-
-19%
G2R is a power relay with a coil rated voltage of 6V. The relay have 5 pins, with good quality and long operational life.
-
Out Of StockThis IC is a 16-Bit SPI I/O Expander with Serial Interface. This IC has 25mA sink/source capability per I/O.
-
The 4N25 is an optocoupler for general purpose applications. It contains a light emitting diode optically coupled to a photo-transistor.
-
- Reverse Voltage(Vr): 5 V
- Reverse Leakage Current (Ir): 50A
- Forward Current (If): 25mA
- Peak Forward Current (Ifp): 100 mA
- Power Dissipation (P): 100 mW per Segment
- Operating Temperature (Topr): -40C to +80C
- Storage Temperature (Ttsg): -40C to +85C
- Lead Soldering Temperature: 260C
- Height: 70mm
- Width: 48mm
-
Resistors are electronic components which have a specific, never-changing electrical resistance. The resistor’s resistance limits the flow of electrons through a circuit. They are passive components, meaning they only consume power (and can’t generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.
-
-24%
Hi Flow Soldering Wire (100gm)
Original price was: ₨590.00.₨449.00Current price is: ₨449.00. Quick ViewSoldering wire is used for creating a robust connection between two wires or to join electronic components of all kinds to a printed circuit board. This soldering wire is of 100 gm.
-
- Screw Drive Tester
- Best for Electric Work
- High Quality
- Low Voltage
- Multicolour
-
-37%
- Rated Load: 20Kg
- Rated Output: 1.0 ±0.15mV/V
- Zero Output: ±0.1mV/V
- Cree: 0.03%F.S./30min
- Input End: Red+, Black-
- Output End: Green+, White-
- Input Impedance: 1115±10% Ω
- Output Impedance: 1000±10% Ω
- Maximum working voltage: 15V DC
- Operating temperature range: -20~60°C
- Total Size: 80 x 13 x 13mm/3.14 x 0.51 x 0.51″(L x W x H)
-
- Input levels: CMOS level
- 16-line demultiplexing capability
- Decodes 4 binary-coded inputs into 16 mutually-exclusive outputs
- Complies with JEDEC standard no. 7 A
- ESD protection: HBM JESD22-A114F exceeds 2000 V MM JESD22-A115-A exceeds 200V
- Multiple package options
- Specified from -40C to +85C and -40C to +125C
-
- N-Channel Power MOSFET
- Continuous Drain Current (ID): 8A
- Gate threshold voltage (VGS-th) is 10V (limit = 20V)
- Drain to Source Breakdown Voltage: 500V
- Drain Source Resistance (RDS) is 0.85 Ohms
- Rise time and fall time is 23nS and 20nS
- Available in To-220 package
-
-34%
5v 2A Adapter Power Adapter 5V 2000mA
Original price was: ₨600.00.₨399.00Current price is: ₨399.00. Quick ViewPower adapter output rating is 5 volts and 2000 mili amperes.
Input
100-240V AC 50/60HzOutput
DC 5V 2A(max)Power
10WattCable Cord Length
6.5Ft (2m)Color
Black -
-39%
NODEMCU LUA WIFI BOARD BASED ON ESP8266 CP2102 MODULE
Original price was: ₨1,099.00.₨669.00Current price is: ₨669.00. Quick View- Wi-Fi Module The ESP-12E module is similar to the ESP-12 module but with 6 extra GPIOs.
- USB micro USB port for power, programming, and debugging
- Headers 2x 2.54mm 15-pin header with access to GPIOs, SPI, UART, ADC, and power pins
- Misc Reset and Flash buttons
- Power 5V via micro USB port
- Dimensions 49 x 24.5 x 13mm
-
-17%
1 Support WINDOWS 98 / ME / 2000 / XP / Server 2003 / VISTA /Server 2008 / Win7 / Win8 32 Bit / 642. Support USB1.1 or USB2.0/USB3.0 for communication.3. Simulation interface, you can upgrade serial peripherals.4. Supports common MODE contact signal.5. Supports IRDA SIR infrared communication.6.information download here7. Provide RS232, RS485, RS422 interface.8. Programming does not affect the target board program runs -
-10%
Arduino SD Card Reader Module
Original price was: ₨220.00.₨199.00Current price is: ₨199.00. Quick View- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V\
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
-
-25%
- Built-in USB to RS232 Transfer chip.
- Designed to be used for USB to TTL electronic projects.
- TTL interface output, easy to connect to your MCU.
- Status LED.
- Dual 3.3V and 5V Power output, work with 3.3v and 5v target device.
- Compact design.
- Dimension: 42 mm x 17 mm
-
-17%
DHT11 Temperature and Humidity Sensor
Original price was: ₨300.00.₨249.00Current price is: ₨249.00. Quick View- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0C to 50C
- Humidity Range: 20% to 90%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: 1C and 1%
-
-33%
SIM800L GSM Module Micro Sim Card Board
Original price was: ₨1,799.00.₨1,199.00Current price is: ₨1,199.00. Quick View- Module models: SIM800L (latest module, performance than SIM900)
- Operating voltage: 3.7 to 4.2 V (peak current is 2A)
- Support network: China mobile, China Unicom
- Module size: 2.2 x 1.8cm
- TTL serial port can directly link to MCU. Don’t need a MAX232
- Power on automatic startup, automatic search network
- Onboard one channel indicator light (with signal slow flash, no signal quickly flash)
-
-41%
- Working voltage: DC 3.3V-5V
- Working current: 20mA
- Operating temperature: -10~+50
- detection distance :2-40cm
- IO Interface: 4-wire interfaces (-/+/S/EN)
- Output signal: TTL level (low level there is an obstacle, no obstacle high)
- Adjustment: adjust multi-turn resistance 8. Effective angle: 35.7.
- Size: 28mmx23mm
-
-26%
- Material: FR4
- Length: 25mm
- Width: 11mm
- Height: 16mm
- Weight: 1.59g
- Operating Voltage: 5v DC
-
-36%
- Content: 460 g
- Color: Black/Gray
- Price: Inclusive of All taxes
- 5 minutes jointing
-
-15%
This device contains four independent gates each of which performs the logic exclusive-OR function.
-
-6%
TB6600 Arduino Stepper Motor Driver 4A, 5A
Original price was: ₨1,800.00.₨1,699.00Current price is: ₨1,699.00. Quick View- This stepper motor driver supports 8 kinds of current control.
- This stepper driver supports 7 kinds of micro-steps adjustable.
- Stepper motor driver interface adopts high-speed optocoupler isolation.
- It has the feature of automatic semi-flow to reduce heat.
- It has a large area heat sink.
- It has anti-high-frequency interference ability.
- It has input anti-reverse protection
- It has the feature of overheating, over-current, and short circuit protection.
-
-7%
- Model: YF-S201
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Liters/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Liter: 450
- Durability: minimum 300,000 cycles
- Cable length: 15cm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 2.5″ x 1.4″ x 1.4″
-
-47%
- Its model is ESP-12F.
- Its package is SMD22.
- Its size is 24 x 16 x 3 (+- 0.2)mm.
- Its certification is from FCC, CE,C,REACH,RoHS.
- It has default 32Mb SPI flash.
- It has a UART/ADC/GPIO/PWM interface.
- It has 9 input-output ports.
- It supports 300-4608000 bps and default 115200 bps UART baud rate.
- Its frequency range is 2412- 2484 MHz.
- It has a PCB antenna.
- Its power value is 500mA.
- Its modem sleep value is -20mA.
- Its light sleep value is -2mA.
- Its deep sleep value is -0.02mA.
- Its security is WEP/WPA-PSK/WPA2-PSK
- Its power supply voltages are 3 to 3.6V.
- Its current value is >500mA.
- Its operating temperature is -20 to 85-degree centigrade.
- Its storage environment is -40 to 85-degree centigrade.
- Its default baud rate is 115200.
- It has a TTL serial port level.
-
-17%
- Resistance: 203 20K Ohm,
- Resistor Tolerance: ±10% Max
- Max Voltage: 50V
- Rating Power: 0.1W
- Technology: Carbon Film
- Adjustment Type: Top Adjustment
-
- Package Type: TO-92
- Transistor Type: NPN
- Max Collector Current(IC): 30mA
- Max Collector-Emitter Voltage (VCE): 20V
- Max Collector-Base Voltage (VCB): 30V
- Max Emitter-Base Voltage (VBE): 5V
- Max Collector Dissipation (Pc): 300 Milliwatt
- Max Transition Frequency (fT): 120 MHz
- Minimum & Maximum DC Current Gain (hFE): 35 to 125
- Max Storage, Operating & Junction temperature range: -65 to +150 Centigrade
-
-20%
2SA1941 bipolar transistor p-n-p type transistor. Collector-Emitter Voltage: -140 V Collector-Base Voltage: -140 V Emitter-Base Voltage: -5 V Collector Current: -10 A Collector Dissipation – 100 W DC Current Gain (hfe) – 55 to 160 Transition Frequency – 30 MHz Operating and Storage Junction Temperature Range -55 to +150 ?C
-
-13%
- 24V Positive Voltage Regulator
- Minimum Input Voltage is 33V
- Maximum Input Voltage is 40V
- Output Current: 1.5 A
- Internal Thermal Overload and Short circuit current limiting protections are available.
- Junction Temperature maximum of 125 degree Celsius
- Available in TO-220, TO-3 and KTE package
-
-13%
- Output voltage tolerances of ±2% at Tj = 25˚C and ±4% over the temperature range (LM340A)
- Line regulation of 0.01% of VOUT/V of ∆VIN at 1A load (LM340A)
- Load regulation of 0.3% of VOUT/A (LM340A)
- Internal thermal overload protection
- Internal short-circuit current limit
- Output transistor safe area protection
- P+ Product Enhancement tested
-
- Seven Darlingtons per package
- Output current 500 mA per driver (600 mA peak)
- Output voltage 50 V
- Integrated suppression diodes for inductive loads
- Outputs can be paralleled for higher current
- TTL/CMOS/PMOS/DTL compatible inputs
- Inputs pinned opposite outputs to simplify
-
ULN 2803 is a high-voltage, high-current Darlington transistor array. The device consists of eight npn Darlington pairs that feature high-voltage outputs with common-cathode clamp diodes for switching inductive loads. The collector-current rating of each Darlington pair is 500 mA. The Darlington pairs may be connected in parallel for higher current capability. Applications include relay drivers, hammer drivers, lamp drivers, display drivers (LED and gas discharge), line drivers, and logic buffers.
-
- Carries Low input bias current = 50 pA
- Available with Low input noise current = 0.01 pA/Hz
- Comes with Fast settling time to 0.01% = 2us
- Contains internally trimmed offset voltage = 15 mV
- Carries Low input noise voltage = 16nV/Hz
- Exhibits Low supply current = 3.6 mA
-
-27%
4N35 optocoupler consists of gallium arsenide infrared LED and a silicon NPN phototransistor.Isolation test voltage 5000 VRMS. Input-output coupling capacitance < 0.5 pF . 4N35 optocoupler consists of gallium arsenide infrared LED and a silicon NPN phototransistor.Isolation test voltage 5000 VRMS. Input-output coupling capacitance < 0.5 pF . 4N35 optocoupler consists of gallium arsenide infrared LED and a silicon NPN phototransistor.Isolation test voltage 5000 VRMS. Input-output coupling capacitance < 0.5 pF .
-
-17%
LM386 LM-386 Audio Amplifier Chip
Original price was: ₨35.00.₨29.00Current price is: ₨29.00. Quick ViewLM386 is a widely used audio amplifier IC manufactured in 8 pin dip, VSSOP, SOIC and other packages. The IC is basically designed for low voltage commercial applications, apart from commercial applications it is also a famous IC among electronic hobbyists and experimenters. The internal gain of the IC is set to 20 but it can be adjusted by connecting a resistor and a capacitor in series between the pin number 1 and 8, by this procedure the user can adjust the gain between 20 to 200. Due to the small size, low quiescent current and low voltage requirements this IC is ideal to use in wide variety of portable battery operated applications and devices.
-
-20%
Lithium Battery 12V 2.2 Amp 2200mah With BMS
Original price was: ₨1,500.00.₨1,199.00Current price is: ₨1,199.00. Quick View- A 12V and 2.2A rating battery with a Battery Management system to have balanced charging and discharging through every cell of the battery.
- It’s a universal/multipurpose battery also used as WIFI routers, Power Bank, ETC.
- You can also customize lithium batteries as per your requirements.
-
-8%
Out Of StockLiPo 11.1V 3S 2200mAH
Original price was: ₨6,000.00.₨5,499.00Current price is: ₨5,499.00. Quick View- Name: LiPo Battery
- Quantity: 1 Piece
- Capacity: 2200mAh
- Type: Lithium Polymer
- Voltage: 11.1V/3S
- Burst Rate : 25C
- Continuous discharge rate: 25C
- Cells : 3
- Size : 85 x 40 x 27 mm
- Weight: 180g
- Max Burst Discharge: 60C
- Charge Voltage: 12.6V
- Discharge Plug: T Plug, Balance charger plug
-
-20%
DHT11 Humidity & Temperature Sensor
Original price was: ₨350.00.₨280.00Current price is: ₨280.00. Quick View- Dimension 28mm*12mm*10mm
- Main chip DHT11 huminity sensor
- Voltage: DC 5V
- Digital output
- Humidity Range: 2090%RH
- Humidity accuracy:5%RH
- Temperature range:0-60
- Temperature accuracy: 2
-
-41%
Out Of StockDALY 4S 12V 50A BMS with NTC Sensor – Advanced LiFePO4 Battery Protection Board
Original price was: ₨8,000.00.₨4,699.00Current price is: ₨4,699.00. Quick View- Model Number: DL4S
- For LiFePO4 Battery Pack
- Battery series: 4S
- Temperature Sensor: Yes
- Overcharge protection: Yes
- Over-discharge voltage: Yes
- Short circuit protection: Yes
- Balance function: Yes
- Accessory: Free cable
- Water proof: Yes
-
-28%
Out Of StockDigital Clamp Meter CM-550A
Original price was: ₨11,500.00.₨8,299.00Current price is: ₨8,299.00. Quick View- True RMS for accurate readings
- Auto range for ease of use
- NCV (Non-Contact Voltage Detection) for safety
- Live wire test & continuity check for diagnostics
- Diode testing & MAX/MIN recording
- Relative & Zero mode for precise comparisons
- Data hold & low battery indication
- Auto power-off for energy efficiency
-
-31%
50A SCT-013-000 Non-invasive AC Current Clamp Sensor
Original price was: ₨1,800.00.₨1,249.00Current price is: ₨1,249.00. Quick View- Input Current: 0~50A AC
- Output Mode: DC 0~1V
- Non-linearity：2-3%
- Build-in sampling resistance（RL): 62Ω
- Turn Ratio: 1800:1
- Resistance Grade: Grade B
- Work Temperature: -25°C ~ ﹢70°C
- Dielectric Strength(between shell and output): 1000V AC/1min 5mA
- Leading Wire in Length: 1m
- Open Size: 13mm x 13mm
-
-24%
7 in 1 Soil Integrated Sensor EC PH NPK Moisture Temperature Meter
Original price was: ₨38,000.00.₨28,999.00Current price is: ₨28,999.00. Quick View- High precision agriculture sensors, rapid response, good exchange ability
- Good tightness, corrosion resistance, the soil tester can be used in the soil for a long time.
- Flame retardant epoxy resin curing, completely waterproof, the soil tester can withstand strong external impact.
- Steel needles are made of high quality materials that can with stand long-term electrolysis , acid and alkali corrosion in soil.
-
-24%
Goot 40W Soldering Iron KS-40R
Original price was: ₨1,050.00.₨799.00Current price is: ₨799.00. Quick View- Manufacturer: Goot
- Model: KS-40R
- Color: Blue
- Material: ABS
- Power: 40W
- Working Voltage: AC220V / 50Hz
- Soldering Iron Length: Approx. 32cm
- Power Cord Length: Approx. 123cm / 48.43in
- Item Weight: Approx. 50g
- Package Weight: Approx. 134g / 4.71oz
-
-11%
LED SMD Strip 5m Size In Red Color
Original price was: ₨899.00.₨799.00Current price is: ₨799.00. Quick View- Working Voltage: DC12V
- LED Type: SMD5050/SMD2835
- LED Quantity: 60leds/m, 120leds/m, 5 meters/rollWidth : 8mm (SMD2835) /10mm (SMD5050)
- Protection Rate : Waterproof IP65 /Non waterproof IP20
- Color: Red
- Is Dimmable: Yes (dimmer switch required, but not included)
- Is Trimmable: Yes (cuttable every three LEDs)
- View angle: 120~140
- Working Temperature: -20C to 50 C
-
-32%
Acrylic Rectangle 0.56 Inch 3 Digit 7 Segment Display
Original price was: ₨130.00.₨89.00Current price is: ₨89.00. Quick View- Operating current: 10mA
- Bright Red LED chip, which is made from AlGaAs on GaAs substrate
- Low Current Consumption
- High Brightness
- Blackface and RED LED segments
-
-29%
4 Bits TM1637 Digital Tube LED 7 Segments Display Module
Original price was: ₨350.00.₨249.00Current price is: ₨249.00. Quick View4 Bits TM1637 Digital Tube LED 7 Segments Display Module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.
-
-20%
Out Of StockPiezoelectric Shock Tap Sensor Vibration Switch Module
Original price was: ₨899.00.₨715.00Current price is: ₨715.00. Quick View- Item Name: Piezoelectric Shock Tap Sensor Vibration Switch Module
- Item Type: Vibration Switch Sensor Module
- Working Voltage: 5.0V (DC)
- Interface Type: AD/DO
- AO: Analog Signal Output
- DO: TTL Level Output
- Working Temperature: -10 C ~ +70 C
- Size: Approx. 20 x 20mm / 0.8 x 0.8in
- Weight: 4.5 g / 0.2 oz(approx.)
- Test Method and Wiring:
- G (GND):: Power ground
- V (VCC): Operating voltage 5V (DC)
- ADO: Analog signal output
- According to the vibration intension, the higher the output voltage, the higher the vibration amplitude sensitivity can be adjusted by the potentiometer (the left turn sensitivity is low, the right turn sensitivity is high). The high sensitivity output can be adjusted to respond with a mouth blow or a tap with a hand.
- DO: TTL level output. Output signal LED indication. TTL output valid signal is high level, output control power
-
-41%
MAX31865 RTD PT100 Amplifier
Original price was: ₨2,700.00.₨1,599.00Current price is: ₨1,599.00. Quick View- Advantage: Handling all of your RTD needs.
- Strong point: Compensating 3 or 4-wire RTDs for better accuracy.
- Characteristic: Could be used with any Arduino or microcontroller.
- Feature: 3.3V regulator and level shifting.
- Feature: Could be used with any 2, 3, or 4-wire PT100 RTD.
-
-18%
Pack of 5 27mm Piezo Electric Plate
Original price was: ₨400.00.₨330.00Current price is: ₨330.00. Quick View- Product type: Piezoelectric Transducer Piezo Sensor
- Colour: copper and silver
- Dimension: 27 mm
- Weight: 2 g
- Sheet material: bronze
- Package contains: 1 x piezoelectric sensor