-
- 3.3V, 5V, 12V, and adjustable output versions
- Adjustable version output voltage range, 1.2V to 37V ±4% max over line and load conditions
- Available in TO-220 and TO-263 packages
- Guaranteed 3A output load current
- Input voltage range up to 40V
- Requires only 4 external components
- Excellent line and load regulation specifications
- 150 kHz fixed frequency internal oscillator
- TTL shutdown capability
- Low power standby mode, IQ typically 80 µA
- High efficiency
- Uses readily available standard inductors
- Thermal shutdown and current limit protection
-
- A dual version of NE556 consists of two precision timers that operate in both monostable and astable modes.
- It is specified for operation from 4.5 V to 16 V.
- TTL compatible output which can source or sink current of up to 150mA.
- Adjustable duty cycle.
- It can produce a timing delay from microseconds to hours.
- The operating temperature range is from 0 to 70 degrees Celsius.
- It has temperature stability better than 0.005% per C.
-
-13%
KBL406 5-600V 4A Bridge Rectifier
Original price was: ₨45.00.₨39.00Current price is: ₨39.00. Quick ViewBridge rectifier diode with a 4A current rating.
-
-11%
KBPC3502 Bridge Rectifier Diode 35A 200V
Original price was: ₨200.00.₨179.00Current price is: ₨179.00. Quick ViewBridge rectifier diode with a 35A current rating.
-
N-Channel Power MOSFET provide the circuit designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness.
-
-15%
Out Of StockCenter Tapped Transformer 9V 0.4Amp
Original price was: ₨350.00.₨299.00Current price is: ₨299.00. Quick View- Input Voltage: 220V/AC
- Output Voltage: 9V/AC
- Output current: 0.4 A
- Power : 24 Watts
- Phase: Single Phase
- Frequency:50Hz
- Cooling Type: Dry Type/Air Cooled
- Material: CRGO core and Super enameled copper wire
- Dimensions:85×42.6x50mm
-
-14%
Center Tapped Transformer 12V 2.5AMP
Original price was: ₨520.00.₨449.00Current price is: ₨449.00. Quick View- Step-down Centre tapped Transformer
- Input Voltage: 220V AC at 50Hz
- Output Voltage: 12V, 12V or 0V
- Output Current: 2.5A
- Vertical mount type
- Low cost and small package
-
-20%
8051 Atmel AT89C51 Microcontroller 8-bit
Original price was: ₨500.00.₨399.00Current price is: ₨399.00. Quick View- Compatible with MCS-51 Products
- 4K Bytes of In-System Reprogrammable Flash Memory
- Endurance: 1,000 Write/Erase Cycles
- Fully Static Operation: 0 Hz to 24 MHz
- Three-Level Program Memory Lock
- 128 x 8-Bit Internal RAM
- 32 Programmable I/O Lines
- Two 16-Bit Timer/Counters
- Six Interrupt Sources
- Programmable Serial Channel
- Low Power Idle and Power Down Modes
-
The CD4024 is a 7-stage ripple-carry binary counter. Buffered outputs are externally available from stages 1 through 7. The counter is reset to its logical 0 stage by a logical 1 on the reset input. The counter is advanced one count on the negative transition of each clock pulse.
-
- High-Voltage Types (20V Rating)
- CD4073BMS Triple 3-Input AND Gate
- CD4081BMS Quad 2-Input AND Gate
- CD4082BMS Dual 4-Input AND Gate
- Medium Speed Operation: tPLH, tPHL = 60ns (typ) at VDD = 10V
- 100% Tested for Quiescent Current at 20V
- Maximum Input Current of 1A at 18V Over Full Package Temperature Range; 100nA at 18V and +25oC
-
- Package Type: TO-220
- Transistor Type: N Channel
- Max Voltage Applied From Drain to Source: 55V
- Max Gate to Source Voltage Should Be: 20V
- Max Continues Drain Current is : 49A
- Max Pulsed Drain Current is: 160A
- Max Power Dissipation is: 94W
- Minimum Voltage Required to Conduct: 2V to 4V
- Max Storage & Operating temperature Should Be: -55 to +170 Centigrade
-
-22%
Variable resistor 50K Potentiometer / Variable Resistor
Original price was: ₨50.00.₨39.00Current price is: ₨39.00. Quick ViewVariable resistor 50K Potentiometer / Variable Resistor (50K Ohm) is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer. The potentiometer essentially functions as a variable voltage divider. The resistive element can be seen as two resistors in series(potentiometer resistance), where the wiper position determines the resistance ratio of the first resistor to the second resistor. A potentiometer is also commonly known as a potentiometer or pot. The most common form of potmeter is the single turn rotary potmeter. This type of pot is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, wirewound, conductive plastic or metal film.
-
-36%
A crystal oscillator is an electronic oscillator circuit that uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a precise frequency. This frequency is often used to keep track of time, as in quartz wristwatches, to provide a stable clock signal for digital integrated circuits, and to stabilize frequencies for radio transmitters and receivers. The most common type of piezoelectric resonator used is the quartz crystal, so oscillator circuits incorporating them became known as crystal oscillators, but other piezoelectric materials including polycrystalline ceramics are used in similar circuits.
-
-15%
This device contains four independent gates each of which performs the logic exclusive-OR function.
-
- Package Type: TO-92
- Transistor Type: NPN
- Max Collector Current(IC): 30mA
- Max Collector-Emitter Voltage (VCE): 20V
- Max Collector-Base Voltage (VCB): 30V
- Max Emitter-Base Voltage (VBE): 5V
- Max Collector Dissipation (Pc): 300 Milliwatt
- Max Transition Frequency (fT): 120 MHz
- Minimum & Maximum DC Current Gain (hFE): 35 to 125
- Max Storage, Operating & Junction temperature range: -65 to +150 Centigrade
-
-20%
2SA1941 bipolar transistor p-n-p type transistor. Collector-Emitter Voltage: -140 V Collector-Base Voltage: -140 V Emitter-Base Voltage: -5 V Collector Current: -10 A Collector Dissipation – 100 W DC Current Gain (hfe) – 55 to 160 Transition Frequency – 30 MHz Operating and Storage Junction Temperature Range -55 to +150 ?C
-
Optocoupler 817 QUAD contains an IRED optically coupled to a phototransistor. It is packaged in a 4pin DIP, available in wide-lead spacing option and SMT gullwing lead-form option. Input-output isolation voltage(rms) is 5.0kV. Collector-emitter voltage is 80V(*) and CTR is 50% to 600% at input current of 5mA.
-
The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected.
-
-31%
TLP250 MOSFET IGBT DRIVER TLP-250
Original price was: ₨360.00.₨249.00Current price is: ₨249.00. Quick View- Input threshold current: IF=5mA(max.)
- Supply current (ICC): 11mA(max.)
- Supply voltage (VCC): 1035V
- Output current (IO): 1.5A (max.)
- Switching time (tpLH/tpHL): 1.5s(max.)
- Isolation voltage: 2500Vrms(min.)
- UL recognized: UL1577, file No.E67349
- Option (D4) type
- VDE approved: DIN VDE0884/06.92,certificate No.76823
- Maximum operating insulation voltage: 630VPK
- Highest permissible over voltage: 4000VPK
- Creepage distance: 6.4mm(min.)
- Clearance: 6.4mm(min.)
-
-18%
The LF33CV is a very low drop voltage regulator. It has an output voltage of 3.3 V and a output current of 500 mA. Input voltage range 2.5V to 16V. It is suitable for low noise, low power applications and specially in battery powered systems.
-
-17%
LM386 LM-386 Audio Amplifier Chip
Original price was: ₨35.00.₨29.00Current price is: ₨29.00. Quick ViewLM386 is a widely used audio amplifier IC manufactured in 8 pin dip, VSSOP, SOIC and other packages. The IC is basically designed for low voltage commercial applications, apart from commercial applications it is also a famous IC among electronic hobbyists and experimenters. The internal gain of the IC is set to 20 but it can be adjusted by connecting a resistor and a capacitor in series between the pin number 1 and 8, by this procedure the user can adjust the gain between 20 to 200. Due to the small size, low quiescent current and low voltage requirements this IC is ideal to use in wide variety of portable battery operated applications and devices.
-
-27%
Atmega8 Microcontrollers IC 8Kbytes
Original price was: ₨899.00.₨659.00Current price is: ₨659.00. Quick ViewThe Atmel AVR ATmega8 is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8 achieves throughputs approaching 1MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed.
-
This NPN Bipolar Darlington Transistor is designed for use in switching applications, such as print hammer, relay, solenoid and lamp drivers.
-
This IC is a 16-Bit SPI I/O Expander with Serial Interface. This IC has 25mA sink/source capability per I/O.
-
The 2N2905 from Multicomp Pro is a through-hole, silicon planar PNP low power bipolar transistors in a TO-39 metal can package. These are general-purpose transistors suitable for switching applications.
-
The 4077 is a quad 2-input EXCLUSIVE-NOR gate. The outputs are fully buffered for the highest noise immunity and pattern insensitivity to output impedance. The 4077 operates over a recommended VDD power supply range of 3 V to 15 V referenced to VSS (usually ground). Unused inputs must be connected to VDD, VSS, or another input.
-
- High Speed Binary Ripple Carry Counter
- Separate Reset Input Pin
- Wide Operating Voltage Range: 2.0 to 6.0 V
- Output Drive up to 10 LS-TTL Loads
- Equivalent to CD4060
-
-46%
- Type Designator: 2SC2331
- Material of transistor: Si
- Polarity: NPN
- Maximum collector power dissipation (Pc), W: 1
- Maximum collector-base voltage |Ucb|, V: 80
- Maximum collector-emitter voltage |Uce|, V: 60
- Maximum emitter-base voltage |Ueb|, V: 8
- Maximum collector current |Ic max|, A: 0.7
- Transition frequency (ft), MHz: 30
- Collector capacitance (Cc), pF: 8
- Forward current transfer ratio (hFE), min: 40
- Noise Figure, dB: –
- Package of 2SC2331 transistor: TO92
-
-22%
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer. The potentiometer essentially functions as a variable voltage divider. The resistive element can be seen as two resistors in series(potentiometer resistance), where the wiper position determines the resistance ratio of the first resistor to the second resistor. A potentiometer is also commonly known as a potentiometer or pot. The most common form of potmeter is the single turn rotary potmeter. This type of pot is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, wirewound, conductive plastic or metal film.
-
-18%
- Identical in Function to the 74LS93 with Different Pin Arrangement
- Contains Four Master-Slave Flips-Flops together with a Binary Counter
- Gated Zero Reset
- Fast Propagation Speeds
- Low Power Dissipation
-
-13%
- 5V Negative Voltage Regulator
- Output Voltage: -5V
- Output Current: 1.5A
- Minimum Input Voltage is 7V
- Maximum Input Voltage is 25V
- Operating current(IQ) is 5mA
- Internal Thermal Overload and Short circuit current limiting protection is available.
- Junction Temperature maximum 125 degree Celsius
- Available in TO-220 and KTE package
-
- Op-amp coupled with MOSFET at output
- Wide power supply Range
- Singe supply – 5V to 16V
- Dual supply – ±2.5V to ±8V
- Input Terminal current: 1mA
- Maximum Output Voltage: 13.3V
- Maximum source current: 22mA
- Maximum sink current: 20mA
- Supply current: 10mA
- Common Mode Rejection Ration (CMRR): 80dB
-
-40%
LM-337 LM337 Variable Negative -VE Voltage Regulator IC
Original price was: ₨65.00.₨39.00Current price is: ₨39.00. Quick View- Used for Positive voltage regulations
- Variable power supply
- Current limiting circuits
- Reverse polarity circuits
- Commonly used in Desktop PC, DVD and other consumer products
- Used in motor control circuits
-
-21%
SCR C106 C106 Series – SCR TO-255AA 4A
Original price was: ₨75.00.₨59.00Current price is: ₨59.00. Quick View- Glassivated Surface for Reliability and Uniformity
- Power Rated at Economical Prices
- Practical Level Triggering and Holding Characteristics
- Flat, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability
- Sensitive Gate Triggering
- Device Marking: Device Type, e.g., C106B, Date Cod
-
-53%
SG3525 / KA3525 PWM Controller IC in Pakistan
Original price was: ₨190.00.₨89.00Current price is: ₨89.00. Quick View- DUAL SOURCE/SINK OUTPUT DRIVERS
- LATCHING PWM TO PREVENT MULTIPLE PULSES
- PULSE-BY-PULSE SHUTDOWN
- INTERNAL SOFT-START
- 8 TO 35 V OPERATION
- 100 Hz TO 500 KHz OSCILLATOR RANGE
- 5.1 V REFERENCE TRIMMED TO 1 %
- ADJUSTABLE DEADTIME CONTROL
- INPUT UNDERVOLTAGE LOCKOUT WITH HYSTERESIS
- SEPARATE OSCILLATOR SYNC TERMINAL
-
-30%
74HC164 8-Bit Parallel-Out Shift Register
Original price was: ₨100.00.₨70.00Current price is: ₨70.00. Quick ViewFeatures/Specs:
Wide Supply Voltage Range from 2.0V to 6.0V
Sinks or Sources 4mA at VCC = 4.5V
CMOS Low Power Consumption
Schmitt Trigger Action at all Inputs
ESD Protection Exceeds JESD 22v 200-V Machine Model (A115)
2000-V Human Body Model (A114)
Exceeds 1000-V Charged Device Model (C101)
Range of Package Options SO-14 and TSSOP-14
Totally Lead-Free & Fully RoHS Compliant
Halogen and Antimony Free. Green Device
-
-33%
D-Type Flip-Flop 74HC175 DIP16 – SN74HC175N
Original price was: ₨60.00.₨40.00Current price is: ₨40.00. Quick View- Outputs can drive up to 10 LSTTL loads
- Contain four flip-flops with double-rail outputs
- 80A Maximum low power consumption
- 13ns Typical tpd
- 4mA Output drive at 5V
- 1A Maximum low input current
-
-15%
Good Quality Transformer, power supplies for all kinds of project and circuit boards available at electronation.pk in best price
-
-23%
Good Quality Transformer, power supplies for all kinds of project and circuit boards.
-
Bridge rectifier diode with a 6A current rating.
-
This is a monostable multivibrator or pulse generator.
-
74HC540 is a 20 Pin Octal 3-state Inverting Buffer IC having 2V to 6V Operating Voltage range with 6mA output current. The 3-STATE buffers utilize advanced silicon-gate CMOS technology. They possess high drive current outputs which enable high speed operation even when driving large bus capacitances.
-
Texas Instruments SN7414 Series Inverters are available at ElectroNation.
-
This Power MOSFET provides the circuit designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness.
-
-13%
The AT89C52 is a lowe power, high performance CMOS 8-bit microcontroller with 8K bytes of Flash programmable and reaseable read only memory (PEROM). The on-chip flash allows the program memory to be reprogrammed in-syetem.
-
The Exclusive OR gates are monolithic complementary MOS (CMOS) integrated circuits constructed with N-Channel and P-Channel enhancement mode transistors. All inputs are protected against static discharge with diodes to VDD and VSS.
-
The TL431 is three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and military temperature ranges. The output voltage can be set to any value between Vref (approximately 2.5 V) and 36 V, with two external resistors. These devices have a typical output impedance of 0.2 .
-
- Guaranteed zero reading for 0 V input on all scales
- True polarity at zero for precise null detection
- 1pA typical input current
- True differential input and reference, direct display drive – LED lCL7107
- Low noise – less than 15 VP-P
- On-chip clock and reference
- Low power dissipation – typically less than 10mW
- No additional active circuits required
- Enhanced display stability
- Pb-free (RoHS compliant)