• The main use is for audio frequency amplifier applications. It can also be used for the switching purpose just like other PNP transistors. When use as an Audio frequency general purpose amplifier, can be operated in the active region. This transistor is further divided into four groups according to the DC current gain, O, Y, G, and L and has 140, 240, 400 and 700 hfe DC current gain respectively.

  • -23%

    A2212 – 1400KV BLDC Brushless Motor

    (0)
    Original price was: ₨1,999.00.Current price is: ₨1,549.00. Quick View
    • KV: 1400
    • No-load Current : 10 V : 0.5 A.
    • Current Capacity: 12A/60s
    • No Load Current @ 10V: 0.5A
    • No. Of Cells: 2-3 Li-Poly
    • Motor Dimensions: 27.5 x 30mm
    • Shaft Diameter: 934;3.17mm
    • Shaft diameter: 3.175mm.
    • Minimum ESC Specification: 18A (30A Suggested)
    • Thrust @ 3S with 1045 propeller: 1000gms approx.
    • Thrust @ 3S with 0945 propeller: 650gms approx.
    • Thrust @ 3S with 0845 propeller: 550gms approx
  • -23%

    A2212 1000KV Brushless DC Motor

    (0)
    Original price was: ₨1,999.00.Current price is: ₨1,549.00. Quick View
    • Model: A2212 10T
    • Motor KV (RPM/V): 1400
    • Maximum Efficiency: 80%
    • Current Capacity: 16A Per 60S
    • No-Load Current(A): 0.7A @10V
    • Max. Efficiency Current: 6-12A
    • Maximum Watts(W): 180
    • Internal Resistance(mΩ): 65
    • Poles: 14
    • Shaft Diameter (mm): 3.17
    • LiPO Batteries: 2S-3S
    • Length (mm): 27.5
    • Width (mm): 26.5
    • Weight (gm): 62
  • -14%

    A2212 2200KV Brushless DC Motor BLDC

    (0)
    Original price was: ₨1,800.00.Current price is: ₨1,550.00. Quick View
    • Recommended Voltage: 2-12VDC
    • Internal Resistance: 90mΩ
    • Shaft Size: 3.17mm (1.8″)
    • Shaft Length: 11mm
    • Motor Diameter: 27.5mm
    • Motor Length (Overall): 40mm
    • Current Capacity: 12A/60s
    • Max Efficiency: 80%
    • Max Power: 239W
    • Recommended ESC: Minimum Of 18A
    • Recommended Model Weight: 300-1000g
    • Mounting Holes: M3
    • Wire Length: ~70mm
  • -10%

    A3967 Stepper Motor Driver Module

    (0)
    Original price was: ₨400.00.Current price is: ₨360.00. Quick View

    This EasyDriver compatible stepper motor driver module utilizes the Allegro A3967SLB micro-stepping driver to proved a simple and compact means of driving bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors from a microcontroller. By default, the module will accept a 5V TTL step and direction signal from the microcontroller to stop the motor in either full, half, quarter, and eighth-step modes. By shorting jumper SJ2 it can also be configured to be compatible with 3.3V microcontrollers that are not 5V tolerant. An onboard potentiometer allows for setting maximum drive current.

  • -23%

    A4988 Stepper driver

    (1)
    Original price was: ₨350.00.Current price is: ₨269.00. Quick View
    1. Supply Voltage : 8-35 VDC.
    2. Current : 1.0A (no heatsink ).
    3. Current : 2.0A (with heat-sinking).
    4. logic input : 3 – 5.5V .
    5. Automatic current decay mode detection/choice.
    6. Mixed with slow current decay mode.
    7. The low power dissipation of synchronous rectifier.
    8. Internal UVLO(ultra voltage lockout).
    9. Crossover current protection.
    10. Thermal shutdown circuit.
    11. Ground fault protection.
    12. Loading and short circuit protection.
    13. The optional five-step mode: full, 1/2, 1/4, 1/8 and 1/16.
  • AA 2Cell holder especially design for student science project kit and many more application in 3 volt supply.

  • AA 4 Cell Battery Holder Need 6V 1.5V cell or 4.8V with 1.2V cell to run a project on AA batteries This is a simple battery holder that we use in some of our kits. What we like about these are the leads that come pre-attached, ready to be soldered to a PCB, or attached with your choice of connector.

    1. Two mounting holes to accept flush head screws.
    2. You can also use high adhesive double-sided tape, or a glue gun to attach to your project or prototype.
    3. This battery holder has two wires 6 inches of 24-gauge leads that have 5 mm of insulation stripped off of the ends.
  • -45%

    ABS Enclosure Black Case for Raspberry Pi with Heat Sink And 5v Fan

    (0)
    Original price was: ₨2,000.00.Current price is: ₨1,099.00. Quick View

    This Raspberry case is made of ABS material. It can be perfectly compatible with Raspberry Pi 4B. Considering the high power consumption cost of Raspberry Pi 4B, the Raspberry case has room to add a fan (35x35x10mm) and general copper/aluminum heatsink (up to 6mm) for heat dissipation. What’s more The case supports the GPIO PINs of the Raspberry Pi 4B and connects external devices like Raspberry Pi Hat outside the case by cables. Also, the ventilation openings are designed on the top and bottom of the case to keep cooling.

  • -12%
    Out Of Stock

    AC 220V 100W Aluminum PTC Heater Thermostat Plate

    (0)
    Original price was: ₨1,700.00.Current price is: ₨1,499.00. Quick View

    Items details AC 220V 100W Aluminum PTC Heater Thermostat Heating Plate constant temperature basic parameter: PTC heater size: 67*70*6mm AC 220 volts 100 watts,250-260 degree Celsius automatic constant temperature.

  • -29%

    AC 220V Temperature Controller RKC REX-C700

    (1)
    Original price was: ₨3,500.00.Current price is: ₨2,499.00. Quick View
    1. Type: Digital
    2. Theory: Temperature Controller
    3. Usage: Industrial
    4. Model Number: REX-C700 Power
    5. Type: Charger Display
    6. Size:1.9 Inches & Under Max
    7. Measuring Temperature:120°C & Above
    8. Style: Standing Station
    9. Size:72*72mm
    10. Input: Universal Control
    11. output: Relay Alarm
    12. Display: Celsius °C Unit
    13. Type: piece
    14. Package Weight: 0.4kg (0.88lb.)
  • -40%
    AC/DC 60W Ceiling Fan Circuit Kit with Remote Control – BLDC Solar Fan Controller Board 12V 220V

    AC/DC 60W Ceiling Fan Circuit Kit | Solar & BLDC Fan Controller

    (0)
    Original price was: ₨2,500.00.Current price is: ₨1,499.00. Quick View
  • -20%
    ACEBOTT QE005 micro:bit Smart Home IoT Starter Kit in PakistanACEBOTT smart home STEM kit with micro:bit board

    ACEBOTT QE005 micro:bit Smart Home IoT Starter Kit

    (0)
    Original price was: ₨25,000.00.Current price is: ₨19,999.00. Quick View

    Bring coding, sensors, and real-world smart home projects together with the ACEBOTT QE005 micro:bit Smart Home IoT Starter Kit. Ideal for students, STEM classrooms, makers, and robotics labs, this kit includes the micro:bit board and supports Arduino and ACECode (Scratch) for hands-on learning. Students can explore alarms, motion sensing, touch-controlled lighting, emoji display, music effects, and LCD monitoring for temperature, humidity, and gas detection through guided project-based activities.

  • -20%
    ACEBOTT QE023 Easy-Plug ESP32 Smart Home Education Kit Level 13-in-1 smart home STEM kit with ESP32 for classroom learning

    ACEBOTT QE023 Easy-Plug ESP32 Smart Home Education Kit Level 1

    (0)
    Original price was: ₨30,000.00.Current price is: ₨23,999.00. Quick View

    Buy the ACEBOTT QE023 Easy-Plug ESP32 Smart Home Education Kit Level 1 from Electronation Pakistan and bring real-world STEM learning into the classroom. This 3-in-1 smart home education kit helps students build intelligent lighting, intelligent entertainment, and temperature & humidity control projects while learning coding, electronics, and IoT concepts with an ESP32 platform.

  • -32%
    Acrylic Rectangle 0.56 Inch 3 Digit 7 Segment Display

    Acrylic Rectangle 0.56 Inch 3 Digit 7 Segment Display

    (0)
    Original price was: ₨130.00.Current price is: ₨89.00. Quick View
    • Operating current: 10mA
    • Bright Red LED chip, which is made from AlGaAs on GaAs substrate
    • Low Current Consumption
    • High Brightness
    • Blackface and RED LED segments
  • -6%

    ACS712 Current Sensor 20A

    (0)
    Original price was: ₨350.00.Current price is: ₨329.00. Quick View
    1. Module Dimensions: 31 x 13 x 14 mm (LxWxH)
    2. Weight: 3 gm.
    3. Supply Voltage: 4.5V~5.5V DC
    4. Measure Current Range: -20A~ 20A
    5. Sensitivity: 100mV/A
    6. The current sensor chips: ACS712_ELC-20A.
    7. Pin 5V power supply, onboard power indicator.
    8. There is no the detection current through, the output voltage is VCC / 2.
    9. The module can be measure plus or minus 20 amps, corresponding to the analog output of 185 mV / A.
  • -10%
    Out Of Stock

    ACS712 Current Sensor 30A

    (0)
    Original price was: ₨400.00.Current price is: ₨359.00. Quick View

    ACS712 Current Sensor 30A current sensor board is based on the Allegro ACS712ELCTR-30A bi-directional hall-effect current sensor chip that detects positive and negative flowing currents in the range of minus 30 Amps to positive 30 Amps. The board operates at 5V DC and the current flow through the sensor is converted to an output voltage starting at 1/2Vcc (or 2.5V) for no current flow and moves up 66mV per amp for positive current or down -66mV per amp for negative current.

  • -7%

    ACS712 Current Sensor 5A

    (0)
    Original price was: ₨320.00.Current price is: ₨299.00. Quick View
    1. Module Dimensions: 31 x 13 x 14 mm (LxWxH)
    2. Weight: 3 gm.
    3. Supply Voltage: 4.5V~5.5V DC
    4. Measure Current Range: -5A~ 5A
    5. Sensitivity: 66mV/A
    6. The current sensor chips: ACS712_ELC-05B.
    7. Pin 5V power supply, onboard power indicator.
    8. There is no the detection current through, the output voltage is VCC / 2.
  • -36%
    • Diameter: 0.031″ (0.8mm)
    • Weight: 0.11lbs (50g) or (100g)
    • Composition: 70% Tin, 30% Lead
    • Rosin Flux Content: 2%
  • -40%
    Out Of Stock
    • Voltage Range: AC 80.0-300.0V
    • Current Range: AC 0-99.99A (0.01A resolution)
    • Power Factor: 0.00-1.00PF
    • Active Power Range: 0-45,000W
    • Energy Measurement: 0-99,999kWh
    • Operating Temperature: -25°C to 85°C
    • Dimensions: 79 x 43 x 48mm
  • -19%
    Out Of Stock

    AD7528 DAC IC

    (0)
    Original price was: ₨72.00.Current price is: ₨58.00. Quick View

    The AD7528 is a monolithic dual 8-bit digital/analog converter featuring excellent DAC-to-DAC matching. It is available in skinny 0.3″ wide 20-lead DIPs and in 20-lead surface mount packages. Separate on-chip latches are provided for each DAC to allow easy microprocessor interface.

  • -10%
    Out Of Stock

    Adjustable Soldering Iron 80W 220V/110V LCD Digital Display

    (0)
    Original price was: ₨2,000.00.Current price is: ₨1,799.00. Quick View
  • -32%

    ADS1115 Analog-to-Digital Converter

    (1)
    Original price was: ₨1,100.00.Current price is: ₨749.00. Quick View
    • WIDE SUPPLY RANGE: 2.0V to 5.5V
    • LOW CURRENT CONSUMPTION: Continuous Mode: Only 150µA Single-Shot Mode: Auto Shut-Down
    • PROGRAMMABLE DATA RATE: 8SPS to 860SPS
    • INTERNAL LOW-DRIFT VOLTAGE REFERENCE
    • INTERNAL OSCILLATOR
    • INTERNAL PGA
    • I2C INTERFACE: Pin-Selectable Addresses
    • FOUR SINGLE-ENDED OR TWO DIFFERENTIAL INPUTS
    • PROGRAMMABLE COMPARATOR
    • This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers
  • -20%

    AH175 Hall Sensor

    (0)
    Original price was: ₨300.00.Current price is: ₨239.00. Quick View

    Hall effect sensor is transducing devices used to detect and generate a voltage when in the presence of a magnetic field. They are designed to induce a voltage as an output when a magnetic field is present at its input. The output voltage can be variable depending on the magnitude of the magnetic field. Hall effect sensors, as they name states are effect sensors, which can be used to sense different categories, like speed, position of objects, rotational speed or frequency and be used as a fault detector. They can be used to detect a time-varying current, as time-varying current produce magnetic fields, which can then be sensed by the Hall effect transducer and produce a voltage with some proportion the amount of magnetic field present at the sensor.

  • -33%

    AMTECH RMA223 RMA-223 RMA559 Solder Paste Flux 10CC

    (0)
    Original price was: ₨299.00.Current price is: ₨199.00. Quick View
    • Flux Type: Original AMTECH RMA-223 UV (Made in USA)
    • Volume: 10ml/10cc
    • Dimension: 93 x 33 x 23mm
    • Material: the mixture of high-quality alloyed powder and resinic pasty flux, it can avoid the pale yellow residue.
    • Color: Colorless/Transparent
    • Insulated: Yes
    • With Needle Tip: Yes
    • Made in: USA
    • Application: for soldering and reballing of computer and phone chips.
    • Advantage: Good immersion and high-intensity joint.
    • Function: for PCB, BGA, and PGA reworking.
    • 100%: New Type, high quality.
  • -20%
    Out Of Stock

    ANALOG MULTIMETER YX-1000A

    (0)
    Original price was: ₨270.00.Current price is: ₨216.00. Quick View

    This analog multimeter has a capability of measuring DC voltages having four range setting, DC current having three range setting, AC voltages having four range setting and resistance having three range setting.

  • -14%
    Out Of Stock

    Analog Servo HD 1501mg

    (0)
    Original price was: ₨5,800.00.Current price is: ₨4,999.00. Quick View

    It is a metal geared analog servo which can deliver extra high torque as compared many high power servo motors

  • -26%
    Omron Analog Timer H3BA-8 24VDC Timer Relay
    Out Of Stock

    Analog Timer H3BA-8 24VDC Timer Relay

    (0)
    Original price was: ₨2,550.00.Current price is: ₨1,899.00. Quick View
  • -23%

    Analog Timer Relay H3BA-8 12V

    (0)
    Original price was: ₨1,550.00.Current price is: ₨1,199.00. Quick View
    • Model: H3BA-8
    • Brand: Omron
    • Output: DPDT
    • Usage/Application: INDUSTRIAL
    • Rated Current: 5A 12VAC
    • Mounting Type: Panel Mounting Timer
    • Display Type: Analog
    • Automation Grade: Semi-Automatic
  • -23%

    Analog Timer Relay H3BA-8 220V

    (0)
    Original price was: ₨1,500.00.Current price is: ₨1,149.00. Quick View
    • Model: H3BA-8
    • Brand: Omron
    • Output: DPDT
    • Usage/Application: INDUSTRIAL
    • Rated Current: 5A 220VAC
    • Mounting Type: Panel Mounting Timer
    • Display Type: Analog
    • Automation Grade: Semi-Automatic
  • -40%

    Analog/Digital LDR Module

    (0)
    Original price was: ₨250.00.Current price is: ₨149.00. Quick View
    • LDR module 4 PIN
    • Operating voltage 3.3V-5V
    • Signal output indicator light.
    • LDR module 4 PIN
    • Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)
  • -11%

    Android Cable (White)

    (0)
    Original price was: ₨200.00.Current price is: ₨179.00. Quick View
    • Charge your smartphone with this Micro USB cable
    • Enjoy smooth data transfers to/from computer, laptops
    • 1.5 Meter length cable
    • Lasts upto 10X longer than conventional cable.
    • Safe & Smart
    • Durable Product
  • Android charging cable for smart phones.

  • -27%
    Out Of Stock

    ANENG ST212 Digital DC/AC Clamp Meter Current 400A Amp Multimeter Large Color Screen

    (3)
    Original price was: ₨11,000.00.Current price is: ₨7,999.00. Quick View
    1. AC Current Range: 60A/400A
    2. DC Current Range: 60A/400A
    3. DC Voltage Range: 600V/600mV
    4. AC Voltage Range: 600V/600mV
    5. Resistance: 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ
    6. Capacitance: 60nF/600nF/6uF/60uF/600uF/6mF/60mF
    7. Temperature: -40~1000℃, -40~1832℉
    8. Frequency: 60Hz/1000Hz
    9. Colour: Red
    10. Material: ABS
    11. Display: LCD
    12. Max. Display Value: 6000 digit
    13. Sampling Time: About 3 times/second, bargraph 10 times/second
    14. Auto-off: 15 minutes
    15. Operating Temperature: 18~28℃
    16. Storage Temperature: -10~50℃
    17. Operating Height: Max. 2000m
    18. Power Supply: 2 * 1.5V AAA battery (NOT included)
    19. Item Size: 182 * 62.1 * 33.4mm / 7.17 * 2.44 * 1.31in
    20. Item Weight: 150g / 5.29oz
    21. Package Weight: 272g / 9.59oz
    22. Package Size: 21.7 * 8.5 * 4.5cm / 8.54 * 3.35 * 1.77in
  • -25%

    APDS9960 proximity and light intensity sensor I2C 3.3V

    (0)
    Original price was: ₨799.00.Current price is: ₨599.00. Quick View
    • Gesture recognition using reflected IR
    • Digital proximity sensing using reflected IR
    • Separate Red/Green/Blue light intensity sensors
    • Ambient (clear) light intensity sensor
    • IR light-blocking filter
    • Interrupt output available
    • I2C interface with good library support
    • 3.3V operation
  • -15%
    Out Of Stock

    APM Power Module

    (0)
    Original price was: ₨1,500.00.Current price is: ₨1,269.00. Quick View

    The power module has the ability to provide APM lossless power from a LiPo battery as well as current consumption and voltage measurements through 6-pos cable. The on board regulator switch has the ability of giving outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery.

  • Out Of Stock

    The ArduPilot Mega 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. This version is ready to use, with no assembly required. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints.

     

    This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it’s often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass, so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

  • -21%
    Out Of Stock

    APM2.8 ArduPilot Mega 2.8 Flight Control Board

    (0)
    Original price was: ₨19,000.00.Current price is: ₨15,000.00. Quick View

    This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.

    It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

  • -35%

    Arduino 28BYJ48 Stepper Motor with driver

    (0)
    Original price was: ₨850.00.Current price is: ₨549.00. Quick View

    Arduino 28BYJ48 Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug. Motor: Diameter: 28mmVoltage: 5VStep angle: 5.625 x 1/64Reduction ratio: 1/64ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31x35mmPackage included:1 x ULN2003 driver board1 x 28BYJ-48 stepper motor Options:

  • -7%
    Out Of Stock

    Arduino Cable Black 1.5m

    (0)
    Original price was: ₨70.00.Current price is: ₨65.00. Quick View
  • Out Of Stock
    • It is well designed to be durable during handling and repeated connections.
    • Cable transfer speed is up to 480Mbps.
    • USB Type: 2.0
    • Data transfer rate: up to 480Mbps
    • Connectors: USB type A tata-USB type B tata
    • Length: 1.3 m
    • Color: BLUE
  • -20%

    ARDUINO CNC SHIELD V3

    (0)
    Original price was: ₨500.00.Current price is: ₨399.00. Quick View
    1. Latest Arduino CNC Shield Version 3.10
    2. GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
    3. PWM Spindle and direction pins
    4. 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
    5. 2 x End stops for each axis (6 in total)
  • -28%
    Arduino Due AT91SAM3X8E ARM Cortex-M3 Board

    Arduino Due AT91SAM3X8E ARM Cortex-M3 Board

    (0)
    Original price was: ₨6,240.00.Current price is: ₨4,500.00. Quick View
    • MicrocontrollerAT91SAM3X8E
    • Operating Voltage3.3V
    • Input Voltage (recommended)7-12V
    • Input Voltage (limits)6-16V
    • Digital I/O Pins54 (of which 12 provide PWM output)
    • Analog Input Pins12
    • Analog Output Pins2 (DAC)
    • Total DC Output Current on all I/O lines130 mA
    • DC Current for 3.3V Pin800 mA
    • DC Current for 5V Pin800 mA
    • Flash Memory512 KB is all available for the user applications
    • SRAM96 KB (two banks: 64KB and 32KB)Clock Speed84 MHz
    • Length101.52 mm
    • Width53.3 mm
    • Weight36 g
  • Arduino jumper wire, Female to Female connector.

  • -42%

    Arduino Jumper Wire F/F 40Pcs

    (1)
    Original price was: ₨300.00.Current price is: ₨175.00. Quick View
    • 40 pieces of the 10cm female to female color Dupont jumper wires cables in one set will be sold together.
    • Color: as shown in the pictures.
    • Material: durable hard plastic and copper wire.
    • Each cable length: about 10cm /3.94 .
    • Connectors: 1pin-1pin female to female header.
    • 100% brand new and high quality 2.54mm Female to Female Color Dupont Jumper Wires Cables for Arduino Breadboard.
    • Compatible with 2.54mm spacing pin headers.
    • A popular choice for the construction or repair.
    • Can be used for electronic project and Genuine Arduino products.
    • Easy to install and use, durable and reusable to use.
  • Arduino jumper wire, male to male connector.

  • -40%

    Arduino Jumper Wire M/F 40Pcs

    (1)
    Original price was: ₨300.00.Current price is: ₨179.00. Quick View
    • Color: Multicolor.
    • Material: durable hard plastic andcopper wire.
    • Each cable length: about 10cm /3.94/.
    • Connectors: 1pin-1pin male to female header.
    • 100% brand new and high quality 2.54mm Male to Female Color Dupont Jumper Wires Cables for Arduino Breadboard.
    • Compatible with 2.54mm spacing pin headers.
    • A popular choice for the construction or repair.
    • Can be used for electronic project and Genuine Arduino products.
    • Easy to install and use, durable and reusable to use.
  • Arduino jumper wire, male to male connector.

  • -38%

    Arduino Jumper Wire M/M 40Pcs

    (1)
    Original price was: ₨300.00.Current price is: ₨185.00. Quick View
    • Compatible with 2.54 mm spacing pin headers.
    • 120 pcs chromatic color jump wire.
    • High quality and in good working condition.
    • Durable and reusable.
    • Easy to install and use.
    • A popular choice for construction or repair.
    • Be used for the electronic project and Genuine Arduino product.
    • Flexible Breadboard Jumper Cable Wire allows you to plug and unplug easily for prototyping.
  • -9%

    Arduino Leonardo R3

    (1)
    Original price was: ₨1,750.00.Current price is: ₨1,599.00. Quick View

    he Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

  • -24%

    Arduino MEGA 2560 PRO Mini

    (1)
    Original price was: ₨4,500.00.Current price is: ₨3,399.00. Quick View
    • Microcontroller ATmega2560
    • USB-TTL converter: CH340
    • Power Out:5V-800mA
    • Power IN.: 5V
    • Power IN. VIN/DC Jack:5V
    • Power Consumption: 5V 220mA
    • Logic Level: 5V
    • USB: Micro USB
    • Clock Frequency: 16MHz
    • Operating Supply Voltage: 5V
    • Digital I/O: 54
    • Analog I/O: 16
    • Memory Size: 256kb
    • Data RAM Type/Size: 8Kb
    • Data ROM Type/Size: 4Kb
    • Interface Type : ISP
    • Operating temperature 40C/+85C
    • Length x Width:38mmx54mm
  • -8%

    Arduino MEGA 2560 R3 ATMEGA16U2 Programing Board

    (2)
    Original price was: ₨4,000.00.Current price is: ₨3,699.00. Quick View
    • Arduino Mega 2560 rev3 ATmega2560 microcontroller
    • Input voltage – 7-12V
    • 54 Digital I/O Pins (14 PWM outputs)
    • 16 Analog Inputs
    • 256k Flash Memory
    • 16Mhz Clock Speed
  • -42%
    Arduino Mega 2560 R3 with ATmega16U2 microcontroller

    Arduino MEGA 2560 R3 ATMEGA16U2 Programing Board With Logo

    (5)
    Original price was: ₨6,000.00.Current price is: ₨3,499.00. Quick View
    • Arduino Mega 2560 rev3 ATmega2560 microcontroller
    • Input voltage – 7-12V
    • 54 Digital I/O Pins (14 PWM outputs)
    • 16 Analog Inputs
    • 256k Flash Memory
    • 16Mhz Clock Speed
  • -31%

    Arduino Nano USB Programming Cable

    (0)
    Original price was: ₨289.00.Current price is: ₨199.00. Quick View

    The Arduino Nano USB Cable connects your compatible Arduino Nano board to a computer for sketch uploading, programming, and serial data communication. Featuring a USB Type-A to Mini-B connection, it is a practical accessory for microcontroller development, robotics experiments, sensor testing, and DIY electronics projects. Its compact design helps keep your workbench and project setup organized.

  • -55%
    Arduino Nano V3 board ATmega328P in Pakistan – Electronation

    Arduino Nano V3

    (6)
    Original price was: ₨1,650.00.Current price is: ₨749.00. Quick View
    • Microcontroller: Atmel ATmega168 or ATmega328.
    • Operating Voltage (logic level): 5 V.
    • Input Voltage (recommended): 7-12 V.
    • Input Voltage (limits): 6-20 V.
    • Digital I/O Pins: 14 (of which 6 provide PWM output).
    • Analog Input Pins: 8.
    • DC Current per I/O Pin: 40 mA.
    • Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB is used by the boot loader.
    • SRAM : 1 KB (ATmega168) or 2 KB (ATmega328).
    • EEPROM : 512 bytes (ATmega168) or 1 KB (ATmega328).
    • Clock Speed: 16 MHz.
    • Dimensions : 0.73 x 1.70
    • Length: 45 mm.
  • -15%

    Arduino Porto PCB

    (0)
    Original price was: ₨350.00.Current price is: ₨299.00. Quick View

    The ProtoShield makes it easy for you to design custom circuits. You can easily solder TH or SMD ICs on the prototyping area to test them with your Arduino board. The SMD area is designed for a maximum of 24 pins SOIC integrated circuit and the TH area contains a lot of space for the needed components around your project. You can even stick a mini breadboard (not included) on the protoarea for solderless operation. The proto area includes also two power lines (IOREF and GND), two LEDs pads and SPI signals breakout pads for boards with SPI only on the ICSP header like Zero.

  • -30%
    Out Of Stock

    Arduino Pro Micro 5v 16m Atmega32u

    (0)
    Original price was: ₨2,000.00.Current price is: ₨1,399.00. Quick View
    • ATMEGA32U4 chip
    • Supply Voltage: 5VDC
    • Frequency: 16Mhz
    • Four 10 bit ADC pins
    • 12 pins Digital I/O
    • Dimension: 33mm x 18mm
  • -21%

    Arduino Pro Mini 5V 16Mhz ATMEGA328

    (0)
    Original price was: ₨1,399.00.Current price is: ₨1,099.00. Quick View
    1. 131 Powerful Instructions – Most Single Clock Cycle Execution
    2. Up to 20 MIPS Throughput at 20 MHz
    3. Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
    4. One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
    5. Real Time Counter with Separate Oscillator
    6. Six PWM Channels
    7. 8-channel 10-bit ADC in TQFP and QFN/MLF package
    8. Programmable Watchdog Timer with Separate On-chip Oscillator
    9. On-chip Analog Comparator
    10. 23 Programmable I/O Lines
  • -49%

    Arduino Proto Breadboard

    (0)
    Original price was: ₨679.00.Current price is: ₨349.00. Quick View
    • It has a nice standard 0.1×0.1 prototyping grid with big pads
    • Comes with Stacking headers and plain header, choose whichever you want when soldering together
    • A IC pattern for adding DIP ICs up to 20 pins
    • Power rails down the middle and sides
    • A reset button and an extra general use button
    • 2 3mm general use LEDs, red and green, as well as 2 matching resistors
    • A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
    • A surface-mount chip area for up to 14 SOIC size parts
    • Compatible with tiny breadboards
    • Every pin is brought out!
    • Gold plated pads
    • 2 x 0.1uF capacitors on either side for extra power stability
    • It has a nice standard 0.1×0.1 prototyping grid with big pads
  • -10%

    Arduino SD Card Reader Module

    (1)
    Original price was: ₨220.00.Current price is: ₨199.00. Quick View
    • Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
    • The level conversion circuit board that can interface level is 5V or 3.3V\
    • Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
    • Communication interface is a standard SPI interface
    • 4 M2 screw positioning holes for easy installation
    • Size: 4.1 x 2.4cm
  • -15%

    Arduino Sensor Shield

    (0)
    Original price was: ₨350.00.Current price is: ₨299.00. Quick View
    • It has a Pin 13 LED pilot.
    • It has D0-D13 IO ports.
    • A0-A5 analog IO ports.
    • It contains a reset button.
    • It also contains a Power LED.
    • It has an SD card interface.
    • It contains an Ultrasonic interface.
    • This expansion board has an RS232 interface.
    • It has a Bluetooth interface.
    • It has an APC220 interface.
    • IIC interface.
    • 12864 LCD Parallel interfaces.
    • It contains 12864 LCD Serial Interface
  • -18%

    Arduino Starter Kit RFID Based

    (1)
    Original price was: ₨8,500.00.Current price is: ₨6,999.00. Quick View

    Arduino Starter Kit RFID Based walks you through the basics of using the Arduino & RFID in a hands-on way. You’ll learn through building several creative projects. The kit includes a selection of the most common and useful electronic components with a book of 15 projects. Starting from the basics of electronics to more complex projects, the kit will help you control the physical world with sensors and actuators.

    This kit aims to bring Arduino together with RFID technology, which will support individual production. With this kit, you will be able to use RFID with the code you wrote in Arduino. You will be able to come up with a practical technology such as Arduino, a technology that many people like RFID are trying to get into and stay away from using. All of the components and components required for RFID technology are combined in this kit.

    Radio Frequency Identification (RFID) is the given name to the technology used to identify objects using radio waves. An RFID microchip embedded in a tag, keychain or card communicates with the reader/writer module to transfer data.

  • -60%
    Arduino UNO R3 Dip

    Arduino UNO R3 Dip

    (4)
    Original price was: ₨3,500.00.Current price is: ₨1,399.00. Quick View
    • ATmega328 microcontroller
    • Input voltage – 7-12V
    • 14 Digital I/O Pins (6 PWM outputs)
    • 6 Analog Inputs
    • 32k Flash Memory
    • 16Mhz Clock Speed
    • ATmega328
    • Operating Voltage 5V
    • Input Voltage (recommended) 7-12V
    • Input Voltage (limits) 6-20V
    • Digital I/O Pins 14 (of which 6 provide PWM output)
    • Analog Input Pins 6
    • DC Current per I/O Pin 40 mA
    • DC Current for 3.3V Pin 150 mA
    • Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM
    • 2 KB (ATmega328) EEPROM
    • 1 KB (ATmega328)
    • Clock Speed 16 MHz
  • -47%

    Arduino UNO R3 Dip WITH CABLE

    (2)
    Original price was: ₨3,000.00.Current price is: ₨1,579.00. Quick View
    • ATmega328 microcontroller
    • Input voltage – 7-12V
    • 14 Digital I/O Pins (6 PWM outputs)
    • 6 Analog Inputs
    • 32k Flash Memory
    • 16Mhz Clock Speed
    • ATmega328
    • Operating Voltage 5V
    • Input Voltage (recommended) 7-12V
    • Input Voltage (limits) 6-20V
    • Digital I/O Pins 14 (of which 6 provide PWM output)
    • Analog Input Pins 6
    • DC Current per I/O Pin 40 mA
    • DC Current for 3.3V Pin 150 mA
    • Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM
    • 2 KB (ATmega328) EEPROM
    • 1 KB (ATmega328)
    • Clock Speed 16 MHz