Arduino & IOT Boards

Default sorting
Show
48
  • -22%
    Out Of Stock

    3.5″ IPS TFT LCD for Arduino MEGA2560

    Display
    (0)
    Original price was: ₨5,000.00.Current price is: ₨3,899.00. Quick View
    • Screen size 3.5″ – 480 X 320 Pixels
    • Support Arduino Mega2560 directly
    • Control IC: ILI9846
    • Compatible with 3.3/5V operation voltage level
    • Full-angle IPS TFT panel
    • With SD card Socket
    • Interface: 16 Bit parallel interface
  • -32%

    Force Sensitive Resistor – Small

    Flex & Force
    (0)
    Original price was: ₨1,899.00.Current price is: ₨1,299.00. Quick View

    This is a small force-sensitive resistor. It has a 0.16″ (4 mm) diameter active sensing area. This FSR from Interlink Electronics will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR, its resistance will be larger than 1MΩ, with full pressure applied the resistance will be 2.5kΩ.

    Two pins extend from the bottom of the sensor with a 0.1″ pitch making it breadboard-friendly.

    These sensors are simple to set up and great for sensing pressure, but they aren’t incredibly accurate. Use them to sense if it’s being squeezed, but you may not want to use it as a scale.

  • Out Of Stock

    XBee Pro 60mW Wire Antenna

    Communication Modules
    (0)
    ₨6,799.00 Quick View

    INTRODUCTION

    This is the very popular 2.4GHz XBee XBP24-AWI-001 module from Digi (formerly known as Maxstream). The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
  • -41%

    XBee 2mW Wire Antenna – Series 2 (ZB)

    Communication Modules
    (0)
    Original price was: ₨15,000.00.Current price is: ₨8,799.00. Quick View

    This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.

  • -17%

    SCT-013-000 Non-invasive AC Current Clamp Sensor 20A

    Current & Voltage
    (0)
    Original price was: ₨1,500.00.Current price is: ₨1,250.00. Quick View

    AC Current Signal Conversion Module

    • Input Voltage (VCC): 3.3V-5.5V
    • Interface: Gravity Analog (PH2.0-3P，analog voltage output 0.2-2.8V DC)
    • AC Voltage Input Range: 0-1V (AC RMS)
    • Relative Error: +/- 4%
    • Dimension: 32×27 mm
    • Weight: 5g

    Open Type AC Transformer Probe

    • AC Current Range: 0-20A
    • Signal Output (standard Φ3.5mm 3P plug): 0-1V AC voltage, linear corresponding range 0-20A
    • Accuracy: ±1%
    • Non-linearity: ≤±0.2%
    • Frequency Range: 50Hz~1kHz
    • Cable Length: 1m
    • Working Temperature: -25 ℃~+70 ℃
    • Opening Size: 13×13 mm / 0.51×0.51 in
    • Weight: 50g
  • Out Of Stock

    Gravity: 80cm Arduino Infrared Proximity Sensor

    Accelero, Gyro. IMU, Magneto
    (0)
    ₨890.00 Quick View

    INTRODUCTION

    This is an infrared distance switch. It has an adjustable detection range, 3cm – 80cm. It is small, easy to use, assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line, etc. Infrared wave length is part of the Sun’s natural light spectrum. While is a nice fit for indoor projects, outdoors with plenty of sun light and reflective surfaces on it’s sight is not adviced. It’s incredibly repurposable and can be used for a lot of different projects. The adjustable screw on it’s back makes it very convenient for different purposes. Digital read on your Arduino pin and you are ready to go. Good sensor choice for quick prototyping.

    Use it on a robot for wall detection and wall follower, or as some of the projects listed below as a trigger system. It’s round shape with the screwable holders make it a good choice for a home made assembled robot, with a hole of it’s diameter and the holders you can place it aiming at different positions on a robot. Or even place it near your PC to turn on and off your monitor.

  • -30%
    Out Of Stock

    XBee 1mW Wire Antenna

    Communication Modules
    (0)
    Original price was: ₨6,500.00.Current price is: ₨4,549.00. Quick View

    INTRODUCTION

    This is the very popular 2.4GHz XBee module from Digi (formally Maxstream). These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
    Pair a couple of these XBees with a Regulated Explorer, and a USB Explorer and you’ve got a great gift for that special electronics geek!
  • -28%
    Out Of Stock

    Digispark – The tiny, Arduino usb dev board

    Arduino & IOT Boards
    (0)
    Original price was: ₨620.00.Current price is: ₨449.00. Quick View

    The micro-sized, Arduino enabled, usb development board – cheap enough to leave in any project!

    Digispark?is an ATtiny85 based microcontroller development board come with USB interface.?Coding is similar to Arduino, and it use the familiar Arduino IDE for development.

  • Out Of Stock

    Telemetry 3DR TTL

    Communication Modules
    (0)
    ₨3,800.00 Quick View

    The Radio telemetry system base on 3DR Radio system and 100% compatible.

    It’s designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. Its available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).

    The system provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.

    Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.

  • -20%

    Xbee shield V03

    Communication Modules
    (0)
    Original price was: ₨5,000.00.Current price is: ₨3,999.00. Quick View
    This shield V03 can achieve a simple two crunodal ZigBee network, achieve wireless communication between Ardu, and allows the Ardu to wireless communicate over a modified ZigBee protocol using the popular XBee module.
    It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.
  • Out Of Stock

    ZigBee XCore2530 1500M

    Communication Modules
    (0)
    ₨1,950.00 Quick View

    ZigBee module, features the CC2530F256 onboard, farther communication distance with PA

    Overview

    XCore2530 is a ZigBee module based on CC2530F256.

    Basically this module can be used in two aspects :

    • Develop application with the provided firmware
      Combined with our provided firmware, this is a simple ZigBee wireless UART module, just as easy to use as any other UART module, and requires NO knowledge about the complicate ZigBee Specification
    • Develop your own firmware
      In this case, you should start from the very underlying to create your solution, what’s more, debuggers (like CC Debugger) and knowledge about ZigBee Specification are also required
  • -2%

    EasyVR Shield 3.0 – Voice Recognition Shield

    Mic/Voice Recognition
    (0)
    Original price was: ₨10,000.00.Current price is: ₨9,799.00. Quick View

    Do you make time to talk to your Arduino? Maybe you should! The EasyVR Shield 2.0 is a voice recognition shield for Arduino boards integrating an EasyVR module. It includes all of the features of the EasyVR module in a shield form factor that simplifies connection to the Arduino main board and PC.

    EasyVR 2.0 is a multi-purpose speech recognition module designed to add versatile, robust and cost-effective speech and voice recognition capabilities to virtually any application. EasyVR is the third-generation version of the successful VRbot module and builds on the features and functionality of its predecessor. In addition to the EasyVR 2.0 features like 28 user-defined Speaker Dependent (SD) triggers and 28 custom speaker independent (SI) commands, the shield has additional connectors for the microphone input, an 8 ohm speaker output, audio line-out/headphone jack, and access to the I/O pins of the EasyVR module. A programmable LED is also included to show feedback during recognition tasks.

  • -15%

    RF 315/433 Transmitter/Receiver Module

    Communication Modules
    (0)
    Original price was: ₨350.00.Current price is: ₨299.00. Quick View

    Transmitter :

    • Working voltage: 3V – 12V for max. power use 12V
    • Working current: max Less than 40mA max, and min 9mA
    • Resonance mode: (SAW)
    • Modulation mode: ASK
    • Working frequency: Eve 315MHz Or 433MHz
    • Transmission power: 25mW (315MHz at 12V)
    • Frequency error: +150kHz (max)
    • Velocity: less than 10Kbps

    So this module will transmit up to 90m in open area.

    Receiver :

    • Working voltage: 5.0VDC +0.5V
    • Working current: 5.5mA max
    • Working method: OOK/ASK
    • Working frequency: 315MHz-433.92MHz
    • Bandwidth: 2MHz
    • Sensitivity: excel 100dBm (50)
    • Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
  • -62%

    NRF24L01 2.4GHz Wireless Transceiver Module

    Communication Modules
    (0)
    Original price was: ₨650.00.Current price is: ₨249.00. Quick View
    • Worldwide 2.4GHz ISM band operation Free license to use.
    • 126 RF channels.
    • High air data rate: 250kbps, 1 and 2Mbps.
    • Transmitter: 11.3mA at 0dBm output power.
    • Receiver: Fast AGC for improved dynamic range.
    • Receiver: Integrated channel filters.
    • Enhanced ShockBurst:1 to 32 bytes dynamic payload length,6 data pipe MultiCeiver for 1:6 star networks.
    • Host Interface:4-pin hardware SPI,3 separate 32 bytes TX and RX FIFOs.
    • Low Power Management:1.9 to 3.6V supply range.
    • GFSK modulation.
    • Auto packet transaction handling.
    • Easy to design.
    • Small size:15mm*29mm.
  • -11%
    5v 8 Channel Relay Module Relay Board Relay Arduino Relay Module

    5v 8 Channel Relay Module Relay Board Relay Arduino Relay Module

    Module
    (0)
    Original price was: ₨900.00.Current price is: ₨799.00. Quick View
    1. Imported high-quality double-sided compact PCB.
    2. Opto-isolated inputs mean your digital electronics are safe and noise-free.
    3. This relay module is 5V active low.
    4. It is an 8-channel relay interface board, which can controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
    5. It is also able to control various appliances and other equipment with a large current.
    6. 5v Relay output maximum contact is AC250V 10A and DC30V 10A.
    7. The standard interface can be directly connected with microcontrollers.
    8. Red working status indicator lights are conducive to safe use.
    9. Widely used for all MCU control, industrial sector, PLC control, and smart home control.
  • Out Of Stock

    Infrared Proximity Sensor – GP2Y0A02YK0F Sharp Long Range

    Distance & Proximity
    (0)
    ₨1,250.00 Quick View

    Infrared proximity sensor made by Sharp. Part # GP2Y0A02YK0F has an analog output that varies from 2.8V at 15cm to 0.4V at 150cm with a supply voltage between 4.5 and 5.5VDC. The sensor has a Japanese Solderless Terminal (JST) Connector. We recommend purchasing the related pigtail below or soldering wires directly to the back of the module.

    This sensor is great for sensing objects up to 5 feet away!

  • Out Of Stock

    Infrared Proximity Range – GP2Y0A41SK0F Sharp Short Range

    Distance & Proximity
    (0)
    ₨2,200.00 Quick View

    Infrared Proximity Range – GP2Y0A41SK0F Sharp Short Range Sharp infrared distance sensor makes continuous distance readings and outputs an analog voltage proportional to an objects range. Working range of 1.5  to 12  (4 cm to 30 cm). Kit includes wires and connector. This model is a direct replacement for the discontinued Sharp GP2D120.

  • Out Of Stock

    Infrared Proximity Sensor – GP2Y0A21Y Sharp Mid Range

    Distance & Proximity
    (0)
    ₨2,450.00 Quick View

    Infrared proximity sensor made by Sharp. Part # GP2Y0A21YK has an analog output that varies from 3.1V at 10cm to 0.4V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. We recommend purchasing the related pigtail below or soldering wires directly to the back of the module.

  • -20%
    Out Of Stock

    XBee Pro 60mW PCB Antenna – Series 1

    Communication Modules
    (0)
    Original price was: ₨7,500.00.Current price is: ₨5,999.00. Quick View

    This is the very popular 2.4GHz XBee XBP24-ACI-001 module from Digi. The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.

  • -17%
    Out Of Stock

    XBee 2mW PCB Antenna – Series 2 (ZigBee Mesh)

    Communication Modules
    (0)
    Original price was: ₨6,000.00.Current price is: ₨4,999.00. Quick View

    This is the XBee XB24-Z7CIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
    These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
    This Xbee also has a chip antenna which is basically a small chip that acts as an antenna. Quick, easy, cheap, and not in the way.

  • -62%

    HCSR04 ultrasonic sensor Bracket

    Distance & Proximity
    (0)
    Original price was: ₨180.00.Current price is: ₨69.00. Quick View
    • Thickness: 2.8 – 3.1 mm
    • Inner diameter: 16 mm
    • Fixing Hole Diameter: 3.8 mm
    • Material: High Quality Imported Acrylic
    • Colour: Blue
    • Application: Stationary ultrasonic sensor modules and other products
  • -41%

    Heart Rate Monitor ECG AD8232 Module + Leads

    Heart Rate And Muscle Sensors
    (0)
    Original price was: ₨2,500.00.Current price is: ₨1,479.00. Quick View
    • Supply voltage: DC 3.3V
    • Output: Analog output
    • Interface (connected to RA LA RL): 3PIN 2.54 pin or headset
    • Size 36mm * 31mm * 18mm
    • Operating temperature: -40C  +85 C
  • Out Of Stock

    Sensor Cable – Electrode Pads

    Heart Rate And Muscle Sensors
    (0)
    ₨1,300.00 Quick View

    This is simple three conductor sensor cable with electrode pad leads. These cables are 24″ long and feature a 3.5mm audio jack connector on one end with snap style receptacles for biomedical sensor pads. Each cable comes in a red/blue/black set. Dimensions: 24″ Long.

  • -38%
    Out Of Stock

    Single Lead Heart Rate Monitor ECG – AD8232

    Heart Rate And Muscle Sensors
    (0)
    Original price was: ₨2,750.00.Current price is: ₨1,699.00. Quick View
    1. Operating Voltage – 3.3V
    2. Analog Output
    3. Leads-Off Detection
    4. Shutdown Pin
    5. LED Indicator
    6. 3.5mm Jack for Biomedical Pad Connection or Use 3 pin header
  • -46%

    Biomedical Sensor Pad (10 pack)

    Heart Rate And Muscle Sensors
    (0)
    Original price was: ₨1,300.00.Current price is: ₨699.00. Quick View

    This is a 10 pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are perfect for short-term monitoring of Neurofeedback and Biofeedback purposes. They are to be used once and are very handy because of integrated, latex-free gel. Each pad adheres very well to the skin and the snap connector can be pushed on or removed from the electrode lead with no issue.

  • -33%

    MQ3 MQ-3 Gas Sensor Module

    Gas Sensor
    (0)
    Original price was: ₨490.00.Current price is: ₨329.00. Quick View
    1. Model No.: MQ-3
    2. Dimensions: 36 x 20 x 21 mm (LxWxH)
    3. Weight: 6gm
    4. Heater voltage: 50.2V (AC DC)
    5. Loop voltage: 24V (DC)
    6. Load resistance: adjustable
    7. Heating Resistance: 31 3 (Room temperature)
    8. Heating Power: 900mW
    9. Surface thermal resistance: 2Kohm-20Kohm (0.4mg/L alcohol)
    10. Sensitivity: Rs (in air)/Rs (0.4mg/L alcohol) 5
    11. Working temperature: 20 degrees 2 degree
    12. Humidity: 65% 5%RH
    13. Signal output light indicator.
    14. Analog and level signal output.
    15. TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module).
    16. The carbon monoxide detection with better sensitivity.
    17. Has a long service life and reliable stability.
    18. Rapid response recovery features.
  • -44%

    Microphone Amplifier – MAX9814 w/ Auto Gain Control

    Others
    (0)
    Original price was: ₨800.00.Current price is: ₨449.00. Quick View
    • The default ‘max gain’ is 60dB, but can be set to 40dB or 50dB by jumpering the Gain pin to VCC or ground.
    • You can change the Attack/Release ratio, from the default 1:4000 to 1:2000 or 1:500.
    • The ouput from the amp is about 2Vpp max on a 1.25V DC bias, so it can be easily used with any Analog/Digital converter that is up to 3.3V input. If you want to pipe it into a Line Input, just use a 1uF blocking capacitor in series.
  • -18%

    BMP180 – Atmospheric Pressure Sensor

    Pressure
    (0)
    Original price was: ₨300.00.Current price is: ₨245.00. Quick View
    • 1.8V to 3.6V Supply Voltage
    • Low power consumption  0.5uA at 1Hz
    • I2C interface
    • Max I2C Speed: 3.5Mhz
    • Very low noise  up to 0.02hPa (17cm)
    • Full calibrated
    • Pressure Range: 300hPa to 1100hPa (+9000m to -500m)
    • Weight: 1.18g
    • Size: 21mm x 18mm
  • -39%

    Pressure Sensor MPX5700AP

    Pressure
    (0)
    Original price was: ₨9,000.00.Current price is: ₨5,499.00. Quick View
    1. On-chip signal conditioned, temperature compensated and calibrated
    2. 2.5% maximum error over 0°C to 85°C
    3. Ideally suited for microprocessor or microcontroller-based systems
    4. Patented silicon shear stress-strain gauge
    5. Pressure ranges from 15KPa to 700KPa
    6. Supply voltage ranges from 4.75VDC to 5.25VDC
    7. Sensitivity of 6.4mV/KPa
    8. Response time of 1ms
    9. Durable epoxy unibody element
    10. Operating temperature ranges from -40°C to 125°C
  • -11%

    MQ7 MQ-7 Gas Sensor Detection Module

    Gas Sensor
    (0)
    Original price was: ₨450.00.Current price is: ₨399.00. Quick View
    • Product Name: Gas Sensor Module;
    • Model: MQ-7;
    • Type: Analog
    • Detecting Type : Carbonic Oxide(Co);
    • Rated Voltage: DC 5V;
    • Rated Current: 180mA
    • Detecting Range: 100-1000ppm;
    • Pin Quantity: 4;
    • Pin Spacing: 1.8mm/ 0.07″
    • Pin Definition: AO-analog Output, DO-Digital Output, GND- Ground, VCC-Voltage To Current Converter ;
    • Total Size: 35 x 20 x 21mm/ 1.4″ x 0.79″ x 0.83″ (L*W*H)
  • -10%
    Out Of Stock

    ACS712 Current Sensor 30A

    Current & Voltage
    (0)
    Original price was: ₨400.00.Current price is: ₨359.00. Quick View

    ACS712 Current Sensor 30A current sensor board is based on the Allegro ACS712ELCTR-30A bi-directional hall-effect current sensor chip that detects positive and negative flowing currents in the range of minus 30 Amps to positive 30 Amps. The board operates at 5V DC and the current flow through the sensor is converted to an output voltage starting at 1/2Vcc (or 2.5V) for no current flow and moves up 66mV per amp for positive current or down -66mV per amp for negative current.

  • -31%

    Dual-axis XY Joystick Module for Arduino

    Arduino & IOT Boards
    (0)
    Original price was: ₨230.00.Current price is: ₨159.00. Quick View
    • Dimensions: 40 x 27 x 15 (LxWxH) mm
    • Weight: 10gm (without Hat).
    • 2.54mm pin interface leads
    • Operating Voltage: 5V.
    • Long service life and stable performance
    • Standard interface and electronic building blocks
    • Widely use in Arduino DIY projects
    • Cross rocker as a two-way 10K resistor, with the rocker in a different direction
  • Out Of Stock

    10 DOF IMU Sensor

    Accelero, Gyro. IMU, Magneto
    (0)
    ₨1,850.00 Quick View

    3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.

    ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.

  • -13%
    Out Of Stock

    Flex Sensor 4.5″

    Flex & Force
    (0)
    Original price was: ₨4,000.00.Current price is: ₨3,499.00. Quick View
    • Thickness: 0.4mm
    • Trigger Force: 20g, triggered (default resistance<200kΩ)
    • Pressure Measuring Range: 20g~6kg
    • Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz)
    • Initial Resistance: >10MΩ
    • Activation Time: <0.01S
    • Operating Temperature: -40℃~+85℃
    • Lifespan: >1million times
    • Hysteresis: +10%，(RF+ -RF-)/FR+，1000g Force
    • Response Time: <10ms
    • Drift: <5%, 2.5Kg Force, Static load 24H
  • -25%

    Load Sensor – 50kg

    Sensors
    (0)
    Original price was: ₨600.00.Current price is: ₨449.00. Quick View
    • Capacity: 40-50kg
    • Comprehensive Error: 0.05mv/v
    • Output Sensitivity: 1.0 0.1mv/v
    • Nonlinearity: 0.03%FS
    • Repeatability: 0.03%FS
    • Hysteresis: 0.03%FS
    • Creep: 0.03 (3min)%FS
    • Zero Drift: 0.03(1min)%FS
    • Temp. Effect on Zero: 10 1Zero %FS/
    • Temp. Effect on Output: 0.05%FS/10
    • Zero Output: 0.1mV/V
    • Input Resistance: 1000 20
    • Output Resistance: 1000 20
    • Insulation Resistance: 5000M
    • Excitation Voltage: 10V
    • Operation Temp. Range: 0+50
    • Overload Capacity: 150%FS
  • -20%

    DHT11 Humidity & Temperature Sensor

    Sensors
    (0)
    Original price was: ₨350.00.Current price is: ₨280.00. Quick View
    • Dimension 28mm*12mm*10mm
    • Main chip DHT11 huminity sensor
    • Voltage: DC 5V
    • Digital output
    • Humidity Range: 2090%RH
    • Humidity accuracy:5%RH
    • Temperature range:0-60
    • Temperature accuracy: 2
  • -46%
    Out Of Stock

    IR Obstacle Avoidance Sensor

    IR & Vision
    (0)
    Original price was: ₨250.00.Current price is: ₨135.00. Quick View
    • There is an obstacle, the green indicator light on the circuit board
    • Detection distance: 2 ~ 30cm
    • Detection angle: 35
    • Comparator chip: LM393
    • 3mm screw holes for easy mounting
  • -17%

    Flex Sensor 2.2 Inch

    Flex & Force
    (0)
    Original price was: ₨3,600.00.Current price is: ₨2,999.00. Quick View
    • Angle Displacement Measurement
    • Bends and Flexes physically with motion device
    • Possible Uses
    • Simple Construction
    • Low Profile
    • Physical Therapy
    • Musical Instruments
    • Computer Peripherals
    • Medical Devices
    • Gaming (Virtual Motion)
    • Robotics
  • -15%

    Force Sensitive Resistor 0.5 INCH FSR

    Flex & Force
    (0)
    Original price was: ₨1,350.00.Current price is: ₨1,150.00. Quick View
    • Detection area (detection range): 14.5 mm circle
    • Physical Diameter: 18.3mm circle
    • The output signal (output signal): Passive variable to hold
    • The Force-sensitive range (range), pressure test: 100g to 10 kg
    • Lifespan (life):> 10 m letter actuation

    Dimensions:

    • Total length: 56mm
    • Overall width: 18.3mm
    • Diameter detection: 14.5mm
    • Thickness: 0.4mm
  • -28%

    MQ135 Air Quality Detector Sensor Module

    Gas Sensor
    (0)
    Original price was: ₨540.00.Current price is: ₨389.00. Quick View
    1. Air Quality Sensor Module
    2. Condition: New
    3. Size: 32mm X22mm X27mm
    4. Main chip: MQ-135
    5. Operating Voltage: 5V DC
    6. Type: Analog & Digital
    7. Sensitivity to Ammonia, Sulphide and Benzene steam
    8. Detecting Range: 100-1000ppm
    9. With signal output instructions
    10. TTL output signal is low level
    11. Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
    12. Color is showing pictures.
    13. Sensitive for benzene, alcohol, smoke
    14. Fast response and recovery
    15. Adjustable sensitivity
    16. Signal output indicator
    17. Output voltage boosts along with the concentration of the measured gases increases
  • -41%

    GY-291 ADXL345 3-Axis Accelerometer Module

    Accelero, Gyro. IMU, Magneto
    (0)
    Original price was: ₨590.00.Current price is: ₨349.00. Quick View
    • Main Chip: ADXL345
    • Model: GY-291
    • Power Supply: 3-5V
    • Means of Communication: IIC / SPI Communication Protocol
    • Measuring Range: ±2g /±16g
    • Digital-Output Triple-Axis Accelerometer with a Programmable Full-Scale Range of ±2g, ±4g, ±8g and ±16g and Integrated 16-bit ADCs
    • Accelerometer Normal Operating Current: 450µA
    • Ultralow Power: as low as 23 μA in Measurement Mode and 0.1 μA in Standby Mode at VS = 2.5 V (typical)
    • Sleep Mode Current: 8µA
    • Communication: SPI (3- and 4-wire) and I2C Digital Interfaces
    • User-Programmable Interrupts
    • Wake-On-Motion Interrupt for Low Power Operation of Applications Processor
  • -20%

    GY-273 Magneto HMC5883L

    Accelero, Gyro. IMU, Magneto
    (0)
    Original price was: ₨750.00.Current price is: ₨599.00. Quick View
    1. Supply Voltage VCC: 3.3 to 6 V
    2. Heading Accuracy: 1 to 2
    3. Magnetic Field Range: -8 to +8 Gauss
    4. I2C Address: 0x1E (7-bit address)
    5. Max Data Rate: 160 Hz
    6. Digital Voltage Level: 3.3V
    7. Dimensions (excluding pins): 18.2mm (0.717) x 13.3mm (0.524) x 2.2mm (0.087)
    8. Weight: 0.95g (0.034oz)
  • -10%
    Out Of Stock

    GPS Arduino Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨5,350.00.Current price is: ₨4,799.00. Quick View

    This is a GPS module breakout board with SD storage based on the u-blox NEO-6M GPS and its foot print is compatible with arduino boards . This board features an SD card socket, which makes it convenient for building data loggers.

  • -14%

    W5100 Ethernet Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨3,500.00.Current price is: ₨2,999.00. Quick View
    • Operating voltage 5V (supplied from the Arduino Board)
    • Ethernet Controller: W5100 with internal 16K buffer
    • Connection speed: 10/100Mb
    • Connection with Arduino on SPI port
    • The Shield contains a number of informational LEDs
    • PWR: indicates that the board and shield are powered
    • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
    • FULLD: indicates that the network connection is full duplex
    • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
    • RX: flashes when the shield receives data
    • TX: flashes when the shield sends data
    • TX: flashes when the shield sends data
    • COLL: flashes when network collisions are detected
  • Out Of Stock

    Arduino WiFi Shield CC3000

    Arduino & IOT Boards
    (0)
    ₨2,800.00 Quick View
    1. Based on TI CC3000 WIFI module.
    2. Use SPI communication .
    3. Integrated 3.3V regulator .
    4. Level shifter integrated .
    5. Integrated ceramic antenna .
    6. It has a connector for external antenna WIFI
    7. Compatible with Arduino UNO, Mega, Leondardo & Micro
    8. Antenna: Onboard Ceramic
    9. MicroSD card slot onboard
    10. Reset button
    11. Communication Protocol: SPI
    12. Connects via IEEE 802.11 b/g networks
    13. Tx Bandwidth: 11Mbps
    14. Tx Sensitivity: +/-18dBm
    15. Rx sensitivity: -86dBm
    16. IRQ pin for interrupts (useful for asynchronous connections)
    17. Supports WEP, WPA, WPA2, TKIP and AES
    18. TCP and UDP Client & Server Modes available
    19. Max Concurrent TCP/UDP Sockets: 4
    20. TCP/IP stack is built in.