-
- Voltage: 3.3V to 5V
- Characteristics: 700nm x 1mm
- Chipset: TSOP1838 37.9kHz
- Daylight Rejection: up to 500LUX
- Receiving Distance: up to 18 m
- Size: 19mm x 15mm x 14mm
-
Temperature Sensor Module DS18B20
Original price was: ₨290.00.₨279.00Current price is: ₨279.00. Quick View- Digital signal output
- 18B20 Temperature Sensor Chip
- Resolution adjustment ranges from 9-12 bytes.
- Send data via a pin
- Temperature measurement ranges: -55C to +125C, be accurate to 0.5C.
-
- Working voltage: 5V
- Pulses per 360-degree revolution: 20
- Push button shaft On/Off switch
- Threaded shaft for panel mounting, also 2 mounting screw holes on the circuit board
- Standard “D” shaft, you can purchase knobs to give it a finished look
-
- Dimensions: 40 x 15 x 7 mm(LxWxH).
- Weight: 3 gm.
- Using SW-420 normally closed type vibration sensor
- Comparator output, clean signal, good waveform, strong driving ability, >15mA
- Operating voltage 3.3V ~ 5V
- Output format: digital switching output (0 and 1)
- Using a wide voltage LM393 comparator
- With bolt holes for easy installation
-
- Model: YF-S201
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Liters/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Liter: 450
- Durability: minimum 300,000 cycles
- Cable length: 15cm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 2.5″ x 1.4″ x 1.4″
-
- The real-time clock counts minutes, seconds, date, hours, month day of the week, year and leap-year compensation upto 2100.
- 318 temporary data storage RAM
- Working current of 2.0V, less than 300nA
- Read / Write clock or RAM data with two kinds of mode of single-byte transfer mode and multi-byte character set
- 8 pin DIP package or optional 8 pin SOIC package based on the surface assembly
- Simple 3 wire interface
- Compatible with TTL Vcc=5V
- Double power supply pipe for main power and backup power supply.
-
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -20A~ 20A
- Sensitivity: 100mV/A
- The current sensor chips: ACS712_ELC-20A.
- Pin 5V power supply, onboard power indicator.
- There is no the detection current through, the output voltage is VCC / 2.
- The module can be measure plus or minus 20 amps, corresponding to the analog output of 185 mV / A.
-
Soil Moisture Sensor For Arduino
Original price was: ₨350.00.₨179.00Current price is: ₨179.00. Quick View- Easy-to-use
- 3-pin screw pin terminal is pre-soldered to the board
- PCB coated in gold finishing
- 3.3V to 5V operating supply voltage range
-
- Local sensor accuracy (Max) (+/- C): 0.5
- Operating temperature range (C): -40 to 110,-55 to 150,0 to 100,0 to 70
- Supply voltage (Min) (V): 4
- Supply voltage (Max) (V): 30
- Supply current (Max) (uA): 14
- Sensor gain (mV/Deg C): 10
- Rating: Catalog
- Features: UL Recognized
- Interface: Analog Output
-
NRF24L01 2.4GHz Wireless Transceiver Module
Original price was: ₨650.00.₨249.00Current price is: ₨249.00. Quick View- Worldwide 2.4GHz ISM band operation Free license to use.
- 126 RF channels.
- High air data rate: 250kbps, 1 and 2Mbps.
- Transmitter: 11.3mA at 0dBm output power.
- Receiver: Fast AGC for improved dynamic range.
- Receiver: Integrated channel filters.
- Enhanced ShockBurst:1 to 32 bytes dynamic payload length,6 data pipe MultiCeiver for 1:6 star networks.
- Host Interface:4-pin hardware SPI,3 separate 32 bytes TX and RX FIFOs.
- Low Power Management:1.9 to 3.6V supply range.
- GFSK modulation.
- Auto packet transaction handling.
- Easy to design.
- Small size:15mm*29mm.
-
Heart Rate Monitor ECG AD8232 Module + Leads
Original price was: ₨2,500.00.₨1,479.00Current price is: ₨1,479.00. Quick View- Supply voltage: DC 3.3V
- Output: Analog output
- Interface (connected to RA LA RL): 3PIN 2.54 pin or headset
- Size 36mm * 31mm * 18mm
- Operating temperature: -40C +85 C
-
Microphone Amplifier – MAX9814 w/ Auto Gain Control
Original price was: ₨800.00.₨449.00Current price is: ₨449.00. Quick View- The default ‘max gain’ is 60dB, but can be set to 40dB or 50dB by jumpering the Gain pin to VCC or ground.
- You can change the Attack/Release ratio, from the default 1:4000 to 1:2000 or 1:500.
- The ouput from the amp is about 2Vpp max on a 1.25V DC bias, so it can be easily used with any Analog/Digital converter that is up to 3.3V input. If you want to pipe it into a Line Input, just use a 1uF blocking capacitor in series.
-
MQ7 MQ-7 Gas Sensor Detection Module
Original price was: ₨450.00.₨399.00Current price is: ₨399.00. Quick View- Product Name: Gas Sensor Module;
- Model: MQ-7;
- Type: Analog
- Detecting Type : Carbonic Oxide(Co);
- Rated Voltage: DC 5V;
- Rated Current: 180mA
- Detecting Range: 100-1000ppm;
- Pin Quantity: 4;
- Pin Spacing: 1.8mm/ 0.07″
- Pin Definition: AO-analog Output, DO-Digital Output, GND- Ground, VCC-Voltage To Current Converter ;
- Total Size: 35 x 20 x 21mm/ 1.4″ x 0.79″ x 0.83″ (L*W*H)
-
IR Obstacle Avoidance Sensor
Original price was: ₨250.00.₨135.00Current price is: ₨135.00. Quick View- There is an obstacle, the green indicator light on the circuit board
- Detection distance: 2 ~ 30cm
- Detection angle: 35
- Comparator chip: LM393
- 3mm screw holes for easy mounting
-
- Supply Voltage VCC: 3.3 to 6 V
- Heading Accuracy: 1 to 2
- Magnetic Field Range: -8 to +8 Gauss
- I2C Address: 0x1E (7-bit address)
- Max Data Rate: 160 Hz
- Digital Voltage Level: 3.3V
- Dimensions (excluding pins): 18.2mm (0.717) x 13.3mm (0.524) x 2.2mm (0.087)
- Weight: 0.95g (0.034oz)
-
he Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
PZEM-022 Open and Close CT 100A AC Digital Display Power Monitor Meter
Original price was: ₨5,000.00.₨2,999.00Current price is: ₨2,999.00. Quick View-
Operating Voltage: 80–260V AC
-
Measurement Current Range: 0.02–100A
-
Power Range: 0.5W–22,000W
-
Energy Range: 0–999kWh
-
Frequency Range: 45–65Hz
-
Power Factor Range: 0.00–1.00
-
Measurement Accuracy: Class 1.0
-
Nominal Power: 100A / 22000W
-
-
FSR402 Force Sensitive Resistor FSR
Original price was: ₨1,500.00.₨729.00Current price is: ₨729.00. Quick ViewThe FSR is made of 2 layers separated by a spacer. The more one presses, the more of those Active Element dots touch the semiconductor and that makes the resistance go down. FSRs are basically a resistor that changes its resistive value (in ohms Ω) depending on how much it is pressed. These sensors are fairly low cost, and easy to use but they’re rarely accurate. They also vary some from the sensor to sensor perhaps 10%. So basically when you use FSRs you should only expect to get ranges of response. While FSRs can detect weight, they’re a bad choice for detecting exactly how many pounds of weight are on them. However, for most touch-sensitive applications like “has this been squeezed or pushed and about how much” they’re a good deal for the money!
-
MQ-4 Methane/ Natural Gas Sensor Module for Arduino
Original price was: ₨549.00.₨329.00Current price is: ₨329.00. Quick View- Model : MQ4 Gas Sensor Module
- IC Chip: LM393
- Operating Voltage: 3 ~ 5V (DC)
- Detecting Range: 300ppm to 10000ppm
- Dimensions: 3.1 x 1.9 x 2.1 cms
- Weight: 5 grams
-
TTP223B Blue Touch Sensor 1-Ch-Capacitive Touch Sensor
Original price was: ₨250.00.₨95.00Current price is: ₨95.00. Quick View- Power supply voltage(VCC): 2.0, 3, 5.5 V.
- Output high VOH: 0.8VCC V
- Output low VOL: 0.3VCC V
- Response time (touch mode) : 60 mS
- Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V) : 8 mA
- Output pin pull-up current (@ VCC = 3V, VOH = 2.4V) : 4 mA
- Response time (low power mode) : 220 mS
- Size : 24 x 24 x 7.2 mm
-
SCT013-000 CT 100A Non-invasive AC Current Sensor
Original price was: ₨1,800.00.₨1,249.00Current price is: ₨1,249.00. Quick View- Core Material: Ferrite
- External Material : ABS
- Input Current : 100A
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Working Temperature -25-70°C
- Cable Length : Approx. 1.18m/ 45.4″
- Total Size : Approx. 60 x 30 x 20 mm.
-
50A SCT-013-000 Non-invasive AC Current Clamp Sensor
Original price was: ₨1,800.00.₨1,249.00Current price is: ₨1,249.00. Quick View- Input Current: 0~50A AC
- Output Mode: DC 0~1V
- Non-linearity:2-3%
- Build-in sampling resistance(RL): 62Ω
- Turn Ratio: 1800:1
- Resistance Grade: Grade B
- Work Temperature: -25°C ~ ﹢70°C
- Dielectric Strength(between shell and output): 1000V AC/1min 5mA
- Leading Wire in Length: 1m
- Open Size: 13mm x 13mm
-
10A/1A Induction current sensor SCT-013-010 (1V)
Original price was: ₨1,800.00.₨1,249.00Current price is: ₨1,249.00. Quick View- Current measurement range: 0 ÷ 10 A AC
- Maximum diameter of the measuring cable: fi 12 mm
- Built -in burdening resistor: Yes
- Output voltage: 0 ÷ 1 V AC
- cable length: 1 m
- mass: 50 g
-
HC-12 HC12 Si4463 433MHZ RF Wireless Serial Module With Antenna
Original price was: ₨1,350.00.₨749.00Current price is: ₨749.00. Quick View- Working frequency: 433.4MHz to 473.0MHz
- Supply voltage: 3.2V to 5.5VDC
- Communication distance: 1,000m in the open space
- Serial baud rate: 1.2Kbps to 115.2Kbps(default 9.6Kbps)
- Receiving sensitivity: -117dBm to -100dBm
- Transmit power: -1dBm to 20dBm
- Interface protocol: UART/TTL
- Operating temperature: -40℃ to +85℃
- Dimensions: 27.8mm x 14.4mm x 4mm
-
Laser Diode Module 650nm 5v Laser Light Module Ky008
Original price was: ₨180.00.₨99.00Current price is: ₨99.00. Quick View- Voltage: 3.0 V – 5 V.
- Output: red laser straightly(650nm).
- Driver: APC circuit.
- Size: Φ 12.0 x35mm.
- Line length: about 135 mm.
- Transmit power: 58mW.
- Operating Current: 40mA.
- Operating temperature: -36 ~ 65◦C.
- Pot size: 15 meters spot for φ10 mm ~ φ15.
- Outer diameter: 6 mm.
-
HX711 Module Load Cell Voltage Amplifier
Original price was: ₨160.00.₨149.00Current price is: ₨149.00. Quick ViewThe HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor Load Cell Amplifier and ADC Module is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the module to your microcontroller you will be able to read the changes in the resistance of the load cell with some calibration. You?ll be able to get very accurate weight measurements.
-
Arduino MEGA 2560 PRO Mini
Original price was: ₨4,500.00.₨2,999.00Current price is: ₨2,999.00. Quick View- Microcontroller ATmega2560
- USB-TTL converter: CH340
- Power Out:5V-800mA
- Power IN.: 5V
- Power IN. VIN/DC Jack:5V
- Power Consumption: 5V 220mA
- Logic Level: 5V
- USB: Micro USB
- Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O: 54
- Analog I/O: 16
- Memory Size: 256kb
- Data RAM Type/Size: 8Kb
- Data ROM Type/Size: 4Kb
- Interface Type : ISP
- Operating temperature 40C/+85C
- Length x Width:38mmx54mm
-
UGN3503 AH3503 Hall Effect Sensor
Original price was: ₨200.00.₨159.00Current price is: ₨159.00. Quick View- Extremely Sensitive
- Flat Response to 23 kHz
- Low-Noise Output
- 4.5 V to 6 V Operation
-
Arduino Due AT91SAM3X8E ARM Cortex-M3 Board
Original price was: ₨6,000.00.₨4,500.00Current price is: ₨4,500.00. Quick View- MicrocontrollerAT91SAM3X8E
- Operating Voltage3.3V
- Input Voltage (recommended)7-12V
- Input Voltage (limits)6-16V
- Digital I/O Pins54 (of which 12 provide PWM output)
- Analog Input Pins12
- Analog Output Pins2 (DAC)
- Total DC Output Current on all I/O lines130 mA
- DC Current for 3.3V Pin800 mA
- DC Current for 5V Pin800 mA
- Flash Memory512 KB is all available for the user applications
- SRAM96 KB (two banks: 64KB and 32KB)Clock Speed84 MHz
- Length101.52 mm
- Width53.3 mm
- Weight36 g
-
PWM DC Motor Speed Controller 8A With Display
Original price was: ₨1,500.00.₨1,099.00Current price is: ₨1,099.00. Quick View- Suitable for motors with voltage: 12 and 24V
- The total range of permissible tension: 6V to 30V DC
- Output current: Rated current 5A (8A max short term)
- PWM frequency: 16 kHz
- Adjustable PWM duty cycle : 0% -100%
- LED Digital display showing the duty cycle
- The dimensions of the regulator are 7.8 x 4.2 x 2.5 cm
-
TTP224 4 Way Capacitive Touch Switch
Original price was: ₨599.00.₨199.00Current price is: ₨199.00. Quick View- Onboard TTP224 capacitive touch sensor IC 4 keys.
- 4 board-level status indicators.
- Input Operating voltage: DC 2.0V – 5.5V
- The module can set the output mode, the key output mode, the maximum output time, and fast/low power selection.
- Input with reverse polarity protection.
- LED Color: connected to Output pin
- Idle current: <10uA
-
Piezoelectric Shock Tap Sensor Vibration Switch Module
Original price was: ₨899.00.₨715.00Current price is: ₨715.00. Quick View- Item Name: Piezoelectric Shock Tap Sensor Vibration Switch Module
- Item Type: Vibration Switch Sensor Module
- Working Voltage: 5.0V (DC)
- Interface Type: AD/DO
- AO: Analog Signal Output
- DO: TTL Level Output
- Working Temperature: -10 C ~ +70 C
- Size: Approx. 20 x 20mm / 0.8 x 0.8in
- Weight: 4.5 g / 0.2 oz(approx.)
- Test Method and Wiring:
- G (GND):: Power ground
- V (VCC): Operating voltage 5V (DC)
- ADO: Analog signal output
- According to the vibration intension, the higher the output voltage, the higher the vibration amplitude sensitivity can be adjusted by the potentiometer (the left turn sensitivity is low, the right turn sensitivity is high). The high sensitivity output can be adjusted to respond with a mouth blow or a tap with a hand.
- DO: TTL level output. Output signal LED indication. TTL output valid signal is high level, output control power
-
PR12 4DP Proximity sensor Autonics
Original price was: ₨999.00.₨799.00Current price is: ₨799.00. Quick ViewSensing distance
1.5mmInstallation
Shield(flush)Standard sensing target
8×8×1mm(iron)Response frequency
1.5kHzCurrent specification
Current consumption: Max. 10mAControl output
PNP Normally OpenMaterial
Brass(nickel plated)Cable Standard/material
Standard cableBody length
Standard typeWeight
Approx. 64g (approx. 52g) -
PR08-2DP Inductive Proximity Sensor
Original price was: ₨999.00.₨769.00Current price is: ₨769.00. Quick View- Wire type and power
- DC 3-wire type 12-24VDC Sensing side diameter
- M08Sensing distance 2mm
- Installation Non-shield(non-flush)
- Standard sensing target8x8x1mm(iron)
- Response frequency1kHzCurrent specification
- Current consumption: Max. 10mA
- Control output PNP Normally Open Material Brass(nickel plated)
- Cable Standard/material Standard cable
- Protection structureIP67
- Approval Body length Standard type
- Environment Ambient temperature-25 to 70C, storage: -30 to 80C
- Environment Ambient humidity35 to 95% RH, storage: 35 to 95% RH
- Hysteresis(distance)Max. 10% of sensing distance
- Residual voltage Max. 2V
- Weight Approx. 64g(approx. 52g)
-
MAX30100 Pulse Oximeter Heart Rate Sensor
Original price was: ₨550.00.₨359.00Current price is: ₨359.00. Quick View- 1.8V – 5.5V is its operating voltage.
- I2C is Its interface type.
- 18.8 x 14.4 3 mm is the dimensions of the Heart sensor module.
- Heart Sensor weight is 1.2g.
- The heart sensor module brand is MAX30100.
- The Digital is its Output type.
- The working principle of this sensor is the Biosensor.
- This is a pressure-sensitive and force-sensitive sensor.
- The polymer is its material texture.
-
SPO2 MAX30102 Blood Oxygen Concentration Sensor
Original price was: ₨1,200.00.₨499.00Current price is: ₨499.00. Quick View- Tiny 12.7mm x 12.7mm (0.5in x 0.5in) Board Size
- Free Algorithm
- Highly integrated, small-size sensor
- Non-chest based heart-rate/SpO2 detection
- Ultra-low power consumption
-
125KHz EM18 reader module EM-18 build in coil antenna
Original price was: ₨2,150.00.₨1,499.00Current price is: ₨1,499.00. Quick View- Operating voltage of EM-18: +4.5V to +5.5V
- Current consumption:50mA
- Can operate on LOW power
- Operating temperature: 0C to +80C
- Operating frequency:125KHz
- Communication parameter:9600bps
- Reading distance: 10cm, depending on TAG
- Integrated Antenna
-
Pack of 5 27mm Piezo Electric Plate
Original price was: ₨400.00.₨330.00Current price is: ₨330.00. Quick View- Product type: Piezoelectric Transducer Piezo Sensor
- Colour: copper and silver
- Dimension: 27 mm
- Weight: 2 g
- Sheet material: bronze
- Package contains: 1 x piezoelectric sensor
-
Interfacing EMG Muscular Signal Sensor
Original price was: ₨6,000.00.₨4,499.00Current price is: ₨4,499.00. Quick ViewFeatures:
- Small Form Factor
- Specially Designed for Microcontrollers
- Adjustable Gain using onboard potentiometer
- 5mm Connector
Applications:
- Video games
- Robotics
- Medical equipment
-
37 in 1 Sensor Module Board Set Kit For Arduino Card Board Box
Original price was: ₨3,000.00.₨2,599.00Current price is: ₨2,599.00. Quick ViewThis 37 In 1 Sensor Module Kit for Arduino is supplied with a variety of sensors that are compatible with Arduino Boards. This is the most complete performance starter kit with all the essential Arduino sensors.
It comprises 37 Pcs essential Arduino components. The kit includes the latest Arduino components that can be used to turn your idea into a real product.
Tons of updated lessons and Arduino codes are available on Google and YouTube for free. It is extremely easy for Arduino fancier to control and use these modules. This kit will help you control the physical world with sensors.
-
CJMCU-4051 74HC4051 8 Channel Analog Multiplexer Module
Original price was: ₨520.00.₨480.00Current price is: ₨480.00. Quick View- Wide analog input voltage range from -5 V to +5 V
- Complies with JEDEC standard no. 7A
- Low ON resistance:
- 80 ohm(typical) at VCC -VEE = 4.5 V
- 70 ohm(typical) at VCC -VEE = 6.0 V
- 60 ohm(typical) at VCC -VEE = 9.0 V
- Logic level translation: to enable 5 V logic to communicate with 5 V analog signals
- Typical break before make built-in
- ESD protection:
- HBM JESD22-A114F exceeds 2000 V
- MM JESD22-A115-A exceeds 200 V
- CDM JESD22-C101E exceeds 1000 V
- Multiple package options
- Specified from -40 to +85 and -40 to +125
-
ESP8266 Witty Cloud ESP-12F WiFi Module
Original price was: ₨1,099.00.₨899.00Current price is: ₨899.00. Quick View- LDR Light Sensor on board.
- WS2812 Led on board.
- Includes CH340G USB-to-UART programmer.
- Includes LDR (light dependent resistor a.k.a photoresistor) connected to ESP’s ADC pin.
- Supports 3 modes: AP, STA, AP+STA.
- Dimensions: 24mm x 16mm.
- Micro USB connection for power and/or programming
-
RPM Measurement Sensor Rotational Speed Measuring Module
Original price was: ₨160.00.₨119.00Current price is: ₨119.00. Quick View- Input voltage: 3.3V to 5V
- Output signal: TTL signal, active low
- Pulse frequency range: 0 to 100Hz
- RPM range: 0 to 6000RPM
- Dimensions: 32 x 14 x 7mm
- Weight: 5g
-
Hot End For 3D Printer
Original price was: ₨3,000.00.₨1,699.00Current price is: ₨1,699.00. Quick View- Model: J-Head Hot End V6
- Design: Long-Distance
- Improved processing of flexible filament
- More compact design
- Easier maintenance
- Reduced heating
- Improved temperature control and cooling
- Material: aluminum
- Nozzle: 0.4 mm
- Filament: 1.75 mm
- 12V 40W heating cartridge
- NTC thermistor 100k
- Cable length: approx. 90 cm
-
Ph Sensor Gravity Sensor Module
Original price was: ₨7,800.00.₨5,999.00Current price is: ₨5,999.00. Quick View- Module Power: 5.00V
- Module Size : 43 x 32mm(1.69×1.26″)
- Measuring Range :0 – 14PH
- Measuring Temperature: 0 – 60 ℃
- Accuracy : ± 0.1pH (25 ℃)
- Response Time: ≤ 1min
- pH Sensor with BNC Connector
- pH2.0 Interface ( 3 foot patch )
- Gain Adjustment Potentiometer
- Power Indicator LED
-
-
Photoelectric Sensor G183A10 NA
Original price was: ₨1,800.00.₨1,440.00Current price is: ₨1,440.00. Quick ViewPhotoelectric sensors are electronic devices capable of detecting the approximation, passage and presence of metallic materials or not, through emission and reception of infrared light provided they are located within the distance of actuation of the sensor. The detection of the photoelectric sensor occurs without physical contact between the sensor and the trigger because it has no moving parts subject to mechanical wear and thus increase the life of the equipment. The Photoelectric Sensor price base on the three operating principles Diffuse, Retroreflective, Barrier. Photoelectric sensor price model G18 with plastic housing has tubular shape with 18mm diameter (M18) with cable type or connector depending on type (diffuse, reflective or barrier) has sensing distances of 10, 30 cm, 2 and 5 m. Photoelectric sensor price has electrical configuration type NPN or PNP contacts normally open (NA), normally closed (NF) or (NA + NF) and connection with 2 or 4 pins.
-
- Very low supply current
- Photodetector and preamplifier in one package
- Internal filter for PCM frequency
- Improved shielding against EMI
- Supply voltage: 2.5 V to 5.5 V
- Improved immunity against ambient light
- Insensitive to supply voltage ripple and noise