Shop

Default sorting
Show
48
  • -46%
    Out Of Stock

    IR Obstacle Avoidance Sensor

    IR & Vision
    (0)
    Original price was: ₨250.00.Current price is: ₨135.00. Quick View
    • There is an obstacle, the green indicator light on the circuit board
    • Detection distance: 2 ~ 30cm
    • Detection angle: 35
    • Comparator chip: LM393
    • 3mm screw holes for easy mounting
  • -17%

    Flex Sensor 2.2 Inch

    Flex & Force
    (0)
    Original price was: ₨3,600.00.Current price is: ₨2,999.00. Quick View
    • Angle Displacement Measurement
    • Bends and Flexes physically with motion device
    • Possible Uses
    • Simple Construction
    • Low Profile
    • Physical Therapy
    • Musical Instruments
    • Computer Peripherals
    • Medical Devices
    • Gaming (Virtual Motion)
    • Robotics
  • -15%

    Force Sensitive Resistor 0.5 INCH FSR

    Flex & Force
    (0)
    Original price was: ₨1,350.00.Current price is: ₨1,150.00. Quick View
    • Detection area (detection range): 14.5 mm circle
    • Physical Diameter: 18.3mm circle
    • The output signal (output signal): Passive variable to hold
    • The Force-sensitive range (range), pressure test: 100g to 10 kg
    • Lifespan (life):> 10 m letter actuation

    Dimensions:

    • Total length: 56mm
    • Overall width: 18.3mm
    • Diameter detection: 14.5mm
    • Thickness: 0.4mm
  • -28%

    MQ135 Air Quality Detector Sensor Module

    Gas Sensor
    (0)
    Original price was: ₨540.00.Current price is: ₨389.00. Quick View
    1. Air Quality Sensor Module
    2. Condition: New
    3. Size: 32mm X22mm X27mm
    4. Main chip: MQ-135
    5. Operating Voltage: 5V DC
    6. Type: Analog & Digital
    7. Sensitivity to Ammonia, Sulphide and Benzene steam
    8. Detecting Range: 100-1000ppm
    9. With signal output instructions
    10. TTL output signal is low level
    11. Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
    12. Color is showing pictures.
    13. Sensitive for benzene, alcohol, smoke
    14. Fast response and recovery
    15. Adjustable sensitivity
    16. Signal output indicator
    17. Output voltage boosts along with the concentration of the measured gases increases
  • -17%

    MQ2 MQ-2 SMOKE SENSOR MODULE

    Gas Sensor
    (1)
    Original price was: ₨350.00.Current price is: ₨289.00. Quick View
    • Operating voltage: 5V
    • Analog output voltage: 0V to 5V
    • Digital output voltage: 0V or 5V (TTL Logic)
    • Preheat duration: 20 seconds
    • Sensitivity range: 200 to 10,000 ppm
    • Gases detected: LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide
    • Dimensions: 3.6 x 2 x 1 cms
    • Weight: 5 grams
  • -27%

    GY521 MPU6050 Module 6DOF

    Accelero, Gyro. IMU, Magneto
    (1)
    Original price was: ₨550.00.Current price is: ₨399.00. Quick View
    • Chip: MPU-6050
    • Power supply: 3v-5V
    • Gyroscope range: + 250 500 1000 2000/ s
    • Acceleration range:  2  4  8  16 g
    • Communication: Standard IIC communication agreement
    • Chip built-in 16 bit AD converter, 16 bits of data output
    • Pin Pitch 2.54 mm
    • SIZE: 20.3mm x 15.6mm
  • -41%

    GY-291 ADXL345 3-Axis Accelerometer Module

    Accelero, Gyro. IMU, Magneto
    (0)
    Original price was: ₨590.00.Current price is: ₨349.00. Quick View
    • Main Chip: ADXL345
    • Model: GY-291
    • Power Supply: 3-5V
    • Means of Communication: IIC / SPI Communication Protocol
    • Measuring Range: ±2g /±16g
    • Digital-Output Triple-Axis Accelerometer with a Programmable Full-Scale Range of ±2g, ±4g, ±8g and ±16g and Integrated 16-bit ADCs
    • Accelerometer Normal Operating Current: 450µA
    • Ultralow Power: as low as 23 μA in Measurement Mode and 0.1 μA in Standby Mode at VS = 2.5 V (typical)
    • Sleep Mode Current: 8µA
    • Communication: SPI (3- and 4-wire) and I2C Digital Interfaces
    • User-Programmable Interrupts
    • Wake-On-Motion Interrupt for Low Power Operation of Applications Processor
  • -12%

    Gy-61 Triple Axis Accelerometer Adxl335

    Accelero, Gyro. IMU, Magneto
    (1)
    Original price was: ₨1,990.00.Current price is: ₨1,749.00. Quick View
    1. 3V-6V DC Supply Voltage
    2. Onboard LDO Voltage regulator
    3. Can be interfaced with a 3V3 or 5V Microcontroller.
    4. All necessary components are populated.
    5. Ultra Low Power: 40uA in measurement mode, 0.1uA in standby@ 2.5V
    6. Tap/Double Tap Detection
    7. Free-Fall Detection
    8. Analog output
    9. Build in ultra-low noise linear LDO voltage regulator
    10. Built-in onboard filters, which reduce noise from the motor and other high-current electronics
    11. All sensors connected to the I2C bus
    12. You can easily select two I2C addresses for MPU6050 by soldered jumper
    13. Power LED
    14. Build in Logic level converter for I2C
    15. Dimensions 20x16mm
    16. Designed for 5V logic level
  • -20%

    GY-273 Magneto HMC5883L

    Accelero, Gyro. IMU, Magneto
    (0)
    Original price was: ₨750.00.Current price is: ₨599.00. Quick View
    1. Supply Voltage VCC: 3.3 to 6 V
    2. Heading Accuracy: 1 to 2
    3. Magnetic Field Range: -8 to +8 Gauss
    4. I2C Address: 0x1E (7-bit address)
    5. Max Data Rate: 160 Hz
    6. Digital Voltage Level: 3.3V
    7. Dimensions (excluding pins): 18.2mm (0.717) x 13.3mm (0.524) x 2.2mm (0.087)
    8. Weight: 0.95g (0.034oz)
  • -10%
    Out Of Stock

    GPS Arduino Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨5,350.00.Current price is: ₨4,799.00. Quick View

    This is a GPS module breakout board with SD storage based on the u-blox NEO-6M GPS and its foot print is compatible with arduino boards . This board features an SD card socket, which makes it convenient for building data loggers.

  • -14%

    W5100 Ethernet Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨3,500.00.Current price is: ₨2,999.00. Quick View
    • Operating voltage 5V (supplied from the Arduino Board)
    • Ethernet Controller: W5100 with internal 16K buffer
    • Connection speed: 10/100Mb
    • Connection with Arduino on SPI port
    • The Shield contains a number of informational LEDs
    • PWR: indicates that the board and shield are powered
    • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
    • FULLD: indicates that the network connection is full duplex
    • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
    • RX: flashes when the shield receives data
    • TX: flashes when the shield sends data
    • TX: flashes when the shield sends data
    • COLL: flashes when network collisions are detected
  • Out Of Stock

    Arduino WiFi Shield CC3000

    Arduino & IOT Boards
    (0)
    ₨2,800.00 Quick View
    1. Based on TI CC3000 WIFI module.
    2. Use SPI communication .
    3. Integrated 3.3V regulator .
    4. Level shifter integrated .
    5. Integrated ceramic antenna .
    6. It has a connector for external antenna WIFI
    7. Compatible with Arduino UNO, Mega, Leondardo & Micro
    8. Antenna: Onboard Ceramic
    9. MicroSD card slot onboard
    10. Reset button
    11. Communication Protocol: SPI
    12. Connects via IEEE 802.11 b/g networks
    13. Tx Bandwidth: 11Mbps
    14. Tx Sensitivity: +/-18dBm
    15. Rx sensitivity: -86dBm
    16. IRQ pin for interrupts (useful for asynchronous connections)
    17. Supports WEP, WPA, WPA2, TKIP and AES
    18. TCP and UDP Client & Server Modes available
    19. Max Concurrent TCP/UDP Sockets: 4
    20. TCP/IP stack is built in.
  • Hot
    -55%
    Arduino Nano V3 board ATmega328P in Pakistan – Electronation

    Arduino Nano V3

    Arduino & IOT Boards
    (5)
    Original price was: ₨1,650.00.Current price is: ₨749.00. Quick View
    • Microcontroller: Atmel ATmega168 or ATmega328.
    • Operating Voltage (logic level): 5 V.
    • Input Voltage (recommended): 7-12 V.
    • Input Voltage (limits): 6-20 V.
    • Digital I/O Pins: 14 (of which 6 provide PWM output).
    • Analog Input Pins: 8.
    • DC Current per I/O Pin: 40 mA.
    • Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB is used by the boot loader.
    • SRAM : 1 KB (ATmega168) or 2 KB (ATmega328).
    • EEPROM : 512 bytes (ATmega168) or 1 KB (ATmega328).
    • Clock Speed: 16 MHz.
    • Dimensions : 0.73 x 1.70
    • Length: 45 mm.
  • -9%

    Arduino Leonardo R3

    Arduino & IOT Boards
    (1)
    Original price was: ₨1,750.00.Current price is: ₨1,599.00. Quick View

    he Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

  • Hot
    -33%

    Arduino UNO R3 SMD – Economic WITH CABLE

    Arduino & IOT Boards
    (3)
    Original price was: ₨1,500.00.Current price is: ₨999.00. Quick View
    1. ATmega328-AU microcontroller with UNO Bootloader Installed.
    2. USB Programming Facilitated by the CH340G.
    3. USB-B Connector and cable included.
    4. Input voltage – 7-15V.
    5. 0-5V outputs with 3.3V compatible inputs.
    6. 14 Digital I/O Pins (6 PWM outputs).
    7. 6 Analog Inputs.
    8. ISP Header.
    9. 32k Flash Memory.
    10. 16MHz Clock Speed.
    11. All SMD Construction.
    12. R3 Shield Compatible
  • Hot
    -47%

    Arduino UNO R3 Dip WITH CABLE

    Arduino & IOT Boards
    (2)
    Original price was: ₨3,000.00.Current price is: ₨1,579.00. Quick View
    • ATmega328 microcontroller
    • Input voltage – 7-12V
    • 14 Digital I/O Pins (6 PWM outputs)
    • 6 Analog Inputs
    • 32k Flash Memory
    • 16Mhz Clock Speed
    • ATmega328
    • Operating Voltage 5V
    • Input Voltage (recommended) 7-12V
    • Input Voltage (limits) 6-20V
    • Digital I/O Pins 14 (of which 6 provide PWM output)
    • Analog Input Pins 6
    • DC Current per I/O Pin 40 mA
    • DC Current for 3.3V Pin 150 mA
    • Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM
    • 2 KB (ATmega328) EEPROM
    • 1 KB (ATmega328)
    • Clock Speed 16 MHz