Arduino & IOT Boards

Default sorting
Show
48
  • -41%

    GY-291 ADXL345 3-Axis Accelerometer Module

    Accelero, Gyro. IMU, Magneto
    (0)
    Original price was: ₨590.00.Current price is: ₨349.00. Quick View
    • Main Chip: ADXL345
    • Model: GY-291
    • Power Supply: 3-5V
    • Means of Communication: IIC / SPI Communication Protocol
    • Measuring Range: ±2g /±16g
    • Digital-Output Triple-Axis Accelerometer with a Programmable Full-Scale Range of ±2g, ±4g, ±8g and ±16g and Integrated 16-bit ADCs
    • Accelerometer Normal Operating Current: 450µA
    • Ultralow Power: as low as 23 μA in Measurement Mode and 0.1 μA in Standby Mode at VS = 2.5 V (typical)
    • Sleep Mode Current: 8µA
    • Communication: SPI (3- and 4-wire) and I2C Digital Interfaces
    • User-Programmable Interrupts
    • Wake-On-Motion Interrupt for Low Power Operation of Applications Processor
  • -12%

    Gy-61 Triple Axis Accelerometer Adxl335

    Accelero, Gyro. IMU, Magneto
    (1)
    Original price was: ₨1,990.00.Current price is: ₨1,749.00. Quick View
    1. 3V-6V DC Supply Voltage
    2. Onboard LDO Voltage regulator
    3. Can be interfaced with a 3V3 or 5V Microcontroller.
    4. All necessary components are populated.
    5. Ultra Low Power: 40uA in measurement mode, 0.1uA in standby@ 2.5V
    6. Tap/Double Tap Detection
    7. Free-Fall Detection
    8. Analog output
    9. Build in ultra-low noise linear LDO voltage regulator
    10. Built-in onboard filters, which reduce noise from the motor and other high-current electronics
    11. All sensors connected to the I2C bus
    12. You can easily select two I2C addresses for MPU6050 by soldered jumper
    13. Power LED
    14. Build in Logic level converter for I2C
    15. Dimensions 20x16mm
    16. Designed for 5V logic level
  • -10%
    Out Of Stock

    GPS Arduino Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨5,350.00.Current price is: ₨4,799.00. Quick View

    This is a GPS module breakout board with SD storage based on the u-blox NEO-6M GPS and its foot print is compatible with arduino boards . This board features an SD card socket, which makes it convenient for building data loggers.

  • -14%

    W5100 Ethernet Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨3,500.00.Current price is: ₨2,999.00. Quick View
    • Operating voltage 5V (supplied from the Arduino Board)
    • Ethernet Controller: W5100 with internal 16K buffer
    • Connection speed: 10/100Mb
    • Connection with Arduino on SPI port
    • The Shield contains a number of informational LEDs
    • PWR: indicates that the board and shield are powered
    • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
    • FULLD: indicates that the network connection is full duplex
    • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
    • RX: flashes when the shield receives data
    • TX: flashes when the shield sends data
    • TX: flashes when the shield sends data
    • COLL: flashes when network collisions are detected
  • Out Of Stock

    Arduino WiFi Shield CC3000

    Arduino & IOT Boards
    (0)
    ₨2,800.00 Quick View
    1. Based on TI CC3000 WIFI module.
    2. Use SPI communication .
    3. Integrated 3.3V regulator .
    4. Level shifter integrated .
    5. Integrated ceramic antenna .
    6. It has a connector for external antenna WIFI
    7. Compatible with Arduino UNO, Mega, Leondardo & Micro
    8. Antenna: Onboard Ceramic
    9. MicroSD card slot onboard
    10. Reset button
    11. Communication Protocol: SPI
    12. Connects via IEEE 802.11 b/g networks
    13. Tx Bandwidth: 11Mbps
    14. Tx Sensitivity: +/-18dBm
    15. Rx sensitivity: -86dBm
    16. IRQ pin for interrupts (useful for asynchronous connections)
    17. Supports WEP, WPA, WPA2, TKIP and AES
    18. TCP and UDP Client & Server Modes available
    19. Max Concurrent TCP/UDP Sockets: 4
    20. TCP/IP stack is built in.