with a 34:1 gearbox and an integrated quadrature encoder that provides a resolution of 11 pulse single per round giving a maximum output of 374 within one round. With an Arduino controller and motor driver, applications for this include a closed-loop PID control or PWM motor speed control. This motor is an ideal option for mobile robot projects. The copper output shaft, embedded thread and reinforced connector greatly extends the motor’s service life.

    3,000.00
  • You've just added this product to the cart:

    16 Channel Relay Module

    0 out of 5

    16 Channel Relay Module

    The 16 channel relay module is an interface board which has the ability to control various appliances and equipments due to its relays module. Every input of the board is isolated through a photocoupler. This is easy to use and can be controlled through any microcontroller board like Arduino, 8051, PIC etc. These relays are active on low level signal on each control pin and 16 LEDs indicates the status of these 16 relays.

  • You've just added this product to the cart:

    17DOF Humonoid Robot

    17DOF Humonoid Robot
    0 out of 5

    17DOF Humonoid Robot

    Body with hard alloy as a skeleton, very light and strong! Graphical programming, easy to learn, it can bipedal walking, tumbling, choreography, full of fun! Applicable to all types of robot dance, racing games, you can also participate in various large-scale activities to do robot.

    21,000.00
  • You've just added this product to the cart:

    18B20 Temperature Module

    18B20 Temperature Module
    0 out of 5

    18B20 Temperature Module

    These 3-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontroller using a single digital pin, and you can even connect multiple ones to the same pin, each one has a unique 64-bit ID burned in at the factory to differentiate them. Usable with 3.0-5.0V systems.

    275.00