Modules

  • You've just added this product to the cart:

    2Channel Relay Modue

    -13%
    0 out of 5

    2Channel Relay Modue

    The 2 channel relay module is an interface board which has the ability to control various appliances and equipments due to its relays module. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller.

    160.00 140.00
  • You've just added this product to the cart:

    Analog/Digital LDR Module

    -26%
    0 out of 5

    Analog/Digital LDR Module

    LDR Module gives an analog output voltage. So the output is connected to analog pin of the microcontroller and then the builtin ADC converts these voltage levels into Digital outputs according the microcontroller’s range.

    175.00 130.00
  • You've just added this product to the cart:

    APM Power Module

    -28%
    0 out of 5

    APM Power Module

    The power module has the ability to provide APM lossless power from a LiPo battery as well as current consumption and voltage measurements through 6-pos cable. The on board regulator switch has the ability of giving outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery.

    1,230.00 890.00
  • You've just added this product to the cart:

    DS1302 RTC Module

    -36%
    0 out of 5

    DS1302 RTC Module

    DS1302 is a tickle charge timekeeping chip containing real time clock and 31 bytes of Static RAM. It uses serial communication to interact with microcontrollers.

    250.00 160.00
  • You've just added this product to the cart:

    ECG AD8232

    0 out of 5

    ECG AD8232

    AD8232 is a heart rate tracking sensor. The sensor is used to measure the electrical activity of a heart. A common example for this device is a ECG monitor which is used to track heart’s beating condition.

  • You've just added this product to the cart:

    Joystick Module

    -22%
    0 out of 5

    Joystick Module

    Joystick module looks same as the analog joysticks found in gamepads. Module is mounted with two potentiometers at a 90 degree angle. These potentiometers are connected to a short stick centered by springs. The output voltage varies from 0V to 5V as the joystick moves depending upon its direction as well.

    180.00 140.00
  • You've just added this product to the cart:

    L298N

    0 out of 5

    L298N

    The L298 is an integrated monolithic circuit. It is a high voltage , high current dual full-bridge driver designed to accept standard TTL logic level sand drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the in-put signals .The emitters of the lower transistors of each bridge are connected together rand the corresponding external terminal can be used for the connection of an external sensing resistor. An additional Supply input is provided so that the logic works at a lower voltage.

  • You've just added this product to the cart:

    L298N Dual H-Bridge Module

    L298N Dual H-Bridge Module
    0 out of 5

    L298N Dual H-Bridge Module

    200.00
  • You've just added this product to the cart:

    Large Current Motor Driver Module BTS7960 - 43A

    0 out of 5

    Large Current Motor Driver Module BTS7960 – 43A

    The drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection. Double BTS7960 H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive! High Current up to 43A! Input voltage: 6V-27V.

  • You've just added this product to the cart:

    LDR Relay Module

    -42%
    0 out of 5

    LDR Relay Module

    It is a single relay board which can be used to turn on lights, fans and other oon/off devices. It has a range of devices ranges upto rating of 10A via on the board relay. It can also control high power devices upto 7A with just providing high/low signal.

    600.00 350.00
  • You've just added this product to the cart:

    MAX490

    0 out of 5

    MAX490

    The MAX490 is low-power transceivers for RS-485 and RS-422 communication. Each part contains one driver and one receiver.

  • You've just added this product to the cart:

    Mic Module

    -20%
    0 out of 5

    Mic Module

    Microphone module is mainly used for sound detection. On board microphone is used is highly sensitive due to which it can efficiently detect any sound. It comes with a power LED and status LED as indicator.

    150.00 120.00