Module

Default sorting
Show
48
  • -23%

    Ph Sensor Gravity Sensor Module

    Arduino & IOT Boards
    (0)
    Original price was: ₨7,800.00.Current price is: ₨5,999.00. Quick View
    1. Module Power: 5.00V
    2. Module Size : 43 x 32mm(1.69×1.26″)
    3. Measuring Range :0 – 14PH
    4. Measuring Temperature: 0 – 60 ℃
    5. Accuracy : ± 0.1pH (25 ℃)
    6. Response Time: ≤ 1min
    7. pH Sensor with BNC Connector
    8. pH2.0 Interface ( 3 foot patch )
    9. Gain Adjustment Potentiometer
    10. Power Indicator LED
  • -66%

    KY-009 RGB LED SMD module

    Arduino & IOT Boards
    (0)
    Original price was: ₨200.00.Current price is: ₨69.00. Quick View
    • Using 5050 full-color LED.
    • RGB tricolour current一limiting resistance to prevent burnout.
    • Through the PWM adjusting three primary colors can be mixed to obtain different colors.
    • With a variety of single一chip interfaces.
    • Working Voltage: 5V.
    • LED Drive Mode: Common cathode driver.
  • -10%

    A3967 Stepper Motor Driver Module

    Arduino & IOT Boards
    (0)
    Original price was: ₨400.00.Current price is: ₨360.00. Quick View

    This EasyDriver compatible stepper motor driver module utilizes the Allegro A3967SLB micro-stepping driver to proved a simple and compact means of driving bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors from a microcontroller. By default, the module will accept a 5V TTL step and direction signal from the microcontroller to stop the motor in either full, half, quarter, and eighth-step modes. By shorting jumper SJ2 it can also be configured to be compatible with 3.3V microcontrollers that are not 5V tolerant. An onboard potentiometer allows for setting maximum drive current.

  • -20%
    Out Of Stock

    xbee Shield

    Communication Modules
    (0)
    Original price was: ₨2,115.00.Current price is: ₨1,692.00. Quick View
    • 3.3V @ 50mA
    • 250kbps Max data rate
    • 1mW output (+0dBm)
    • 300ft (100m) range
    • Wire antenna
    • Fully FCC certified
    • 6 10-bit ADC input pins
    • 8 digital IO pins
    • 128-bit encryption
    • Local or over-air configuration
    • AT or API command set
  • -21%
    Out Of Stock

    Arduino 28BYJ48 Stepper Motor

    Arduino & IOT Boards
    (0)
    Original price was: ₨440.00.Current price is: ₨349.00. Quick View

    Arduino 28BYJ48 Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug. Motor: Diameter: 28mmVoltage: 5VStep angle: 5.625 x 1/64Reduction ratio: 1/64ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31x35mmPackage included:1 x ULN2003 driver board1 x 28BYJ-48 stepper motor Options:

  • -8%
    Out Of Stock

    PPM Encoder

    Arduino & IOT Boards
    (0)
    Original price was: ₨1,300.00.Current price is: ₨1,200.00. Quick View

    PPM encoder is the role of the receiver output of multiple channel PWM signal encoded into PPM composite signal output, single-wire connection to support the flight control.

  • -42%

    SIM800L GSM Module Micro Sim Card Board

    Communication Modules
    (0)
    Original price was: ₨1,799.00.Current price is: ₨1,049.00. Quick View
    • Module models: SIM800L (latest module, performance than SIM900)
    • Operating voltage: 3.7 to 4.2 V (peak current is 2A)
    • Support network: China mobile, China Unicom
    • Module size: 2.2 x 1.8cm
    • TTL serial port can directly link to MCU. Don’t need a MAX232
    • Power on automatic startup, automatic search network
    • Onboard one channel indicator light (with signal slow flash, no signal quickly flash)
  • -52%
    Out Of Stock

    MAX6675 Module + K Type Thermocouple

    Arduino & IOT Boards
    (0)
    Original price was: ₨1,500.00.Current price is: ₨719.00. Quick View
    • Thermocouple temperature range: 0 to 450 °C
    • Module sensor temperature range (°C): 0 to 1024
    • Temperature resolution (°C): 0.25
    • Module supply voltage: 3 to 5.5 V
    • Module current: 50mA
    • Module interface: Serial (SO, SCK, CS) 16 bit SPI compatible
    • Termocouple accuracy (0-700°C): 8 LSBs
    • Termocouple disconnect detection
  • -26%

    RGB module Normal

    Arduino & IOT Boards
    (0)
    Original price was: ₨200.00.Current price is: ₨149.00. Quick View
    • Material: FR4
    • Length: 25mm
    • Width: 11mm
    • Height: 16mm
    • Weight: 1.59g
    • Operating Voltage: 5v DC
  • -23%
    Out Of Stock

    Sim 800A GSM

    Communication Modules
    (0)
    Original price was: ₨650.00.Current price is: ₨500.00. Quick View

    The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption

  • -25%

    RGB SMD MODULE FULL COLOR

    Arduino & IOT Boards
    (0)
    Original price was: ₨200.00.Current price is: ₨150.00. Quick View

    This is the SMD RGB LED Common Cathode Module, These module has 3 separate LEDs the Red, Green and Blue which can be individually driven by applying a voltage to the appropriate module pin this example code is uses the Arduino analogWrite(PWM) function to cycle through the full possible output colors this smd led module is capable of producing a rainbow color scheme.

  • -45%

    KY-021 Mini Magnetic Reed Module for Arduino

    Arduino & IOT Boards
    (0)
    Original price was: ₨270.00.Current price is: ₨149.00. Quick View
    • Operating voltage: 3.3V to 5V
    • Output type: Digital
    • Dimensions: 20 x 15 x 7mm
    • Input voltage: 3.3~5v
    • Weight: 1.2g
    • Reed switch: Normally open
    • Reed switch sensitivity: 30 gauss
    • Operating temperature: -20°C to 85°C
    • Storage temperature: -40°C to 125°C
  • -13%

    RFID RDM 6300

    Communication Modules
    (0)
    Original price was: ₨800.00.Current price is: ₨699.00. Quick View
    • Operating frequency: 125 kHz
    • Baud rate: 9600
    • Interface: TTL level RS232 format
    • Working voltage: DC 5V
    • Working current: <50mA
    • Receive distance: 20~50mm
    • Dimension (mm): 38.5 x 20
    • Weight: 7g
  • -14%

    LM393 Microphone Amplifier

    Arduino & IOT Boards
    (0)
    Original price was: ₨300.00.Current price is: ₨259.00. Quick View
    1. Detectable sound signal size
    2. Built-in filter-rectifier circuit, DC signal output
    3. Good sensitivity, built-in amplifier circuit, adjustable gain
    4. Voltage signal for sound intensity can be obtained by AD conversion
    5. Analog voltage signal output, signal amplitude VCC/2
    6. Compatible for Arduino sensor interface.
  • -16%
    Out Of Stock

    Lillypad

    Arduino & IOT Boards
    (0)
    Original price was: ₨900.00.Current price is: ₨760.00. Quick View

    LilyPad is a programmable sewable system for creating textile with the help of electronics. The pad is programmed through arduino and used for textile projects using conductive thread.

  • -15%

    Arduino Sensor Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨350.00.Current price is: ₨299.00. Quick View
    • It has a Pin 13 LED pilot.
    • It has D0-D13 IO ports.
    • A0-A5 analog IO ports.
    • It contains a reset button.
    • It also contains a Power LED.
    • It has an SD card interface.
    • It contains an Ultrasonic interface.
    • This expansion board has an RS232 interface.
    • It has a Bluetooth interface.
    • It has an APC220 interface.
    • IIC interface.
    • 12864 LCD Parallel interfaces.
    • It contains 12864 LCD Serial Interface
  • Out Of Stock

    XBee Pro 60mW Wire Antenna

    Communication Modules
    (0)
    ₨6,799.00 Quick View

    INTRODUCTION

    This is the very popular 2.4GHz XBee XBP24-AWI-001 module from Digi (formerly known as Maxstream). The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
  • -41%

    XBee 2mW Wire Antenna – Series 2 (ZB)

    Communication Modules
    (0)
    Original price was: ₨15,000.00.Current price is: ₨8,799.00. Quick View

    This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.

  • -30%
    Out Of Stock

    XBee 1mW Wire Antenna

    Communication Modules
    (0)
    Original price was: ₨6,500.00.Current price is: ₨4,549.00. Quick View

    INTRODUCTION

    This is the very popular 2.4GHz XBee module from Digi (formally Maxstream). These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
    Pair a couple of these XBees with a Regulated Explorer, and a USB Explorer and you’ve got a great gift for that special electronics geek!
  • Out Of Stock

    Telemetry 3DR TTL

    Communication Modules
    (0)
    ₨3,800.00 Quick View

    The Radio telemetry system base on 3DR Radio system and 100% compatible.

    It’s designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. Its available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).

    The system provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.

    Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.

  • -20%

    Xbee shield V03

    Communication Modules
    (0)
    Original price was: ₨5,000.00.Current price is: ₨3,999.00. Quick View
    This shield V03 can achieve a simple two crunodal ZigBee network, achieve wireless communication between Ardu, and allows the Ardu to wireless communicate over a modified ZigBee protocol using the popular XBee module.
    It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.
  • Out Of Stock

    ZigBee XCore2530 1500M

    Communication Modules
    (0)
    ₨1,950.00 Quick View

    ZigBee module, features the CC2530F256 onboard, farther communication distance with PA

    Overview

    XCore2530 is a ZigBee module based on CC2530F256.

    Basically this module can be used in two aspects :

    • Develop application with the provided firmware
      Combined with our provided firmware, this is a simple ZigBee wireless UART module, just as easy to use as any other UART module, and requires NO knowledge about the complicate ZigBee Specification
    • Develop your own firmware
      In this case, you should start from the very underlying to create your solution, what’s more, debuggers (like CC Debugger) and knowledge about ZigBee Specification are also required
  • -20%
    Out Of Stock

    XBee Pro 60mW PCB Antenna – Series 1

    Communication Modules
    (0)
    Original price was: ₨7,500.00.Current price is: ₨5,999.00. Quick View

    This is the very popular 2.4GHz XBee XBP24-ACI-001 module from Digi. The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.

  • -17%
    Out Of Stock

    XBee 2mW PCB Antenna – Series 2 (ZigBee Mesh)

    Communication Modules
    (0)
    Original price was: ₨6,000.00.Current price is: ₨4,999.00. Quick View

    This is the XBee XB24-Z7CIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
    These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
    This Xbee also has a chip antenna which is basically a small chip that acts as an antenna. Quick, easy, cheap, and not in the way.

  • -10%
    Out Of Stock

    GPS Arduino Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨5,350.00.Current price is: ₨4,799.00. Quick View

    This is a GPS module breakout board with SD storage based on the u-blox NEO-6M GPS and its foot print is compatible with arduino boards . This board features an SD card socket, which makes it convenient for building data loggers.

  • -14%

    W5100 Ethernet Shield

    Arduino & IOT Boards
    (0)
    Original price was: ₨3,500.00.Current price is: ₨2,999.00. Quick View
    • Operating voltage 5V (supplied from the Arduino Board)
    • Ethernet Controller: W5100 with internal 16K buffer
    • Connection speed: 10/100Mb
    • Connection with Arduino on SPI port
    • The Shield contains a number of informational LEDs
    • PWR: indicates that the board and shield are powered
    • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
    • FULLD: indicates that the network connection is full duplex
    • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
    • RX: flashes when the shield receives data
    • TX: flashes when the shield sends data
    • TX: flashes when the shield sends data
    • COLL: flashes when network collisions are detected
  • Out Of Stock

    Arduino WiFi Shield CC3000

    Arduino & IOT Boards
    (0)
    ₨2,800.00 Quick View
    1. Based on TI CC3000 WIFI module.
    2. Use SPI communication .
    3. Integrated 3.3V regulator .
    4. Level shifter integrated .
    5. Integrated ceramic antenna .
    6. It has a connector for external antenna WIFI
    7. Compatible with Arduino UNO, Mega, Leondardo & Micro
    8. Antenna: Onboard Ceramic
    9. MicroSD card slot onboard
    10. Reset button
    11. Communication Protocol: SPI
    12. Connects via IEEE 802.11 b/g networks
    13. Tx Bandwidth: 11Mbps
    14. Tx Sensitivity: +/-18dBm
    15. Rx sensitivity: -86dBm
    16. IRQ pin for interrupts (useful for asynchronous connections)
    17. Supports WEP, WPA, WPA2, TKIP and AES
    18. TCP and UDP Client & Server Modes available
    19. Max Concurrent TCP/UDP Sockets: 4
    20. TCP/IP stack is built in.