-
-20%
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
-
-15%
The ProtoShield makes it easy for you to design custom circuits. You can easily solder TH or SMD ICs on the prototyping area to test them with your Arduino board. The SMD area is designed for a maximum of 24 pins SOIC integrated circuit and the TH area contains a lot of space for the needed components around your project. You can even stick a mini breadboard (not included) on the protoarea for solderless operation. The proto area includes also two power lines (IOREF and GND), two LEDs pads and SPI signals breakout pads for boards with SPI only on the ICSP header like Zero.
-
-49%
- It has a nice standard 0.1×0.1 prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- A IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- A surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out!
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
- It has a nice standard 0.1×0.1 prototyping grid with big pads
-
-15%
- It has a Pin 13 LED pilot.
- It has D0-D13 IO ports.
- A0-A5 analog IO ports.
- It contains a reset button.
- It also contains a Power LED.
- It has an SD card interface.
- It contains an Ultrasonic interface.
- This expansion board has an RS232 interface.
- It has a Bluetooth interface.
- It has an APC220 interface.
- IIC interface.
- 12864 LCD Parallel interfaces.
- It contains 12864 LCD Serial Interface
-
Out Of Stock- Based on TI CC3000 WIFI module.
- Use SPI communication .
- Integrated 3.3V regulator .
- Level shifter integrated .
- Integrated ceramic antenna .
- It has a connector for external antenna WIFI
- Compatible with Arduino UNO, Mega, Leondardo & Micro
- Antenna: Onboard Ceramic
- MicroSD card slot onboard
- Reset button
- Communication Protocol: SPI
- Connects via IEEE 802.11 b/g networks
- Tx Bandwidth: 11Mbps
- Tx Sensitivity: +/-18dBm
- Rx sensitivity: -86dBm
- IRQ pin for interrupts (useful for asynchronous connections)
- Supports WEP, WPA, WPA2, TKIP and AES
- TCP and UDP Client & Server Modes available
- Max Concurrent TCP/UDP Sockets: 4
- TCP/IP stack is built in.
-
-10%
Out Of StockThis is a GPS module breakout board with SD storage based on the u-blox NEO-6M GPS and its foot print is compatible with arduino boards . This board features an SD card socket, which makes it convenient for building data loggers.
-
-23%
This motor driver expansion board is based on the L293D chip which is designed to drive up to 4 bidirectional DC motors with individual 8-bit speed selection. It can also drive 2 stepper motors (unipolar or bipolar), single coil or double coil, interleaved or micro-stepping. It contains 4 H-bridges which provide up to 0.6 A per bridge (1.2A peak) at voltages from 4.5 V to 36 V. This shield has pull down resistors to keep the motors disabled during power up. It also features a 2-pin terminal block to ensure separate logic and motor external power supplies. This expansion board is compatible with Arduinos Mega, Diecimila, and Duemilanove. This motor driver shield is capable of driving:Four DC motors and two servos, Two DC motors, stepper motor, and two-way servo, Two stepper motors and servos.
-
-2%
Out Of Stock- Supply Voltage : 12 V
- Fused at 5A for additional safety and component protection
- Heated bed control with additional 11A fuse
- Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
- I2C and SPI pins left available for future expansion.
- 2 stepper motor for Z axis in parallel.
-
-14%
W5100 Ethernet Shield
Original price was: ₨3,500.00.₨2,999.00Current price is: ₨2,999.00. Quick View- Operating voltage 5V (supplied from the Arduino Board)
- Ethernet Controller: W5100 with internal 16K buffer
- Connection speed: 10/100Mb
- Connection with Arduino on SPI port
- The Shield contains a number of informational LEDs
- PWR: indicates that the board and shield are powered
- LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
- FULLD: indicates that the network connection is full duplex
- 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
- RX: flashes when the shield receives data
- TX: flashes when the shield sends data
- TX: flashes when the shield sends data
- COLL: flashes when network collisions are detected