Sensors

  • You've just added this product to the cart:

    10 DOF IMU Sensor

    10 DOF IMU Sensor
    0 out of 5

    10 DOF IMU Sensor

    3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.

    ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.

    1,850.00
  • You've just added this product to the cart:

    10 DOF Mems IMU Sensor

    10 DOF Mems IMU Sensor
    0 out of 5

    10 DOF Mems IMU Sensor

    INTRODUCTION

    At the beginning,the inertial measurement unit is an electronic device that measures and reports on a craft’s velocity, orientation, and gravitational forces, using a combination of accelerometers,gyroscopes, and magnetometers. Now IMUs are commonly used in the Human-computer interaction(HCI), navigational purposes and balancing technology used in the Segway Personal Transporter as we all known.
    The 10 DOF(degrees of the freedom) sensor is a compact and low cost IMU from DFRobot. It integrates the ADXL345 accelerometer, the HMC5883L magnetometer,the ITG-3205 gyro and the BMP085 barometric pressure sensor. It’s suitable for most of the controlling system because of the small dimension. The mounting holes make it possible to provide the highly accurate and stable sensor data.It embeds a low noise LDO regulator for supplying a wide range power input.Works with 3~8 volts power input.Certainly,the 10 DOF sensor is directly compatible with your Arduino boards.

    4,200.00
  • You've just added this product to the cart:

    18B20 Temperature Module

    18B20 Temperature Module
    0 out of 5

    18B20 Temperature Module

    These 3-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontroller using a single digital pin, and you can even connect multiple ones to the same pin, each one has a unique 64-bit ID burned in at the factory to differentiate them. Usable with 3.0-5.0V systems.

    275.00
  • You've just added this product to the cart:

    2way IR Avoidance Sensor

    2way IR Avoidance Sensor
    0 out of 5

    2way IR Avoidance Sensor

    2-way Obstacle Avoidance Module Infrared Reflective Sensor Module

    Each one-way infrared sensor continuously emits infrared emission tube, when no infrared rays emitted or reflected back but the strength is not large enough, the infrared receiver has been in the off state, TTL output terminal of the module is high level, the corresponding indicator LED remains off state; occurs when an object is detected within the detection range, infrared is reflected back and the intensity is large enough, infrared receiver is turned on, then the TTL output of the module is low, indicating diode is lit.

    100.00
  • You've just added this product to the cart:

    ACS712 Current Sensor 20A

    -21%
    0 out of 5

    ACS712 Current Sensor 20A

    A high accuracy current sensor which can detect AC or DC current upto 20A. The signal can be read via analog I/O port of a microcontroller.

    350.00 275.00
  • You've just added this product to the cart:

    ACS712 Current Sensor 30A

    -22%
    0 out of 5

    ACS712 Current Sensor 30A

    A high accuracy current sensor which can detect AC or DC current upto 30A. The signal can be read via analog I/O port of a microcontroller.

    360.00 280.00
  • You've just added this product to the cart:

    ACS712 Current Sensor 5A

    -26%
    0 out of 5

    ACS712 Current Sensor 5A

    A high accuracy current sensor which can detect AC or DC current upto 5A. The signal can be read via analog I/O port of a microcontroller.

    350.00 260.00
  • You've just added this product to the cart:

    Analog AC Current Sensor

    Analog AC Current Sensor
    0 out of 5

    Analog AC Current Sensor

    INTRODUCTION

    When you want to measure AC current it is impractical and hazardous to cut in to your live wiring. The analog AC current sensor developed by DFRobot is a good solution to this problem. Using induction you can measure AC current without intrusive methods. Place your AC wire inside the unit, connect the unit to the sensor board using the 3.5mm jack connector and connect the sensor board to an analog input on your microcontroller. Use this sensor to measure AC motors, lighting equipment, air compressors or any other devices that use AC current.

    3,000.00
  • You've just added this product to the cart:

    Analog Liquid Level Sensor (FS-IR02)

    Analog Liquid Level Sensor (FS-IR02)
    0 out of 5

    Analog Liquid Level Sensor (FS-IR02)

    INTRODUCTION

    This is a photoelectric liquid level sensor that is operates using optical principles. The advantages of this are good sensitivity and no need for mechanical parts – meaning less calibration! The corrosion resistant probe is easily mounted and can handle high temperature and high pressure. The sensor is equipped with an interface adapter for compatibility with the DFRobot “Gravity” interface.

    950.00
  • 0 out of 5

    Biomedical Sensor Pad (10 pack)

    This is a 10 pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are perfect for short-term monitoring of Neurofeedback and Biofeedback purposes. They are to be used once and are very handy because of integrated, latex-free gel. Each pad adheres very well to the skin and the snap connector can be pushed on or removed from the electrode lead with no issue.

    1,300.00
  • You've just added this product to the cart:

    BMP 180/GY68 Pressure Sensor

    -31%
    0 out of 5

    BMP 180/GY68 Pressure Sensor

    It is a very small pressure sensor which measure the absolute pressure of the air around. Its measuring range is from 300 to 1100hpa with an accuracy down to 0.02hpa.

    260.00 180.00
  • You've just added this product to the cart:

    BMP180 Pressure Sensor

    BMP180 Pressure Sensor
    0 out of 5

    BMP180 Pressure Sensor

    BMP180 is the best low-cost sensing solution for measuring barometric pressure and temperature. Because pressure changes with altitude you can also use it as an altimeter! The sensor is soldered onto a PCB with a 3.3V regulator, I2C level shifter and pull-up resistors on the I2C pins. The BMP180 is the next-generation of sensors from Bosch, and replaces the BMP085

    400.00