• XBee 2mW Wire Antenna – Series 2 (ZB)

    Original price was: ₨5,600.00.Current price is: ₨4,999.00.

    This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.

  • XBee 2mW PCB Antenna – Series 2 (ZigBee Mesh)

    Original price was: ₨6,000.00.Current price is: ₨4,999.00.

    This is the XBee XB24-Z7CIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
    These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
    This Xbee also has a chip antenna which is basically a small chip that acts as an antenna. Quick, easy, cheap, and not in the way.

  • Voice Recognition Module

    Original price was: ₨5,600.00.Current price is: ₨4,799.00.
    • Voltage: 4.5-5.5V
    • Current: <40mA
    • Digital Interface: 5V TTL level for UART interface and GPIO
    • Analog Interface: 3.5mm mono-channel microphone connector
      and microphone pin interface
    • Size: 31mm x 50mm
    • Recognition accuracy: 99% (under ideal environment)
  • GPS Arduino Shield

    Original price was: ₨5,350.00.Current price is: ₨4,799.00.

    This is a GPS module breakout board with SD storage based on the u-blox NEO-6M GPS and its foot print is compatible with arduino boards . This board features an SD card socket, which makes it convenient for building data loggers.

  • XBee 1mW Wire Antenna

    Original price was: ₨6,500.00.Current price is: ₨4,549.00.

    INTRODUCTION

    This is the very popular 2.4GHz XBee module from Digi (formally Maxstream). These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
    Pair a couple of these XBees with a Regulated Explorer, and a USB Explorer and you’ve got a great gift for that special electronics geek!
  • Arduino Due AT91SAM3X8E ARM Cortex-M3 Board

    Original price was: ₨6,000.00.Current price is: ₨4,500.00.
    • MicrocontrollerAT91SAM3X8E
    • Operating Voltage3.3V
    • Input Voltage (recommended)7-12V
    • Input Voltage (limits)6-16V
    • Digital I/O Pins54 (of which 12 provide PWM output)
    • Analog Input Pins12
    • Analog Output Pins2 (DAC)
    • Total DC Output Current on all I/O lines130 mA
    • DC Current for 3.3V Pin800 mA
    • DC Current for 5V Pin800 mA
    • Flash Memory512 KB is all available for the user applications
    • SRAM96 KB (two banks: 64KB and 32KB)Clock Speed84 MHz
    • Length101.52 mm
    • Width53.3 mm
    • Weight36 g
  • 6Legs Robotic Kit

    4,500.00

    This Robot is made of 18 SG90 Servo Motors
    To make this robot move, we just need the control software and the following components:
    1.6 Legs 18 DOF Robot Black Spider Robot 18pcs SG90 Servo Motor
    2.32 Channels Servo Motor Controller Robot Contorller Servo Driver
    3.7.4V power supply

  • DPS-750DB-1 A 10Amp Switching Power Supply Refurbished

    Original price was: ₨4,999.00.Current price is: ₨4,444.00.
    • Model:?DPS-750DB-1 A
    • Amperes: 10.0A
    • Input: 47-63hz 100-240V and 10A
    • Output: 750W max

    +12v / 62A max

    +5VSB /2.0A max

  • XM18 Incubator Controller Thermostat Full Automatic

    Original price was: ₨7,000.00.Current price is: ₨4,299.00.

    XM18 Automatic Thermostat Incubator Egg Incubator Controller Multifunctional Automatic Incubator Industrial Incubators Temperature Probe for Breeding Chicken Duck Adopt the latest microelectronics technology and new components strong anti-interference ability, high work stability and high precisionHumanized four-screen display design, convenient to use Adopt the latest microelectronics technology and new components strong anti-interference ability, high work stability and high precisionHumanized four-screen display design, convenient to use XM18 Automatic Thermostat Incubator Micro-electronic technology and new electric parts. Digital displaying of temperature, humidity, and turning frequency

  • 1500W 30A CONVERTER STEP UP POWER SUPPLY MODULE

    Original price was: ₨4,999.00.Current price is: ₨4,299.00.

    When using the boost power supply should pay attention to the following points:

    1. the output polarity cannot be reversed or short circuit.

    2. when using batteries as the input source, you must lower the battery protection, otherwise it will damage the battery and power supply

    3. Input power supply voltage must be above 10V.

    4. When the power supply is used for the input power supply, the input power and the output voltage of the input power supply are the first to be unloaded. Then pick up the load. (must ensure that the switching power supply has been working).

    5. When the constant current mode is used to set the voltage, the constant voltage must be higher than the input voltage.Do not use the way of short circuit output current,the circuit structure of the boost module can not be adjusted in short circuit way.

    6. If the input voltage fluctuation range is lower than the set output voltage,then the output voltage is constant, it is to ensure that input is lower than the output voltage.

  • Uni-T UT201+ True RMS Digital Clamp Multimeter

    Original price was: ₨5,000.00.Current price is: ₨3,999.00.

    UNI T UNI-T Digital Clamp Meter UT201+ AC DC Current Amperimetro Tester Clamp Multimeter Resistance Frequency Tester

    UT201+

    UT201+ 600V AC DC Voltage Measurement, 400A AC Current Measure, MAX/MIN/true RMS Function:AC/DC voltage, AC Current Measure,Diode Test,Resistance ,Continutity Buzzer,AC Frenquency, Backlight

     

  • Raspberry PI Camera with IR

    Original price was: ₨4,500.00.Current price is: ₨3,999.00.

    The Raspberry Pi IR-CUT Camera is a day and night camera. You can get the best imaging whatever it is in the daytime or at night. It’s a built-in IR-CUT camera, can be used during the day and night, When the camera in the daytime will switch to day mode, the camera image is a normal color image, When the camera at night will switch to night mode, the camera can normally identify the infrared fill light Of the light, which can be set through the software switch, to solve the other night vision version camera during the day to take pictures of the image color is not normal.

  • 3s 1500mA

    Original price was: ₨4,500.00.Current price is: ₨3,999.00.

    1500mAh rating high discharge LiPo battery

  • Xbee shield V03

    Original price was: ₨5,000.00.Current price is: ₨3,999.00.
    This shield V03 can achieve a simple two crunodal ZigBee network, achieve wireless communication between Ardu, and allows the Ardu to wireless communicate over a modified ZigBee protocol using the popular XBee module.
    It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.
  • 3.5″ IPS TFT LCD for Arduino MEGA2560

    Original price was: ₨5,000.00.Current price is: ₨3,899.00.
    • Screen size 3.5″ – 480 X 320 Pixels
    • Support Arduino Mega2560 directly
    • Control IC: ILI9846
    • Compatible with 3.3/5V operation voltage level
    • Full-angle IPS TFT panel
    • With SD card Socket
    • Interface: 16 Bit parallel interface
  • Telemetry 3DR TTL

    3,800.00

    The Radio telemetry system base on 3DR Radio system and 100% compatible.

    It’s designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. Its available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).

    The system provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.

    Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.

  • LiPo 11.1v 3300mAH 35C – HRB

    3,700.00

    3S 11.1V 3300mah 35C?Lipo Battery with hardcase?For 1/10th RC Car Boat ?.

  • -8%
    Quick View

    Arduino MEGA 2560 R3 ATMEGA16U2 Programing Board

    Original price was: ₨4,000.00.Current price is: ₨3,699.00.
    • Arduino Mega 2560 rev3 ATmega2560 microcontroller
    • Input voltage – 7-12V
    • 54 Digital I/O Pins (14 PWM outputs)
    • 16 Analog Inputs
    • 256k Flash Memory
    • 16Mhz Clock Speed
  • QQ Thunder Flight Controller

    3,600.00

    The QQ Super Multi-rotor flight control is built-in precise digital gyroscope and acceleration sensor with self-stabilizing function and super stable flight performance. Besides all standard PCM and 2.4G digital receiver, It also compatiblr with S.BUS DSM2 and DSMX satellite. And it’s also easy in connection and installation with ultra-bright LED light

  • Teensy 3.1

    3,600.00

    The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. The Teensy 3.1 brings a 32 bit ARM Cortex microprocessor into the mix so you can do some serious number crunching.

    The Teensy 3.1 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! You can program for the Teensy in your favorite program editor using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!

    The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32 bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access, several high-resolution ADCs and even an I2S digital audio interface! There are also 4 separate interval timers plus a delay timer! Oh yeah, and all pins have interrupt capability. Also, it can provide system voltage of 3.3V to other devices at up to 100mA.

  • EdCreate Edison robot creator’s kit

    Original price was: ₨4,410.00.Current price is: ₨3,528.00.

    EdCreate is the Edison robot creator’s kit, a 5-in-1 expansion pack construction system to create, invent and build interactive, programmable projects.

  • LiPo 11.1v 3000mAH 25C – BlackMagic

    3,500.00

    Features:

    For DJI PHANTOM Quadcopter, in no-load and load conditions can be effectively enhanced blank time
    Suitable for CX-20, Quanum Nova Quadcopter
    Special for DJI PHANTOM 1 and FC40 Quadcopter,improve about 30% flight time than original battery
    Well-designed,have a special handle for take out the battery easily

  • LiPo 11.1v 3500mAH 25C TCB

    3,500.00

    Capable of maximum continuous discharge rates up to 25C, placing this battery among the most powerful Li-Po battery packs in its class! It offer an excellent blend of weight, power and performance.

  • R307 Finger Print Sensor (R-307)

    Original price was: ₨4,000.00.Current price is: ₨3,499.00.
    1. Supply voltage: DC 4.2 ~ 6.0V
    2. Working current: 50mA (typical)
    3. Peak current: 80mA
    4. Fingerprint image input time: <0.3 seconds
    5. Window area: 14×18 mm
    6. Comparison method: (1: 1)
    7. Search method: (1: N)
    8. Characteristic file: 256 bytes
    9. Template file: 512 bytes
    10. Storage capacity: 1000 pieces
    11. Security Level: Five (from low to high: 1,2,3,4,5)
    12. Fake rate (FAR): <0.001%
    13. Refusal rate (FRR): <1.0%
    14. Search time: <1.0 seconds (1: 1000 hours, mean value)
    15. Host interface: UART, USB1.1
    16. Communication baud rate (UART): (9600xN) bps Where N = 1 ~ 12 (default N = 6, ie 57600bps)
    17. Working environment: Temperature: -20 ℃ – +40 ℃
    18. Relative humidity: 40% RH-85% RH (no condensation)
    19. Overall Size: 4.5×2.4x2cm
  • UNI-T UT33A+ Palm Size Multimeter

    Original price was: ₨4,250.00.Current price is: ₨3,499.00.

    Specification

    • Brand Name:UNI-T
    • Model Number:UT33A
    • DIY Supplies:Electrical
    • Measuring Current Range:400mA/4mA/40mA/400mA/10A
    • Operating Temperature:0 – 50
    • Measuring Voltage Range:400mV/4V/40V/400V/500V
    • Display Type:Digital Display
    • Dimensions:13 x 7.5 x 2.5cm
    • Measuring Capacitance Range:–
    • Measuring Resistance Range:400/4k/40k/400k/4M/40MOhm
  • Pressure Sensor MPX5700AP

    Original price was: ₨4,000.00.Current price is: ₨3,499.00.
    1. On-chip signal conditioned, temperature compensated and calibrated
    2. 2.5% maximum error over 0°C to 85°C
    3. Ideally suited for microprocessor or microcontroller-based systems
    4. Patented silicon shear stress-strain gauge
    5. Pressure ranges from 15KPa to 700KPa
    6. Supply voltage ranges from 4.75VDC to 5.25VDC
    7. Sensitivity of 6.4mV/KPa
    8. Response time of 1ms
    9. Durable epoxy unibody element
    10. Operating temperature ranges from -40°C to 125°C
  • Flex Sensor 4.5″

    Original price was: ₨4,000.00.Current price is: ₨3,499.00.
    • Thickness: 0.4mm
    • Trigger Force: 20g, triggered (default resistance<200kΩ)
    • Pressure Measuring Range: 20g~6kg
    • Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz)
    • Initial Resistance: >10MΩ
    • Activation Time: <0.01S
    • Operating Temperature: -40℃~+85℃
    • Lifespan: >1million times
    • Hysteresis: +10%,(RF+ -RF-)/FR+,1000g Force
    • Response Time: <10ms
    • Drift: <5%, 2.5Kg Force, Static load 24H
  • LiPo 11.1v 2700mAH 25C – BlackMagic

    3,300.00

    Features:

    Black Magic 2700mAh 11.1V 25C LiPo Battery for DJI PHANTOM Quadcopter, in no-load and load conditions can be effectively enhanced blank time, enjoy more flight fun!

  • 12V Spot Welder Set Portable Battery Spot Welding Storage Machine

    Original price was: ₨4,500.00.Current price is: ₨3,299.00.
    • Material: PCB
    • Suitable for: 18650/26650/32650 lipo battery
    • System voltage: 12-V-14.6V
    • Working current: 90-150A
    • Suggested battery: (not included)
    • 20-45ah Lead-acid battery with fine performance and small internal resistance
    • 3.5-5.5ah 45C 3S aeromodel lithium battery pack
    • 30-35ah capacity 18650 battery pack
    • Package size: 190 * 110 * 30mm / 7.5 * 4.3 * 1.2in
    • Package weight: 110g / 3.9ounce
  • 12V 7AMP Lead Acid Battery

    Original price was: ₨3,600.00.Current price is: ₨3,099.00.
    • Toy Battery Cars and Bikes are the most popular applications.
    • Battery Type – 12V 7 Amp lead-acid battery
    • Usage – Home, bike and toy car
    • Capacity (Ah) – 7000 Ah
  • Mecanum Wheel

    Original price was: ₨4,200.00.Current price is: ₨3,000.00.

    Also known as omni wheels or ilon wheels. It consist of a hub of rollers oriented 45 degree to the axis of rotation. It can move forward, backwards, side to side and even rotate.

  • Metal DC Geared Motor w/Encoder – 12V 251RPM 18Kg.cm

    3,000.00
    This is a Gear Motor w/Encoder, model No.GB37Y3530-12V-251R. It is a powerful 12V motor with a 43.8:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 16 counts per revolution of the motor shaft, which corresponds to 700 counts per revolution of the gearboxs output shaft.
    These units have a 0.61″ long, 6 mm(0.24″)-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V.
    The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm(0.61″) apart.
    This motor is an ideal option for your mobile robot project.
    Warning: Do not screw too far into the mounting holes as the screws can hit the gears. Manufacturer recommends screwing no further than 3mm (1/8″) into the screw hole.
  • 12V DC Motor 350RPM w/Encoder (12kg*cm)

    3,000.00

    This is a gear motor with encoder. It is a motor with a 34:1 gearbox and an integrated quadrature encoder that provides a resolution of 11 pulse single per round giving a maximum output of 374 within one round. With an Arduino controller and motor driver, applications for this include a closed-loop PID control or PWM motor speed control. This motor is an ideal option for mobile robot projects. The copper output shaft, embedded thread and reinforced connector greatly extends the motor’s service life.

  • -33%
    Quick View

    Arduino MEGA 2560 PRO Mini

    Original price was: ₨4,500.00.Current price is: ₨2,999.00.
    • Microcontroller ATmega2560
    • USB-TTL converter: CH340
    • Power Out:5V-800mA
    • Power IN.: 5V
    • Power IN. VIN/DC Jack:5V
    • Power Consumption: 5V 220mA
    • Logic Level: 5V
    • USB: Micro USB
    • Clock Frequency: 16MHz
    • Operating Supply Voltage: 5V
    • Digital I/O: 54
    • Analog I/O: 16
    • Memory Size: 256kb
    • Data RAM Type/Size: 8Kb
    • Data ROM Type/Size: 4Kb
    • Interface Type : ISP
    • Operating temperature 40C/+85C
    • Length x Width:38mmx54mm
  • INFRARED TEMPERATURE SENSOR GY-906 MLX90614

    Original price was: ₨3,950.00.Current price is: ₨2,999.00.
    • Easy to integrate
    • Mounted on a breakout board with two types of pins
    • 10k Pull up resistors for the I2C interface with optional solder jumpers
    • Factory calibrated in temperature range:
      • -40+125C for sensor temperature
      • -70+380C for object temperature
    • High accuracy of 0.5C over a wide temperature range (+50C for both) High (medical) accuracy calibration
    • The measurement resolution of 0.02C
    • Single and dual-zone versions
    • SMB is compatible digital interface
    • Customizable PWM output for continuous reading
    • Different package options for applications and measurements versatility
  • Meanwell Switching Power Supply 24V-5A

    Original price was: ₨3,799.00.Current price is: ₨2,999.00.
    • DC-output: 24V, DC, adjustable via potentiometer, range 20V – 28V
    • DC-current continuous max.: 5A
    • Max. power : 120W
    • Required min-load: 0A
    • Ripple max.: 150mVpp
    • Efficiency: typical 87%
    • Working temperature: -20 to +70°C
    • AC-input range: 88 – 264V AC or 124 – 370V DC
    • Connector: screw-terminal, M4
    • Weight: 0.5kg measure
    • Dimensions LxWxH: mm
  • UT33C+ Palm Size Multimeter

    Original price was: ₨3,600.00.Current price is: ₨2,999.00.

    The new generation UT33+ series redefines the performance standards for introductory digital multimeters. Our innovative industrial design makes sure that these products can withstand 2 meters drop. The new LCD display layout provides a better user experience. The UT33+ series safety standards have also been enhanced to ensure that users can work safely in CAT ll 600V environment.

  • Quadcopter Frame – F450 V3

    Original price was: ₨4,000.00.Current price is: ₨2,999.00.

    Quadcopter / Multi copter Quad-x frame kit in un-assembled form.

  • Flex Sensor 2.2 Inch

    Original price was: ₨3,600.00.Current price is: ₨2,999.00.
    • Angle Displacement Measurement
    • Bends and Flexes physically with motion device
    • Possible Uses
    • Simple Construction
    • Low Profile
    • Physical Therapy
    • Musical Instruments
    • Computer Peripherals
    • Medical Devices
    • Gaming (Virtual Motion)
    • Robotics
  • W5100 Ethernet Shield

    Original price was: ₨3,500.00.Current price is: ₨2,999.00.
    • Operating voltage 5V (supplied from the Arduino Board)
    • Ethernet Controller: W5100 with internal 16K buffer
    • Connection speed: 10/100Mb
    • Connection with Arduino on SPI port
    • The Shield contains a number of informational LEDs
    • PWR: indicates that the board and shield are powered
    • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
    • FULLD: indicates that the network connection is full duplex
    • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
    • RX: flashes when the shield receives data
    • TX: flashes when the shield sends data
    • TX: flashes when the shield sends data
    • COLL: flashes when network collisions are detected
  • Raspberry Pi TFT 3.5″

    Original price was: ₨3,599.00.Current price is: ₨2,879.00.

    This is a portable 3.5″ resistance touchscreen designed for Raspberry Pi b+, Raspberry Pi 2 and Raspberry Pi 3. All the Raspberry Pi GPIO are accessible through pin headers at the side of the screen.

  • R305 fingerprint sensor

    Original price was: ₨2,930.00.Current price is: ₨2,850.00.
    1. Peak Current: 150mA
    2. Matching Mode:  1:1 and 1:N
    3. Baud rate (9600*N)bps, N=1-12 (default N=6 57600bps)
    4. Character file size:  256 bytes
    5. Image acquiring time:  <0.5s
    6. Template size:  512 bytes
    7. Storage capacity:  120
    8. Security level: 5 (1, 2, 3, 4, 5(highest))
    9. FAR: <0.001%
    10. FRR: <0.1%
    11. Average searching time:  < 0.8s (1:880)
    12. Storage environment Temp: -40℃- +85℃
    13. RH: 40%-85% RH: <85%
  • STM32L152C-DISCO, STM32L Discovery Kit

    2,800.00

    32L152CDISCOVERY, Discovery kit for STM32L151/152 line – with STM32L152RC MCU

  • Arduino WiFi Shield CC3000

    2,800.00
    1. Based on TI CC3000 WIFI module.
    2. Use SPI communication .
    3. Integrated 3.3V regulator .
    4. Level shifter integrated .
    5. Integrated ceramic antenna .
    6. It has a connector for external antenna WIFI
    7. Compatible with Arduino UNO, Mega, Leondardo & Micro
    8. Antenna: Onboard Ceramic
    9. MicroSD card slot onboard
    10. Reset button
    11. Communication Protocol: SPI
    12. Connects via IEEE 802.11 b/g networks
    13. Tx Bandwidth: 11Mbps
    14. Tx Sensitivity: +/-18dBm
    15. Rx sensitivity: -86dBm
    16. IRQ pin for interrupts (useful for asynchronous connections)
    17. Supports WEP, WPA, WPA2, TKIP and AES
    18. TCP and UDP Client & Server Modes available
    19. Max Concurrent TCP/UDP Sockets: 4
    20. TCP/IP stack is built in.
  • So-Tech Surge Protector Socket 2200W ST-103U

    Original price was: ₨4,000.00.Current price is: ₨2,799.00.
  • -13%
    Quick View

    High Quality 37 in 1 Sensor Module Board Set Kit For Arduino

    Original price was: ₨3,200.00.Current price is: ₨2,799.00.

    This 37 in 1 Sensor Module Kit for Arduino is supplied with a variety of sensors that are compatible with Arduino Boards. This is the most complete performance starter kit with all the essential Arduino sensors.

    It comprises 37 Pcs of essential Arduino components. The kit includes the latest Arduino components that can be used to turn your idea into a real product.

    Tons of updated lessons and Arduino codes are available on Google and YouTube for free. It is extremely easy for Arduino fancier to control and use these modules. This kit will help you control the physical world with sensors.

  • UNI-T UT33B Plus Palm Size Digital Multimeter

    Original price was: ₨3,500.00.Current price is: ₨2,699.00.
    • Pocket-sized design for easy portability and on-the-go measurements.
    • Comprehensive measurement functions include voltage, current, resistance, diode testing, and continuity testing.
    • Large LCD display with backlight for clear and easy-to-read measurements.
    • Auto-ranging and manual ranging modes for flexible measurement options.
    • Safety features include overload protection and fused current inputs.
    • Battery saver function with auto power-off to extend battery life.
    • User-friendly interface with clearly labeled functions and range selection buttons.
    • Versatile applications in household, automotive, and electronic projects.
  • UNI-T UT33D+ Palm Size Digital Multimeter

    Original price was: ₨3,000.00.Current price is: ₨2,699.00.

    The new generation UT33+ series redefines the performance standards for entry-level digital multimeters. Our innovative industrial design ensures that these products can withstand 2 meters drop. The new LCD display layout provides a better user experience. This series ensures that users can work safely in CAT II 600V environment. Special features are, 2mF capacitance test (UT33A+); battery test (UT33B+); temperature measurement function (UT33C+); UT33D + for the NCV non-contact with electricity, resistance range up to 200M entry-level digital multimeter; is the electrical priority of the digital multimeter.