W5100 Ethernet Shield

3,500.00 Original price was: ₨3,500.00.2,999.00Current price is: ₨2,999.00.
  • Operating voltage 5V (supplied from the Arduino Board)
  • Ethernet Controller: W5100 with internal 16K buffer
  • Connection speed: 10/100Mb
  • Connection with Arduino on SPI port
  • The Shield contains a number of informational LEDs
  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected

W5100 Ethernet Shield

W5100 Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

The Ethernet Shield has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.
There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino, Crowduino and Mega (using the Ethernet library). The onboard microSD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4.

Features:

With this Ethernet Shield, your Arduino board can be used to connect to the internet.

  • Can be used as a server or client.
  • Directly plug the puzzle board, no soldering is required.
  • Controller: W5100 with internal 16K buffer
  • Connection speed: 10/100Mb
  • This Arduino Ethernet Shield which is based on the Wiznet W5100 Ethernet Chip gives you an easy way to get your Arduino Online.
  • It is directly supported by Arduino’s official Ethernet Library.
  • It adds a micro-SD card slot, which can be used to store files for serving over the network.
  • It is compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560) and can be accessed using the SD library.
  • The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP.
  • It supports up to four simultaneous socket connections.
  • Use the Ethernet library to write sketches which connect to the internet using the shield.
  • Fits all versions of Arduino Main board,2009, UNO, mega 1280, mega 2560.
  • Size:7cm x 5.4cm x 2.4cm – 2.76inch x 2.12inch x 0.94inch.
  • MAC address: 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };.

Specification

  • Operating voltage 5V (supplied from the Arduino Board)
  • Ethernet Controller: W5100 with internal 16K buffer
  • Connection speed: 10/100Mb
  • Connection with Arduino on SPI port
  • The Shield contains a number of informational LEDs
  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected

Reviews

There are no reviews yet.

Be the first to review “W5100 Ethernet Shield”

Your email address will not be published. Required fields are marked *

3,500.00 Original price was: ₨3,500.00.2,999.00Current price is: ₨2,999.00.