-
- 3.3-5.5V Input
- 1-1.5mA measuring current
- 40-50 uA standby current
- Humidity from 0-100% RH
- -40-80C Temperature Range
- +-2% RH accuracy
- +-0.5 degrees C
-
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -20A~ 20A
- Sensitivity: 100mV/A
- The current sensor chips: ACS712_ELC-20A.
- Pin 5V power supply, onboard power indicator.
- There is no the detection current through, the output voltage is VCC / 2.
- The module can be measure plus or minus 20 amps, corresponding to the analog output of 185 mV / A.
-
RF 315/433 Transmitter/Receiver Module
Original price was: ₨350.00.₨299.00Current price is: ₨299.00. Quick ViewTransmitter :
- Working voltage: 3V – 12V for max. power use 12V
- Working current: max Less than 40mA max, and min 9mA
- Resonance mode: (SAW)
- Modulation mode: ASK
- Working frequency: Eve 315MHz Or 433MHz
- Transmission power: 25mW (315MHz at 12V)
- Frequency error: +150kHz (max)
- Velocity: less than 10Kbps
So this module will transmit up to 90m in open area.
Receiver :
- Working voltage: 5.0VDC +0.5V
- Working current: 5.5mA max
- Working method: OOK/ASK
- Working frequency: 315MHz-433.92MHz
- Bandwidth: 2MHz
- Sensitivity: excel 100dBm (50)
- Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
-
PZEM-022 Open and Close CT 100A AC Digital Display Power Monitor Meter
Original price was: ₨5,000.00.₨3,999.00Current price is: ₨3,999.00. Quick View-
Operating Voltage: 80–260V AC
-
Measurement Current Range: 0.02–100A
-
Power Range: 0.5W–22,000W
-
Energy Range: 0–999kWh
-
Frequency Range: 45–65Hz
-
Power Factor Range: 0.00–1.00
-
Measurement Accuracy: Class 1.0
-
Nominal Power: 100A / 22000W
-
-
FSR402 Force Sensitive Resistor FSR
Original price was: ₨2,000.00.₨1,450.00Current price is: ₨1,450.00. Quick ViewThe FSR is made of 2 layers separated by a spacer. The more one presses, the more of those Active Element dots touch the semiconductor and that makes the resistance go down. FSRs are basically a resistor that changes its resistive value (in ohms Ω) depending on how much it is pressed. These sensors are fairly low cost, and easy to use but they’re rarely accurate. They also vary some from the sensor to sensor perhaps 10%. So basically when you use FSRs you should only expect to get ranges of response. While FSRs can detect weight, they’re a bad choice for detecting exactly how many pounds of weight are on them. However, for most touch-sensitive applications like “has this been squeezed or pushed and about how much” they’re a good deal for the money!
-
TSOP 1738 Sensor IR Receiver Plastic (SM0038)
Original price was: ₨90.00.₨59.00Current price is: ₨59.00. Quick View- Photo detector and preamplifier in one package
- Internal filter for PCM frequency
- Improved shielding against electrical field disturbance
- TTL and CMOS compatibility
- Output active low
- Low power consumption
- High immunity against ambient light
- Continuous data transmission possible (up to 2400 bps)
- Suitable burst length 10 cycles/burst
-
Arduino 28BYJ48 Stepper Motor
Original price was: ₨850.00.₨549.00Current price is: ₨549.00. Quick ViewArduino 28BYJ48 Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug. Motor: Diameter: 28mmVoltage: 5VStep angle: 5.625 x 1/64Reduction ratio: 1/64ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31x35mmPackage included:1 x ULN2003 driver board1 x 28BYJ-48 stepper motor Options:
-
HC-06 is a Bluetooth module designed for establishing short range wireless data communication between two microcontrollers or systems. The module works on Bluetooth 2.0 communication protocol and it can only act as a slave device. This is cheapest method for wireless data transmission and more flexible compared to other methods.
-
4 Way IR Line Tracking / Following Sensor Module
Original price was: ₨490.00.₨439.00Current price is: ₨439.00. Quick View- Operating Voltage: 3.3-5V
- Fixing Screw Hole: M3
- Distance setting from 1mm to 10cm
- Control Card Dimensions: 42x38x12mm
- Sensor Dimensions: 25x12x12mm
- Card Output: Digital
-
Arduino Starter Kit RFID Based
Original price was: ₨8,500.00.₨6,999.00Current price is: ₨6,999.00. Quick ViewArduino Starter Kit RFID Based walks you through the basics of using the Arduino & RFID in a hands-on way. You’ll learn through building several creative projects. The kit includes a selection of the most common and useful electronic components with a book of 15 projects. Starting from the basics of electronics to more complex projects, the kit will help you control the physical world with sensors and actuators.
This kit aims to bring Arduino together with RFID technology, which will support individual production. With this kit, you will be able to use RFID with the code you wrote in Arduino. You will be able to come up with a practical technology such as Arduino, a technology that many people like RFID are trying to get into and stay away from using. All of the components and components required for RFID technology are combined in this kit.
Radio Frequency Identification (RFID) is the given name to the technology used to identify objects using radio waves. An RFID microchip embedded in a tag, keychain or card communicates with the reader/writer module to transfer data.
-
DS3231 REAL TIME CLOCK MODULE – RTC
Original price was: ₨1,099.00.₨349.00Current price is: ₨349.00. Quick View- Size: 38mm (length) * 22mm (W) * 14mm (height)
- Operating voltage: 3.3 – 5 .5 V
- DS3231M at the core
- Clock Accuracy: 5ppm 0-40 C
- Two programmable alarms
- Programmable square-wave output
- DS3231M Datasheet
- LIR2032 / CR2032 backup battery holder for uninterrupted time management (battery not included)
- Wiring instructions (with Arduino Uno R3 for example):
- SCL A5
- SDA A4
- VCC 5V
- GND GND
-
Piezo Pack of 5 Large Pickups 45mm
Original price was: ₨500.00.₨430.00Current price is: ₨430.00. Quick ViewPiezo Pack of 5 Large Pickups 45mm Attach the round disc to the object that will be knocked on such as a door and measure the voltage across the two wires. Piezo elements can also produce sound when a voltage is applied across them. They convert between electricity and vibration in both ways; Vibration applied at the round end can be detected as a voltage across the wire leads and inversely, the voltage applied across the wire leads causes the round end to vibrate.
-
5V 1604 LCD 16×4 Character LCD Screen
Original price was: ₨1,000.00.₨799.00Current price is: ₨799.00. Quick View16X4 CHARACTER LCD 1604 Blue LCD DISPLAY is a dot-matrix liquid crystal display module specially used for displaying letters, numbers, symbols, etc. 16?4 LCD Display can display 4 lines with 16 characters in each line. Divided into 4-bit and 8-bit data transmission methods. 1604 Blue Character LCD provides rich command settings: clear display; cursor return to origin; display on/o; cursor on/o; display character ashes; cursor shift; display shift, etc.
-
IR receiver VS1838B TL1838 – 38KHz
Original price was: ₨90.00.₨70.00Current price is: ₨70.00. Quick View- IR Infrared Receiver 1838 TL1838 VS1838B 38Khz Diode
- Voltage; 2.7-5 .5 V
- Receiving distance; 13-15M
- Size: Pin length 21mm
- frequency: 38khz
- IR Infrared Receiver 1838 TL1838 VS1838B 38Khz DiodeVoltage; 2.7-5 .5 V
- Receiving distance; 13-15M
- Size: Pin length 21mm
- frequency: 38khz
-
Nodemcu WROOM ESP32 Wifi Based Microcontroller Development Board
Original price was: ₨1,500.00.₨1,049.00Current price is: ₨1,049.00. Quick View- Universal low power IoT sensor hub.
- Home automation.
- Universal low power IoT recorder.
- Mesh network.
- Video streaming of the camera.
- Industrial wireless control.
- OTT TV box / set-top box device.
- Baby monitor.
- Smart Socket.
- Sensor networks.
- Wi-Fi toys: Counters, toys, Anti-lost device.
- Wearable electronic products.
- Wi-Fi speech recognition device.
- Wi-Fi location-aware devices.
-
An NTC is commonly used as a temperature sensor, or in parallel with a circuit as an inrush current limiter.
-
GY521 MPU6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
Original price was: ₨490.00.₨399.00Current price is: ₨399.00. Quick ViewA 3-axis gyroscope and a 3-axis accelerometer are combined together on the same silicon die with an onboard Digital Motion Processor. Easy to get it fit into your project! It is very accurate, as GY-521 Mpu6050 Module contains 16-bits analog to digital conversion hardware for each channel. Therefor Three axis Gyrometer captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with the Arduino.
-
MQ2 MQ-2 SMOKE SENSOR MODULE
Original price was: ₨350.00.₨289.00Current price is: ₨289.00. Quick View- Operating voltage: 5V
- Analog output voltage: 0V to 5V
- Digital output voltage: 0V or 5V (TTL Logic)
- Preheat duration: 20 seconds
- Sensitivity range: 200 to 10,000 ppm
- Gases detected: LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide
- Dimensions: 3.6 x 2 x 1 cms
- Weight: 5 grams
-
PZEM-004T AC Voltage-Current Sensor with Open and Close Type Current Transformer
Original price was: ₨4,046.00.₨3,099.00Current price is: ₨3,099.00. Quick View- Working Voltage: 80~260VAC
- Test Voltage: 80~260VAC
- Rated power: 100A / 22000W
- Working Frequency: 45-65Hz
- Measurement accuracy: ±1.0%
- Board size: 18.5 × 3 × 2.2 cm / 2.87 × 1.18 × 0.9″
-
- Reverse Voltage(Vr): 5 V
- Reverse Leakage Current (Ir): 50A
- Forward Current (If): 25mA
- Peak Forward Current (Ifp): 100 mA
- Power Dissipation (P): 100 mW per Segment
- Operating Temperature (Topr): -40C to +80C
- Storage Temperature (Ttsg): -40C to +85C
- Lead Soldering Temperature: 260C
- Height: 70mm
- Width: 48mm
-
- Rated Load: 20Kg
- Rated Output: 1.0 ±0.15mV/V
- Zero Output: ±0.1mV/V
- Cree: 0.03%F.S./30min
- Input End: Red+, Black-
- Output End: Green+, White-
- Input Impedance: 1115±10% Ω
- Output Impedance: 1000±10% Ω
- Maximum working voltage: 15V DC
- Operating temperature range: -20~60°C
- Total Size: 80 x 13 x 13mm/3.14 x 0.51 x 0.51″(L x W x H)
-
- Operating voltage: 5V
- Provide both digital and analog output
- Adjustable sensitivity
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- Bolt holes for easy installation
- 3.2 cm x 1.4 cm x 1.0 cm
-
- Digital Output Hall-effect sensor.
- Operating voltage: typically 5V.
- Output Current: 25mA.
- It can be used to detect both the poles of a magnet.
- The output voltage is equal to the operating voltage.
- Operating temperature: -40C to 85C.
- Turn on and Turn off time is 2 sec each.
- Inbuilt reverse polarity protection.
- Suitable for Automotive and Industrial Applications.
-
DHT11 Temperature and Humidity Sensor
Original price was: ₨300.00.₨249.00Current price is: ₨249.00. Quick View- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0C to 50C
- Humidity Range: 20% to 90%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: 1C and 1%
-
- Working voltage: DC 3.3V-5V
- Working current: 20mA
- Operating temperature: -10~+50
- detection distance :2-40cm
- IO Interface: 4-wire interfaces (-/+/S/EN)
- Output signal: TTL level (low level there is an obstacle, no obstacle high)
- Adjustment: adjust multi-turn resistance 8. Effective angle: 35.7.
- Size: 28mmx23mm
-
- Material: FR4
- Length: 25mm
- Width: 11mm
- Height: 16mm
- Weight: 1.59g
- Operating Voltage: 5v DC
-
- Model: YF-S201
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Liters/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Liter: 450
- Durability: minimum 300,000 cycles
- Cable length: 15cm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 2.5″ x 1.4″ x 1.4″
-
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4×3 type 12 keys.
- Sticker can peel off for adhesive mounting.
- Used widely in industrial and home electronic equipment’s, instrument, etc.
- This allows a microcontroller to ‘scan’ the 7 output pins to see which of the 12 buttons is being pressed.
-
HCSR04 ultrasonic sensor Bracket
Original price was: ₨180.00.₨69.00Current price is: ₨69.00. Quick View- Thickness: 2.8 – 3.1 mm
- Inner diameter: 16 mm
- Fixing Hole Diameter: 3.8 mm
- Material: High Quality Imported Acrylic
- Colour: Blue
- Application: Stationary ultrasonic sensor modules and other products
-
DHT11 Humidity & Temperature Sensor
Original price was: ₨350.00.₨280.00Current price is: ₨280.00. Quick View- Dimension 28mm*12mm*10mm
- Main chip DHT11 huminity sensor
- Voltage: DC 5V
- Digital output
- Humidity Range: 2090%RH
- Humidity accuracy:5%RH
- Temperature range:0-60
- Temperature accuracy: 2
-
PZEM-022 CT 100A AC Digital Display Power Monitor Meter
Original price was: ₨4,500.00.₨2,999.00Current price is: ₨2,999.00. Quick View-
Operating Voltage: 80–260V AC
-
Measurement Current Range: 0.02–100A
-
Power Range: 0.5W–22,000W
-
Energy Range: 0–999kWh
-
Frequency Range: 45–65Hz
-
Power Factor Range: 0.00–1.00
-
Measurement Accuracy: Class 1.0
-
Nominal Power: 100A / 22000W
-
-
TTP223B Blue Touch Sensor 1-Ch-Capacitive Touch Sensor
Original price was: ₨250.00.₨95.00Current price is: ₨95.00. Quick View- Power supply voltage(VCC): 2.0, 3, 5.5 V.
- Output high VOH: 0.8VCC V
- Output low VOL: 0.3VCC V
- Response time (touch mode) : 60 mS
- Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V) : 8 mA
- Output pin pull-up current (@ VCC = 3V, VOH = 2.4V) : 4 mA
- Response time (low power mode) : 220 mS
- Size : 24 x 24 x 7.2 mm
-
50A SCT-013-000 Non-invasive AC Current Clamp Sensor
Original price was: ₨1,800.00.₨1,249.00Current price is: ₨1,249.00. Quick View- Input Current: 0~50A AC
- Output Mode: DC 0~1V
- Non-linearity:2-3%
- Build-in sampling resistance(RL): 62Ω
- Turn Ratio: 1800:1
- Resistance Grade: Grade B
- Work Temperature: -25°C ~ ﹢70°C
- Dielectric Strength(between shell and output): 1000V AC/1min 5mA
- Leading Wire in Length: 1m
- Open Size: 13mm x 13mm
-
7 in 1 Soil Integrated Sensor EC PH NPK Moisture Temperature Meter
Original price was: ₨38,000.00.₨28,999.00Current price is: ₨28,999.00. Quick View- High precision agriculture sensors, rapid response, good exchange ability
- Good tightness, corrosion resistance, the soil tester can be used in the soil for a long time.
- Flame retardant epoxy resin curing, completely waterproof, the soil tester can withstand strong external impact.
- Steel needles are made of high quality materials that can with stand long-term electrolysis , acid and alkali corrosion in soil.
-
4 Bits TM1637 Digital Tube LED 7 Segments Display Module
Original price was: ₨350.00.₨249.00Current price is: ₨249.00. Quick View4 Bits TM1637 Digital Tube LED 7 Segments Display Module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.
-
MAX31865 RTD PT100 Amplifier
Original price was: ₨2,700.00.₨1,599.00Current price is: ₨1,599.00. Quick View- Advantage: Handling all of your RTD needs.
- Strong point: Compensating 3 or 4-wire RTDs for better accuracy.
- Characteristic: Could be used with any Arduino or microcontroller.
- Feature: 3.3V regulator and level shifting.
- Feature: Could be used with any 2, 3, or 4-wire PT100 RTD.
-
SW-520D – Tilt Sensor Module
Original price was: ₨220.00.₨149.00Current price is: ₨149.00. Quick View- Using high-sensitivity switch SW 520D as the sensor.
- The module is equipped with fixed bolt hole for convenient installation.
- Using LM393 wide voltage comparator, clean signal, good waveform, strong driving ability with output of more than 15 mA.
- The working voltage of 3.3V to 5V.
- Small PCB size:3.2cm x 1.4cm.
- Digital output form: digital switch output (0 and 1).
-
Telko S063 Portable Door Wedge Guard
Original price was: ₨788.00.₨499.00Current price is: ₨499.00. Quick View- High output: 120DB alarm siren
- Standard 9 volt battery operation
- Required no special installation
- Rugged high impact ABS construction
- Provide alarm siren operation from contact with door or from movement vibration.
-
- Very low supply current
- Photodetector and preamplifier in one package
- Internal filter for PCM frequency
- Improved shielding against EMI
- Supply voltage: 2.5 V to 5.5 V
- Improved immunity against ambient light
- Insensitive to supply voltage ripple and noise
-
- Operating Voltage is 5V
- it is with Chinese font
- it has a blue backlight
- Controller used in it ST7920
- its Size is 93x70mm
- It displays 20 characters in 4 lines.
- Its input voltage range is 4.5V to 5.5V.
- The operating voltage for LCD is 5V Direct Current (DC).
- Its interface consists of 6800 8 bit parallel.
- Positive transflective is its display type.
- Its backlight consists of blue and green.
-
- It has a nice standard 0.1×0.1 prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- A IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- A surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out!
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
- It has a nice standard 0.1×0.1 prototyping grid with big pads
-
Arduino SD Card Reader Module
Original price was: ₨220.00.₨199.00Current price is: ₨199.00. Quick View- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V\
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
-
SIM800L GSM Module Micro Sim Card Board
Original price was: ₨1,799.00.₨1,049.00Current price is: ₨1,049.00. Quick View- Module models: SIM800L (latest module, performance than SIM900)
- Operating voltage: 3.7 to 4.2 V (peak current is 2A)
- Support network: China mobile, China Unicom
- Module size: 2.2 x 1.8cm
- TTL serial port can directly link to MCU. Don’t need a MAX232
- Power on automatic startup, automatic search network
- Onboard one channel indicator light (with signal slow flash, no signal quickly flash)
-
- The real-time clock counts minutes, seconds, date, hours, month day of the week, year and leap-year compensation upto 2100.
- 318 temporary data storage RAM
- Working current of 2.0V, less than 300nA
- Read / Write clock or RAM data with two kinds of mode of single-byte transfer mode and multi-byte character set
- 8 pin DIP package or optional 8 pin SOIC package based on the surface assembly
- Simple 3 wire interface
- Compatible with TTL Vcc=5V
- Double power supply pipe for main power and backup power supply.
-
XBee 2mW Wire Antenna – Series 2 (ZB)
Original price was: ₨15,000.00.₨8,799.00Current price is: ₨8,799.00. Quick ViewThis is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
-
Heart Rate Monitor ECG AD8232 Module + Leads
Original price was: ₨2,500.00.₨1,479.00Current price is: ₨1,479.00. Quick View- Supply voltage: DC 3.3V
- Output: Analog output
- Interface (connected to RA LA RL): 3PIN 2.54 pin or headset
- Size 36mm * 31mm * 18mm
- Operating temperature: -40C +85 C
-
Microphone Amplifier – MAX9814 w/ Auto Gain Control
Original price was: ₨800.00.₨449.00Current price is: ₨449.00. Quick View- The default ‘max gain’ is 60dB, but can be set to 40dB or 50dB by jumpering the Gain pin to VCC or ground.
- You can change the Attack/Release ratio, from the default 1:4000 to 1:2000 or 1:500.
- The ouput from the amp is about 2Vpp max on a 1.25V DC bias, so it can be easily used with any Analog/Digital converter that is up to 3.3V input. If you want to pipe it into a Line Input, just use a 1uF blocking capacitor in series.
-
W5500 Ethernet Network Module / Shield
Original price was: ₨1,500.00.₨1,099.00Current price is: ₨1,099.00. Quick View- Operating voltage: 2.97-3.63V
- Current draw: Typical: 128mA, Max: 200mA
- SPI clock frequency: Max: 80MHz
- Ethernet MAC: 10/100BASE-T
- PHY: 10BASE-T and 100BASE-T
- TCP/IP stack: TCP, UDP, IPv4, ICMP, ARP, IGMP, and PPPoE
- Hardware sockets: 8
- Internal buffer: 32KB
- Supports: SPI, WOL, and power down mode





























































































