-
-38%
IN4001 Diode 4001 Rectifier Diode
Original price was: ₨8.00.₨5.00Current price is: ₨5.00. Quick View- Package Type: Available in DO-41 & SMD Packages
- Diode Type: Silicon Rectifier General Usage Diode
- Max Repetitive Reverse Voltage is: 50 Volts
- Average Fwd Current: 1000mA
- Non-repetitive Max Fwd Current: 30A
- Max Power Dissipation is: 3W
- Max Storage & Operating temperature Should Be: -55 to +175 Centigrade
-
- Operating Voltage: 5V, 10V, 15V DC
- Maximum Input Current: 1uA
- Hysteresis Voltage Typically 0.9 V at VDD: 5 V and 2.3 V at VDD: 10 V
- Noise Immunity Greater Than 50%
- Unlimited input rise and fall times
-
- Dynamic dV/dt rating
- Repetitive avalanche rated
- Fast switching
- Ease of paralleling
- Simple drive requirements
-
-17%
- Resistance: 503 50K Ohm,
- Resistor Tolerance: ±10% Max
- Max Voltage: 50V
- Rating Power: 0.1W
- Technology: Carbon Film
- Adjustment Type: Top Adjustment
-
N-Channel Power MOSFET provide the circuit designer with the best combination of fast switching, ruggedized device design, low on-resistance and cost-effectiveness.
-
-14%
- Type: NPN
- Collector-Emitter Voltage, max: 140 V
- Collector-Base Voltage, max: 140 V
- Emitter-Base Voltage, max: 5 V
- Collector Current − Continuous, max: 10 A
- Collector Dissipation: 100 W
- DC Current Gain (hfe): 55 to 160
- Transition Frequency, min: 30 MHz
- Operating and Storage Junction Temperature Range: -55 to +150 °C
- Package: TO-3P
-
BT134 Triac – 600V – 4A (BT134-600E) Triac they are used in AC switching and control applications with current ratings from under 1A to 40A rms. Since TRIACs are bi-directional switching devices they are commonly used for switching AC applications. It has Maximum Terminal current: 4A, Max Terminal Voltage is 600 V, Gate trigger current: 25mA & On-state Gate voltage: 1.7V.
-
-36%
LM338T 5A Adjustable Voltage Regulator LM-338T
Original price was: ₨45.00.₨29.00Current price is: ₨29.00. Quick ViewLM338T 5A Adjustable Voltage Regulator LM-338T is adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 5 A over a 1.2-V to 32-V output range. They are exceptionally easy to use and require only 2 resistors to set the output voltage.
-
- Dual inputQuad NAND gate operation.
- Input voltage range: -0.5 to VDD +5V
- Power dissipation of 100mW per logic change.
- It is available in different outline packages
- The propagation delay time is 60ns
- All input and output pins are buffered for high throughput
- The output characteristics are standardized symmetric
- CD4011 draws a maximum input current of 1 Ampere at 18 volts
- Offers different noise margin level according to the input voltage level
- Temperature operating range is -55C to +125C
-
10K ohm Trimmer Trim Pot Variable Resistor 3296W 3296 Variable Resistor is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer. The potentiometer essentially functions as a variable voltage divider. The resistive element can be seen as two resistors in series(potentiometer resistance), where the wiper position determines the resistance ratio of the first resistor to the second resistor. A potentiometer is also commonly known as a potentiometer or pot. The most common form of potmeter is the single turn rotary potmeter. This type of pot is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, wirewound, conductive plastic or metal film.
-
Resistors are electronic components which have a specific, never-changing electrical resistance. The resistor’s resistance limits the flow of electrons through a circuit. They are passive components, meaning they only consume power (and can’t generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.
-
- Inverting IC that can convert High logic level to Low level
- High source and Sink Current as it has the capability of driving 2 TTL Loads at 5V over full temperature range.
- 100% Tested for Quiescent Current at 20 V
- Maximum Input Current of 1A at 18 V Over Full Package Temperature Range; 100 nA at 18 V and 25C
- 5-V, 10-V, and 15-V Parametric Ratings
- It is available in 16 pin packages of PDIP, SOIC, TSSOP, SO.
- Special input protection to protect inputs against static discharges.
-
The CD4081 quad gate is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors. They have equal source and sink current capabilities and conform to standard B series output drive. The devices also have buffered outputs which improve transfer characteristics by providing very high gain. All inputs protected against static discharge with diodes to VDD and VSS.
-
-34%
CD4538 – Dual Monostable Multivibrator
Original price was: ₨150.00.₨99.00Current price is: ₨99.00. Quick View- Wide supply voltage range 3.0V to 15V
- High noise immunity 0.45 VCC (typ.)
- Low power Fan out of 2 driving 74L TTL compatibility or 1 driving 74LS
- New formula: PWOUT e RC (PW in seconds, R in Ohms, C in Farads)
- g1.0% pulse-width variation from part to part (typ.) Wide pulse-width range 1 ms to %
- Separate latched reset inputs
- Symmetrical output sink and source capability
- Low standby current 5 nA (typ.) @ 5 VDC Y Pin compatible to CD4528
-
A potentiometer knob is an accessory that is used as a control knob for a potentiometer.
-
-22%
500K Ohm Rotary Potentiometer / Variable Resistor
Original price was: ₨50.00.₨39.00Current price is: ₨39.00. Quick View500K Ohm Rotary Potentiometer / Variable Resistor is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer. The potentiometer essentially functions as a variable voltage divider. The resistive element can be seen as two resistors in series(potentiometer resistance), where the wiper position determines the resistance ratio of the first resistor to the second resistor. A potentiometer is also commonly known as a potentiometer or pot. The most common form of potmeter is the single turn rotary potmeter. This type of pot is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, wirewound, conductive plastic or metal film.
-
-33%
- Technology Family: CD4000
- VCC (Min) (V): 3
- VCC (Max) (V): 18
- Channels (#): 4
- Inputs per channel: 2
- IOL (Max) (mA): 6.8
- IOH (Max) (mA): -6.8
- Input type Standard: CMOS
- Output type: Push-Pull
- 5V–10V–15V parametric ratings
- Symmetrical output characteristics
- Speed: (tpd > 50ns)
- Data rate (Max) (Mbps): 8
- Rating: Catalog
- Operating temperature range (C): -55 to 125
-
The MC34063A Series is a monolithic control circuit containing the primary functions required for dc-to-dc converters. These Buck Boost Inverting Switching Regulators consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. Operation from 3.0 V to 40 V Input. Output Switch Current to 1.5 A.
-
It is an integrated circuit that converts the signals from the RS232 serial port to the proper signal which is used in the TTL compatible digital logic circuits. The MAX232 can convert the signals like RX, TX, CTS, and RTS and it is a dual driver/receiver.
-
- Wide supply voltage range: 3V to 15V
- Low power: 100 nW (typ.)
- High noise immunity: 0.45 VDD (typ.)
- Separate SET and RESET inputs for each latch
- NOR and NAND configuration
- 3-STATE output with common output enable
-
-14%
- Type –NPN
- Collector-Emitter Voltage: 400V
- Collector-Base Voltage: 450V
- Emitter-Base Voltage: 7V
- Collector Current: 10A
- Collector Dissipation – 80W
- DC Current Gain (hfe) – 10
- Operating and Storage Junction Temperature Range -55 to +150C
-
2N4401 is an NPN bipolar junction transistor that is mainly designed for general purpose, small signal, and switching applications.
-
Resistors are electronic components which have a specific, never-changing electrical resistance. The resistor’s resistance limits the flow of electrons through a circuit. They are passive components, meaning they only consume power (and can’t generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.
-
-9%
- Internally frequency compensated for unity gain
- Large DC voltage gain 100 dB
- Wide bandwidth (unity gain) 1 MHz (temperature compensated)
- Very low supply current drain (700 A) essentially independent of supply voltage
- Low input biasing current 45 nA (temperature compensated)
- Low input offset voltage 2 mV and offset current: 5 nA
- Input common-mode voltage range includes ground
-
- Bi-Polar PNP Transistor
- DC Current Gain (hFE) is 300 maximum
- Continuous Collector current (IC) is 200mA
- Emitter Base Voltage (VBE) is 5V
- Base Current(IB) is 5mA maximum
- Collector Emitter Voltage (VCE) is 40V
- Collector Base Voltage (VCB) is 40V
- Available in To-92 Package
-
-22%
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer. The potentiometer essentially functions as a variable voltage divider. The resistive element can be seen as two resistors in series(potentiometer resistance), where the wiper position determines the resistance ratio of the first resistor to the second resistor. A potentiometer is also commonly known as a potentiometer or pot. The most common form of potmeter is the single turn rotary potmeter. This type of pot is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, wirewound, conductive plastic or metal film.
-
-22%
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer. The potentiometer essentially functions as a variable voltage divider. The resistive element can be seen as two resistors in series(potentiometer resistance), where the wiper position determines the resistance ratio of the first resistor to the second resistor. A potentiometer is also commonly known as a potentiometer or pot. The most common form of potmeter is the single turn rotary potmeter. This type of pot is often used in audio volume control (logarithmic taper) as well as many other applications. Different materials are used to construct potentiometers, including carbon composition, cermet, wirewound, conductive plastic or metal film.
-
ULN2004 Features
- Output current (single output): 500mA (MAX.)
- High sustaining voltage output: 50V (MIN.)
- Output clamp diodes
- Inputs compatible with various types of logic
-
- Wide supply voltage range 3.0V to 15V
- Low power 10 nW (typ.)
- High noise immunity 0.45 VDD (typ.)
- Buffered Inputs and Outputs
- Standard Symmetrical Output Characteristics
- 100% Tested for Maximum Quiescent Current at 20V
- 5V, 10V and 15V Parametric Ratings
- Maximum Input Current of 1A at 18V Over Full Package-Temperature Range; 100nA at 18V and +25oC
-
-16%
- Logic Type: INVERTER / NOR / NAND
- Output Current: 6.8mA
- Supply voltage range: 3V to 18V
- Package Type: DIP
- Pin number: 14
- Operating temperature range: -55 ° C to +125 ° C
- Surface Mount Devices: through-hole mounting
-
LM324 Operational Amplifier IC LM-324 consist of four independent high-gain frequency-compensated operational amplifiers that are designed specifically to operate from a single supply or split supply over a wide range of voltages. Wide Supply Ranges Single Supply: 3 V to 32 V (26 V for LM2902) Dual Supplies: 1.5 V to 16 V (13 V for LM2902) Low Supply-Current Drain.
-
Specifications:
- Power (Watts) 1W
- Resistant 22K OHMS
- Tolerance +- 5%
- Resistor Type Carbon Film
- Lead Free
-
- Fast Switching Applications
- Uninterruptible Power Supplies
- Battery Chargers
- Battery Management Systems
- Solar Battery Chargers
- Solar Uninterruptible Power Supplies
- Motor Driver Applications
- Telecommunication Applications
- Computer Related Applications
-
- Low saturation voltage
- Simple drive requirements
- High safe operating area
- For low distortion complementary designs
- Easy to carry and handle
-
- HF applications in radio and television receivers
- FM tuners
- Low noise AM mixer-oscillators
- IF amplifiers in AM/FM receivers
-
-28%
- Small Signal NPN Transistor
- Current Gain (hFE): 450 (maximum)
- Continuous Collector current (IC) is 100mA
- Collector-Emitter voltage (VCEO) is 45V
- Collector-Base voltage (VCB0) is 50V
- Emitter Base Voltage (VBE0) is 6V
- Available in To-18 Metal can Package
-
-40%
- Local sensor accuracy (Max) (+/- C): 0.5
- Operating temperature range (C): -40 to 110,-55 to 150,0 to 100,0 to 70
- Supply voltage (Min) (V): 4
- Supply voltage (Max) (V): 30
- Supply current (Max) (uA): 14
- Sensor gain (mV/Deg C): 10
- Rating: Catalog
- Features: UL Recognized
- Interface: Analog Output
-
-23%
- Case: R-6
- Case Material: Molded Plastic. UL Flammability Classification Rating 94V-0 Moisture Sensitivity: Level 1 per J-STD-020C
- Terminals: Finish Tin. Axial Leads, Solderable per MILSTD-202, Method 208
- Polarity: Color Band Indicates Cathode
- Approximate Weight: 2.1 grams
-
The 7408 is a QUAD 2-Input AND gates and contains four independent gates each of which performs the logic AND function. It comes in 14-pin DIP package. 7408 AND Gate IC 74HC244 74244 Octal Buffers & Line Driver IC in Pakistan
-
-11%
Transformer 12V Center Tapped 3AMP
Original price was: ₨620.00.₨549.00Current price is: ₨549.00. Quick View- Output current: 3A
- Supply voltage: 220-230VAC
- Output voltage: 12-0-12VAC
- Soft Iron Core
- 1A Current Drain
-
Resistors are electronic components which have a specific, never-changing electrical resistance. The resistors resistance limits the flow of electrons through a circuit. They are passive components, meaning they only consume power (and cant generate it). Resistors are usually added to circuits where they complement active components like op-amps, microcontrollers, and other integrated circuits. Commonly resistors are used to limit current, divide voltages, and pull-up I/O lines.
-
-13%
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer.
-
- High-Voltage Types (20V Rating)
- CD4071BMS Quad 2-Input OR Gate
- CD4072BMS Dual 4-Input OR Gate
- CD4075BMS Triple 3-Input OR Gate
- Medium Speed Operation: tPHL, tPLH = 60ns (typ) at 10V
- 100% Tested for Quiescent Current at 20V
- Maximum Input Current of 1A at 18V Over Full Package Temperature Range; 100nA at 18V and +25oC
- Standardized Symmetrical Output Characteristics
-
- Low Voltage and Standard-Voltage Operation
- 2-wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression
- Bi-directional Data Transfer Protocol
- 100kHz and 400kHz Compatibility
- Write Protect Pin for Hardware Data Protection
- 8-byte Page (1K, 2K), 16-byte Page (4K, 8K, 16K) Write Modes
- Partial Page Writes are Allowed
- Self-timed Write Cycle (10mS max)
-
-46%
TL084 circuits JFET Input Op-amp
Original price was: ₨200.00.₨109.00Current price is: ₨109.00. Quick View- Input Offset Voltage Options of 6.0 mV and 15 mV Max
- Low Input Bias Current: 30 pA
- Low Input Offset Current: 5.0 pA
- Wide Gain Bandwidth: 4.0 MHz
- High Slew Rate: 13 V/s
- Low Supply Current: 1.4 mA per Amplifier
- High Input Impedance: 1012
-
-36%
LM358 LM358P DIP8 LM 358 LM358N DIP-8 IC
Original price was: ₨45.00.₨29.00Current price is: ₨29.00. Quick View- Very low supply current drain (500 A) essentially independent of supply voltage
- Low input offset voltage: 2 mV
- Input common-mode voltage range includes ground
- Differential input voltage range equal to the power supply voltage
- Large output voltage swing: 0V to V+ 1.5V
- Internally frequency compensated for unity gain
- Large dc voltage gain: 100 dB
- Wide bandwidth (unity gain): 1 MHz (temperature compensated)
-
-50%
HI-LINK 120VAC-220VAC 5VDC 3W Power Supply
Original price was: ₨1,500.00.₨749.00Current price is: ₨749.00. Quick View- Input voltage:90-240 VAC
- Low ripple and low noise
- Output overload and short circuit protection
- High efficiency, high power density
- Low power consumption, environmental protection, no-load loss <0.1W
- 100% load aging and testing
- Operation Temperature: -20 — +60
- Store Temperature: -40 — +80
- Relative humidity: 5 — 95 %
- Cooling way by radiation
- Atmospheric pressure: 80—106 Kpa
- Sea level elevation: 2000 m
- Rated input voltage: 100-240 VAC
- Input voltage range: 90-264 VAC
- Meets UL and CE requirements
- Ultra-thin and ultra-small
-
-22%
74HC595 74HC595D Shift Register
Original price was: ₨90.00.₨70.00Current price is: ₨70.00. Quick View74HC595 8-BIT SERIAL-IN SERIAL OR PARALLEL-OUT SHIFT REGISTER contain an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. The storage register has parallel 3-state outputs. Separate clocks are provided for both the shift and storage register. The shift register has a direct overriding clear (SRCLR) input, serial (SER) input, and serial outputs for cascading. When the output-enable (OE) input is high, the outputs are in the high-impedance state.