Accelero, Gyro. IMU, Magneto

  • You've just added this product to the cart:

    10 DOF IMU Sensor

    10 DOF IMU Sensor
    0 out of 5

    10 DOF IMU Sensor

    3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.

    ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.

    1,850.00
  • You've just added this product to the cart:

    10 DOF Mems IMU Sensor

    10 DOF Mems IMU Sensor
    0 out of 5

    10 DOF Mems IMU Sensor

    INTRODUCTION

    At the beginning,the inertial measurement unit is an electronic device that measures and reports on a craft’s velocity, orientation, and gravitational forces, using a combination of accelerometers,gyroscopes, and magnetometers. Now IMUs are commonly used in the Human-computer interaction(HCI), navigational purposes and balancing technology used in the Segway Personal Transporter as we all known.
    The 10 DOF(degrees of the freedom) sensor is a compact and low cost IMU from DFRobot. It integrates the ADXL345 accelerometer, the HMC5883L magnetometer,the ITG-3205 gyro and the BMP085 barometric pressure sensor. It’s suitable for most of the controlling system because of the small dimension. The mounting holes make it possible to provide the highly accurate and stable sensor data.It embeds a low noise LDO regulator for supplying a wide range power input.Works with 3~8 volts power input.Certainly,the 10 DOF sensor is directly compatible with your Arduino boards.

    4,200.00
  • You've just added this product to the cart:

    GY-273 Magneto HMC5883L

    GY-273 Magneto HMC5883L
    0 out of 5

    GY-273 Magneto HMC5883L

    This is a breakout board for Honeywell’s HMC5883L, a 3-axis digital compass. Communication with the HMC5883L is simple and all done through an I2C interface, making it Arduino compatible.

    This module can be connected to variety of microprocessors via I2C bus. It comes with a 5V->3.3V regulator, I2C pull-ups on the 3.3V internal power-supply and decoupling capacitors. This module also supports I2C communication at both 3.3V-5V logic level, you can interface this module directly from an Arduino, no pull-ups resistors needed, since they are already included in the module.

    350.00
  • You've just added this product to the cart:

    GY-291 ADXL 345

    GY-291 ADXL 345
    0 out of 5

    GY-291 ADXL 345

    GY-291 ADXL345 3-Axis Accelerometer is a sensor board based on ADXL345 accelerometer integrated circuit. The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.

    400.00
  • You've just added this product to the cart:

    GY-521 MPU6050 Module 6DOF

    GY-521 MPU6050 Module 6DOF
    0 out of 5

    GY-521 MPU6050 Module 6DOF

    The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.

    400.00
  • You've just added this product to the cart:

    GY-61 ADXL335

    GY-61 ADXL335
    0 out of 5

    GY-61 ADXL335

    This breakout comes with 3 analog outputs for X, Y and Z axis measurements on a 0.75″x0.75″ breakout board. The ADXL335 is the latest and greatest from Analog Devices, known for their exceptional quality MEMS devices.

    300.00
  • You've just added this product to the cart:

    Hall Sensor 44E

    -17%
    0 out of 5

    Hall Sensor 44E

    44E is a switched Hall effect IC. It has an embedded hall chip on it and is used for sensing magnetic field. It also has an amplifier embedded which amplifies the hall voltage, a schmitt trigger which helps is hysteresis switching for noise rejection and an open collector output.

    180.00 150.00
  • You've just added this product to the cart:

    HMC5883L Gyro

    -8%
    0 out of 5

    HMC5883L Gyro

    It is a surface mount multi chip module designed to sense low magnetic field with a digital interface for applications such as magnetometry.

    520.00 480.00
  • You've just added this product to the cart:

    MPU 9250

    -18%
    0 out of 5

    MPU 9250

    This is a system package which combines two chips: MPU-6500 containing 3-axis gyroscope and 3 axis accelerometer. The oher chip is a Digital Motion Processor capable of processing complex motionFusion algorithms.

    920.00 750.00
  • You've just added this product to the cart:

    MPU6050

    -31%
    0 out of 5

    MPU6050

    This is a six axis IMU sensor, which means that it has the ability to six outputs at a time. It is a sensor based on MEMS(microelectromechanical systems) technology.

    350.00 240.00
  • You've just added this product to the cart:

    Reed Module ky-021

    -21%
    0 out of 5

    Reed Module ky-021

    It is a magnetic sensor and normally switches its state when exposed to a magnetic field. It is compatible with popular electronic platforms like Arduino, ESP8266.

    190.00 150.00