-
Microphone Sound Sensor Module
Original price was: ₨199.00.₨149.00Current price is: ₨149.00. Quick ViewThis module allows you to detect when sound has exceeded a set point you select. Sound is detected via a microphone and fed into an LM393 op amp. The sound level set point is adjusted via an on board potentiometer. When the sound level exceeds the set point, an LED on the module is illuminated and the output is sent low. It has working voltage of 3.3-5V.
-
NODEMCU LUA WIFI BOARD BASED ON ESP8266 CP2102 MODULE
Original price was: ₨1,099.00.₨669.00Current price is: ₨669.00. Quick View- Wi-Fi Module The ESP-12E module is similar to the ESP-12 module but with 6 extra GPIOs.
- USB micro USB port for power, programming, and debugging
- Headers 2x 2.54mm 15-pin header with access to GPIOs, SPI, UART, ADC, and power pins
- Misc Reset and Flash buttons
- Power 5V via micro USB port
- Dimensions 49 x 24.5 x 13mm
-
ESP8266 ESP12E -NODEMCU – CH340
Original price was: ₨799.00.₨559.00Current price is: ₨559.00. Quick View- Input Voltage: 2.5 ~ 3.6V
- Operating Voltage: 3.3V
- CPU: 32-bit RISC Tensilica Xtensa LX106 running at 80 MHz
- 64 KB of instruction RAM, 96 KB of data RAM (80x Arduino UNO!)
- 512 KB of EEPROM (512x Arduino UNO!)
- External QSPI flash – 512 KB to 4 MB* (up to 16 MB is supported)
- IEEE 802.11 b/g/n Wi-Fi
- Integrated TR switch, balun, LNA, power amplifier and matching network
- WEP or WPA/WPA2 authentication, or open networks
- Digital I/O Pins (DIO): 16
- Analog Input Pins (ADC): 1
- UARTs: 1 on dedicated pins, plus a transmit-only UART can be enabled on GPIO2
- SPIs: 1
- I2Cs: 1
- Flash Memory: 4 MB
- SRAM: 64 KB
- Clock Speed: 80 Mhz
- 80 Mhz clock (5x arduino UNO or mega!)
-
- Model: YS-S401
- Working Voltage: DC 5V~24V
- Maximum Working Current: 15mA @ 5V DC
- Flow Rate Range: 0.3~6L/min
- Connection: 6mm (external diameter)
- Inlet Water Pipe Diameter: 2.5-4mm
- Load Capacity: 10mA (DC 5V)
- Operating Temperature: 80
- Liquid Temperature: 120
- Operating Humidity: 35%-90%RH
- Water Pressure: 2.0MPa
- Storage Temperature: -25 to + 80
- Storage Humidity: 25%-95%RH
-
- Digital Output Hall-effect sensor.
- Operating voltage: typically 5V.
- Output Current: 25mA.
- It can be used to detect both the poles of a magnet.
- The output voltage is equal to the operating voltage.
- Operating temperature: -40C to 85C.
- Turn on and Turn off time is 2 sec each.
- Inbuilt reverse polarity protection.
- Suitable for Automotive and Industrial Applications.
-
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC,parity,bit coding bit counting
- Anticollision
- Typical tickting transaction: <100 ms ( including backup management)
-
The ProtoShield makes it easy for you to design custom circuits. You can easily solder TH or SMD ICs on the prototyping area to test them with your Arduino board. The SMD area is designed for a maximum of 24 pins SOIC integrated circuit and the TH area contains a lot of space for the needed components around your project. You can even stick a mini breadboard (not included) on the protoarea for solderless operation. The proto area includes also two power lines (IOREF and GND), two LEDs pads and SPI signals breakout pads for boards with SPI only on the ICSP header like Zero.
-
- Supply Voltage : 12 V
- Fused at 5A for additional safety and component protection
- Heated bed control with additional 11A fuse
- Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
- I2C and SPI pins left available for future expansion.
- 2 stepper motor for Z axis in parallel.
-
- It has a nice standard 0.1×0.1 prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- A IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- A surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out!
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
- It has a nice standard 0.1×0.1 prototyping grid with big pads
-
GY-31 TCS230 TCS3200 Color Sensor
Original price was: ₨2,000.00.₨1,350.00Current price is: ₨1,350.00. Quick View- High-resolution conversion of light intensity to frequency.
- Chip pins all has drawn for standard 100.
- Put the needle (2.54 mm).
- Mil-convenient for bitmap board.
- Programmable color and full-scale output frequency.
- Communicate directly with a microcontroller.
- Low-profile surface mount package.
-
- Imported chips TCS3200 PCB board with gold plating.
- TCS3200 is TCS230 upgrade version, the better.
- Power supply: 3-5v
- Anti-light interference.
- White LED, can control the on and off.
- Can detect non-luminous object color.
- PCB dimensions: (L) 33mm * (W) 25mm
-
- Seamless Integration with other components
- Made of superior grade material for long life
- Designed to contribute in the overall performance of the equipment
- Lightweight and durable, easy to match the ultrasonic sensor
-
This is NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub 26A power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01 provides a true ULP solution enabling months to years of battery life when running on coin cells or AA/AAA batteries. These RF modules are very popular among the Arduino tinkerers. The nRF24L01 is used on a wide variety of applications that require wireless control. They are transceivers which this means that each module can transmit and receive data.
-
- Power Supply : 5V DC
- Quiescent Current : <2mA
- Working Currnt: 15mA
- Effectual Angle: <15
- Ranging Distance : 2cm 400 cm/1x13ft
- Resolution : 0.3 cm
- Measuring Angle: 30 degree
- Trigger Input Pulse width: 10uS minimum
- Dimension: 45mm x 20mm x 15mm
-
Hall effect sensor is transducing devices used to detect and generate a voltage when in the presence of a magnetic field. They are designed to induce a voltage as an output when a magnetic field is present at its input. The output voltage can be variable depending on the magnitude of the magnetic field. Hall effect sensors, as they name states are effect sensors, which can be used to sense different categories, like speed, position of objects, rotational speed or frequency and be used as a fault detector. They can be used to detect a time-varying current, as time-varying current produce magnetic fields, which can then be sensed by the Hall effect transducer and produce a voltage with some proportion the amount of magnetic field present at the sensor.
-
- Voltage: 3.3V to 5V
- Characteristics: 700nm x 1mm
- Chipset: TSOP1838 37.9kHz
- Daylight Rejection: up to 500LUX
- Receiving Distance: up to 18 m
- Size: 19mm x 15mm x 14mm
-
Temperature Sensor Module DS18B20
Original price was: ₨290.00.₨279.00Current price is: ₨279.00. Quick View- Digital signal output
- 18B20 Temperature Sensor Chip
- Resolution adjustment ranges from 9-12 bytes.
- Send data via a pin
- Temperature measurement ranges: -55C to +125C, be accurate to 0.5C.
-
MT3608 Step-Up Adjustable DC-DC Switching Boost Converter
Original price was: ₨160.00.₨109.00Current price is: ₨109.00. Quick View- Input Voltage: 2-24V DC
- Output Voltage: 5-28V DC
- Maximum Output Current: 2A
- Switching Frequency: 1.2Mhz
- Output Ripple: <100mV
- Module Size: 37.2mm x 17.2mm x 14.0mm
- About 93% Efficiency
- Features like an under-voltage lockout, thermal overload protection
-
The logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. A Logic Level Converter is very easy to connect and use since it doesn’t need any programming, all you have to do is connect the 5V wire on one side and the 3.3V on the other.
-
- Core Material: Ferrite
- External Material : ABS
- Input Current : 30A
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Working Temperature -25-70°C
- Cable Length : Approx. 1.18m/ 45.4″
- Total Size : Approx. 60 x 30 x 20 mm.
-
LM35 Temperature Sensor Module
Original price was: ₨300.00.₨275.00Current price is: ₨275.00. Quick View- Calibrated directly in Degree Celsius
- Linear + 10.0 mV/C scale factor
- 0.5C accuracy guarantee-able (at +25C)
- Rated for full 55 to +150C range
- Operates from 4 to 30 volts
- Less than 60mA current drain
- Low self-heating, 0.08C in still air
-
- Rated Load: 10Kg
- Rated Output: 1.0 ±0.15mV/V
- Zero Output: ±0.1mV/V
- Cree: 0.03%F.S./30min
- Input End: Red+, Black-
- Output End: Green+, White-
- Input Impedance: 1115±10% Ω
- Output Impedance: 1000±10% Ω
- Maximum working voltage: 15V DC
- Operating temperature range: -20~60°C
- Total Size: 80 x 13 x 13mm/3.14 x 0.51 x 0.51″(L X W X H)
-
Arduino SD Card Reader Module
Original price was: ₨220.00.₨199.00Current price is: ₨199.00. Quick View- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V\
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
-
GPS Neo 6m U-Blox NEO-6M GPS Module
Original price was: ₨1,999.00.₨899.00Current price is: ₨899.00. Quick View- 5Hz position update rate
- Operating temperature range: -40 TO 85C UART TTL socket
- EEPROM to save configuration settings
- Rechargeable battery for Backup
- The cold start time of 38 s and Hot start time of 1 s
- Supply voltage: 3.3 V
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
- Separate GPS antenna
-
PPM encoder is the role of the receiver output of multiple channel PWM signal encoded into PPM composite signal output, single-wire connection to support the flight control.
-
IR Proximity Sensor 0A4-1SK
Original price was: ₨950.00.₨900.00Current price is: ₨900.00. Quick View- Type of sensor: photoelectric
- Range : 40~300mm(1.5 to 12)
- Output configuration: Analogue voltage
- Operation mode: Diffuse-reflective
- Supply voltage: -0.3~7V DC
- Connection: S3B-PH
- Max operating current: 22mA
- Average current consumption: 12 mA
- Output voltage differential over distance range: 2.3 V (typical)
- Update period: 16.5 4 ms
- Size: 44.5 mm x 18.9 mm x 13.5 mm (1.75 x 0.75 x 0.53)
- Operating temperature: -10~60C
- Body material: Plastic
-
JSN-SR04T Waterproof Ultrasonic Sensor Module
Original price was: ₨1,400.00.₨1,299.00Current price is: ₨1,299.00. Quick View- Operating Voltage: 5V DC
- Static Operating Current: 5mA
- Operating Current: 30mA
- Acoustic Emission Frequency: 40kHz
- Maximum range: 4.5m
- Minimum range: 25cm
- Connection pins: +5V, Trig, Echo, GND
- Module Dimensions: 41mm * 28.5mm
- Sensitivity: ~0.5cm
- Sight Angle: <50
- Operating Temperature: -10 ~ 70 C
- Storage Temperature: -20 ~ 80 C
-
E3f-ds30c4 – Photoelectric Switch Sensor Pnp
Original price was: ₨3,000.00.₨1,199.00Current price is: ₨1,199.00. Quick ViewE3F-DS30C4 M18 Diffuse Reflection Photoelectric Switch Sensor 3 Wires NPN NO DC 10-30VDC 200mA 30cm Adjustable in Pakistan.
-
1.3 inch OLED Display 128X64 SSD1306 I2C SH1106
Original price was: ₨1,100.00.₨799.00Current price is: ₨799.00. Quick View- Resolution: 128 X 64 pixels
- Display color: Blue text on black background
- Interface: I2C
- Operating voltage: 3.3V – 5V
- Power consumption: 10-30mA
- Dimensions: 27mm x 27mm x 4.1mm
-
OLED Display Module 12864 0.96 Inch 4Pin
Original price was: ₨600.00.₨549.00Current price is: ₨549.00. Quick View- No need of the backlight
- The display is self-illuminating
- Power requirement is low
- They are offering the large viewing angle
- Full Compatible with Arduino
- Factory configured for SPI protocol (can easily change to IIC)
- Better performance characteristics than traditional LCD and LED displays.
- Only Need 2 I/O Port Control
-
DHT11 Temperature and Humidity Sensor
Original price was: ₨300.00.₨249.00Current price is: ₨249.00. Quick View- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0C to 50C
- Humidity Range: 20% to 90%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: 1C and 1%
-
SIM800L GSM Module Micro Sim Card Board
Original price was: ₨1,799.00.₨1,049.00Current price is: ₨1,049.00. Quick View- Module models: SIM800L (latest module, performance than SIM900)
- Operating voltage: 3.7 to 4.2 V (peak current is 2A)
- Support network: China mobile, China Unicom
- Module size: 2.2 x 1.8cm
- TTL serial port can directly link to MCU. Don’t need a MAX232
- Power on automatic startup, automatic search network
- Onboard one channel indicator light (with signal slow flash, no signal quickly flash)
-
MAX6675 Module + K Type Thermocouple
Original price was: ₨1,500.00.₨719.00Current price is: ₨719.00. Quick View- Thermocouple temperature range: 0 to 450 °C
- Module sensor temperature range (°C): 0 to 1024
- Temperature resolution (°C): 0.25
- Module supply voltage: 3 to 5.5 V
- Module current: 50mA
- Module interface: Serial (SO, SCK, CS) 16 bit SPI compatible
- Termocouple accuracy (0-700°C): 8 LSBs
- Termocouple disconnect detection
-
ESP8266 NodeMCU V1.0 ESP-12E WiFI Module
Original price was: ₨400.00.₨369.00Current price is: ₨369.00. Quick View- Microcontroller: ESP-8266 32-bit
- Clock Speed: 80 MHz
- USB Converter: CP2102
- USB Connector: Micro USB
- Operating Voltage: 3.3V
- Flash Memory: 4 MB
- Digital I/O: 11
- Analog Inputs: 1
- Communications: Serial, SPI. I2C and 1-Wire via software libraries
- WiFi: Built-in 802.11 b/g/n
-
- Working voltage: DC 3.3V-5V
- Working current: 20mA
- Operating temperature: -10~+50
- detection distance :2-40cm
- IO Interface: 4-wire interfaces (-/+/S/EN)
- Output signal: TTL level (low level there is an obstacle, no obstacle high)
- Adjustment: adjust multi-turn resistance 8. Effective angle: 35.7.
- Size: 28mmx23mm
-
- Output controllable: Digital
- Compatible: With any 5V microcontroller such as Arduino.
- Rated through-current: 10A (NO) 5A (NC)
- Control signal: TTL level
- Max. switching voltage: 250VAC/30VDC
- Max. switching current: 10A
- Size: 76mm x 56mm x 17mm
-
Proximity Sensor LM12-3004-PA PNP
Original price was: ₨1,140.00.₨899.00Current price is: ₨899.00. Quick View- Insulating resistance: ≥ 50 M Ω
- Gearing distance: from 2 mm to 7 mm
- Precision of repetition: 0.01
- Ambient temperature: -25˚С to +65˚С
- Gearing speed: 5mm/s
- Rated voltage: 6~36VDC; 90~230VAC
- IP code: IP 67
-
- Material: FR4
- Length: 25mm
- Width: 11mm
- Height: 16mm
- Weight: 1.59g
- Operating Voltage: 5v DC
-
The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption
-
Solar water pump or air cooler pump DC 12V 8watt, Shafi
Original price was: ₨1,500.00.₨749.00Current price is: ₨749.00. Quick ViewThis awesome water pump comes with an adjustable flow and is easy to clean. Strainer protects impeller from damage. Shell is made of high-quality ABS plastic. This pump is a totally submersible flow-adjustable water pump. The motor will automatically cut off the power if it is overheating. The flow can be up to 212GPH. It has good waterproof, has high dielectric strength, and is safe and reliable. Suitable for acid, alkali, and salt environments.
-
MQ2 Gas Sensor Detector Module
Original price was: ₨350.00.₨299.00Current price is: ₨299.00. Quick View- Its dimensions are 36 x 20 x 21 (LxWxH)
- Its weight is 8gm.
- Its operating voltages are plus 5V.
- It can be used to detect LPG, Alcohol, Propane, Hydrogen, CO, and even methane.
- Its analog output voltages are 0V to 5V.
- Its digital output voltages are 0 to 5V.
- Its preheat duration is 20 seconds.
- This sensor can be used as a digital or analog sensor.
- Its sensitivity can be varied by the potentiometer.
-
- Its color is White.
- Alarms diameter is 29mm / 1.14”
- Electronic buzzer height is 15mm / 0.59”
- It has 2 mounting holes. And the distance of the holes is 40mm / 1.57”
- Its rated voltages are 12Volts.
- Its operating voltages are 3 to 24 voltages.
- Its rated current is 20mA.
- Its min sound output at 10cm is 95 Db.
- Its resonant frequency is 3100 to +- 500.
- Its operating temperature is -20 to -80 degrees centigrade.
- It has intermittent sound and mounting holes.
- It has good storage and it allows you to use it for a long time.
-
LCD I2C Module IIC/I2C Serial Interface Adapter
Original price was: ₨300.00.₨219.00Current price is: ₨219.00. Quick View- Operating Voltage: 5V
- Backlight and Contrast is adjusted by potentiometer
- Serial I2C control of LCD display using PCF8574
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 16×2 LCD
- This is another great IIC/I2C/TWI/SPI Serial Interface
- With this I2C interface module, you will be able to realize data display via only 2 wires.
-
MPU9250 IMU 9DOF MPU-9250
Original price was: ₨2,000.00.₨1,650.00Current price is: ₨1,650.00. Quick View- Three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs
- Three 16-bit ADCs for digitizing the accelerometer outputs
- Three 16-bit ADCs for digitizing the magnetometer outputs
- Gyroscope full-scale range of 250, 500, 1000, and 2000/sec (dps)
- Accelerometer full-scale range of 2g, 4g, 8g, and 16g
- Magnetometer full-scale range of 4800T
- I2C and SPI serial interfaces
- Internal Digital Motion Processing engine supports advanced MotionProcessing and low power functions such as gesture recognition using programmable interrupts
- Power supply: 3-5v
-
- Photosensitivity is high
- Response time is fast
- Simple to use
- Sensitivity is adjustable
- Detection angle is 600,
- It is responsive to the flame range.
- Accuracy can be adjustable
- Operating voltage of this sensor is 3.3V to 5V
- Analog voltage o/ps and digital switch o/ps
- The PCB size is 3cm X 1.6cm
- Power indicator & digital switch o/p indicator
- If the flame intensity is lighter within 0.8m then the flame test can be activated, if the flame intensity is high, then the detection of distance will be improved.
-
- 3.3-5.5V Input
- 1-1.5mA measuring current
- 40-50 uA standby current
- Humidity from 0-100% RH
- -40-80C Temperature Range
- +-2% RH accuracy
- +-0.5 degrees C
-
- Working voltage: 5V
- Pulses per 360-degree revolution: 20
- Push button shaft On/Off switch
- Threaded shaft for panel mounting, also 2 mounting screw holes on the circuit board
- Standard “D” shaft, you can purchase knobs to give it a finished look
-
BMP180/GY68 Pressure Sensor
Original price was: ₨300.00.₨239.00Current price is: ₨239.00. Quick View- 1.8V to 3.6V Supply Voltage
- Low power consumption – 0.5uA at 1Hz
- I2C interface
- Max I2C Speed: 3.5Mhz
- Very low noise – up to 0.02hPa (17cm)
- Fully calibrated
- Pressure Range: 300hPa to 1100hPa (+9000m to -500m)
- Size: 13mm x 10mm